09-9335 - Laserfiche WebLink

Browse Search

June 15, 2005 DN -6999 • A1-350 8 N OT 1 F 1 E R `R' Addressable Monitor Modules for the FireWarden -100: by Honeywell NMM -100, NMM -100P, NZM -100, NDM -100 Section: Addressable GENERAL - California Four different monitor modules are available for \ State Fire NOTIFIER's FireWarden -100 intelligent fire alarm control M EA ( ) Marshal panels to suit a variety of applications. Monitor modules .. vol 7300- 0028 :230 are used to supervise a circuit of dry- contact in ut de 72-01-E Vol. II p (except NDM - 100) '" (except NDM - 100) vices, such as conventional heat detectors and pull sta- LISTED tions, or monitor and power a circuit of two -wire smoke S635 detectors (NZM 100). NMM -100 — The NMM -100 Monitor Module is a standard - sized module (typically mounts to a 4.0" [10.16 cm] square APPROVED box) that supervises either a Class A (Style D) or Class B (Style B) circuit of dry- contact input devices. NMM -100P — The NMM -100P is a Miniature Monitor Mod- , n n ■ ule (a mere 1.3" (3.302 cm) H x 2.75" (6.985 cm) W x 0.5" C ,--„,\ (1.270 cm) D) used to supervise a Class B (Style B) cir- 0 1 1 cuit. Its compact design allows the NMM -100P to be O mounted in a single -gang box behind the device it is moni- toring. ®9 6 0 L,I NZM -100 — The NZM -100 Interface Module is a stan- ® 8 3 s � .. �i 1 ® i dard -sized module used to monitor and supervise com- 2 13 patible two -wire, 24 volt, smoke detectors on a Class A ® 7 TE s so isg 2 ® ` (Style D) or Class B (Style B) circuit. 6 A 3 NDM -100 — The NDM -100 Dual Monitor Module is a stan- ®5 z��y' 4 ® o dard -sized module (typically mounts to a 4.0" [10.16 cm] ONES ° square box) that supervises two Class B (Style 8) circuits LOOP ADDRESS of dry- contact input devices. ( \ /2 c n NMM -100 MONITOR MODULE ` 0 • Built -in type identification automatically identifies this de- U U vice as a monitor module to the control panel. • Powered directly by two -wire SLC loop. No additional NMM -100 and NZM -100 power required. • High noise (EMF /RFI) immunity. quired for supervision of the Style D circuit. Maximum IDC • SEMS screws with clamping plates for ease of wiring. resistance is 1,500 ohms. • Direct Decade 01 – 99 (FireWarden -100) entry of ad- NMM - 100 Operation — Each NMM -100 uses one of dress. 99 (FireWarden -100) available module addresses on an • LED flashes red during normal operation and latches SLC loop. It responds to regular polls from the control on steady to indicate alarm. panel and reports its type and the status (open /normal/ The NMM -100 Monitor Module is intended for use in intel- short) of its Initiating Device Circuit (IDC). A flashing LED ligent, two -wire systems, where the individual address of indicates that the module is in communication with the con - each module is selected using the built -in rotary switches. trol panel. The LED latches steady on alarm (subject to It provides either a two -wire or four -wire Class A or Class current limitations on the loop). B fault - tolerant Initiating Device Circuit (IDC) for normally- NMM -100 Specifications open- contact fire alarm and supervisory devices. Nominal operating voltage: 15 to 32 VDC. NMM -100 Applications — Use to monitor a zone of Maximum current draw: 5.1 mA (LED on). four -wire smoke detectors, manual fire alarm pull stations, Average operat current: 400 pA (LED flashing). waterflow devices, or other normally -open dry- contact alarm activation devices. May also be used to monitor EOL resistance: 47K ohms. normally -open supervisory devices with special supervi- Temperature range: 32 °F to 120 °F (0 °C to 49 °C). sory indication at the control panel. Monitored circuit may Humidity range: 10% to 93% noncondensing. be wired as an NFPA Style B (Class B) or Style D (Class D) Dimensions: 4.5" (11.43 cm) high x 4.0" (10.16 cm) wide x Initiating Device Circuit. A 47K ohm End -of -Line Resistor 1.25" (3.175 cm) deep. Mounts to a 4.0" (10.16 cm) square (provided) terminates the Style B circuit. No resistor is re- x 2.125" (5.398 cm) deep box. This document is not intended to be used for installation purposes. We try to keep our ISO 9001 product information up -to -date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact NOTIFIER. Phone: (203) 484 -7161 FAX: (203) 484 -7118 C E Ft T 1 F I E ID 0 NOTI FI ER' lI01MWr IMNNRC1UIIri by Honeywell 12 Clintonville Road, Northford, Connecticut 06472 QUALITY SYSTEMS DN -6999 • 06/15/05 — Page 1 of 3