09-9335 - Laserfiche WebLink

Browse Search

NMM -100P MINI MONITOR MODULE NZM -100 INTERFACE MODULE • Built -in type identification automatically identifies this de- • Supports compatible two -wire smoke detectors. vice as a ,monitor module to the FireWarden -100. • Supervises IDC wiring and connection of external power • Powered directly by two -wire SLC Loop. No additional source (resettable). power required. • High noise (EMF /RFI) immunity. • High noise (EMF /RFI) immunity. • SEMS screws with clamping plates for ease of wiring. • Tinned, stripped leads for ease of wiring. • Direct -dial entry of address (01 -99 for FireWarden -100). • Direct -dial entry of address (01 -99 for FireWarden -100). • LED flashes during normal operation. The NMM -100P Mini Monitor Module can be installed in a • LED latches steady to indicate alarm on command from single -gang junction directly behind the monitored unit. Its control panel. small size and light weight allow it to be installed without The NZM -100 Interface Module is intended for use in in- rigid mounting. The NMM -100P is intended for use in in- telligent, addressable systems, where the individual ad- telligent, two -wire systems where the individual address dress of each module is selected using built -in rotary of each module is selected using rotary switches. It pro- switches. This module allows intelligent panels to inter - vides a two -wire initiating device circuit for normally -open- face and monitor two -wire conventional smoke detectors. contact fire alarm and security devices. It transmits the status (normal, open, or alarm) of one full zone of conventional detectors back to the control panel. 1 0 1 ADDRESS 0 1 All two -wire detectors being monitored must be UL -com- 13 i, 2 2 patible with the module. 10 v 5 LOOP �� 4 NZM - 1 00 Applications — Use the NZM to moni tor a zone of two -wire smoke detectors. The monitored cir 9 8 7 s i g 8 6 3 cuit may be wired as an NFPA Style B (Class B) or Style D TENS ONES z, (Class A) Initiating Device Circuit. A 3.9 K ohm End -of -Line 1n 10 Resistor (provided) terminates the end of the Style B or D ig rl (class B or A) circuit (maximum IDC loop resistance is 25 o 1 ,_„ ohms). Install ELR across terminals 8 and 9 for Style D application. O J q v NZM - 100 Operation — Each NZM -100 uses one of p Q 99 (FireWarden -100) available module addresses on an EX 5 m panel SLC loop. and reports It its responds type to and regular the polls status from (open /norma control l/ short) of its Initiating Device Circuit (IDC). A flashing LED indicates that the module is in communication with the con- 1 1 I I trol panel. The LED latches steady on alarm (subject to current limitations on the loop). NMM - 100P Applications — Use to monitor a single NZM - 100 Specifications device or a zone of four -wire smoke detectors, manual fire Nominal operating voltage: 15 to 32 VDC. alarm pull stations, waterflow devices, or other normally - open dry- contact devices. May also be used to monitor nor- Maximum current draw: 5.1 mA (LED on). mally -open supervisory devices with special supervisory Average operating current: 270 pA (LED flashing). indication at the control panel. Monitored circuit/device is EOL resistance: 3.9K ohms. wired as an NFPA Style B (Class B) Initiating Device Cir- cuit. A 47K ohm End -of -Line Resistor (provided) terminates External supply voltage (between Terminals T3 and T4): the circuit. DC voltage: 18 to 28 volts power limited. Ripple voltage: NMM - 100P Operation — Each NMM -100P uses one 0.1 VRMS maximum. Current: 90 mA per module maximum. of 99 (FireWarden -100) available module addresses on Requires regulated, resettable 24 VDC power. an SLC loop. It responds to regular polls from the control Temperature range: 32 °F to 120 "F (0 °C to 49 °C). panel and reports its type and the status (open /normal/ Humidity range: 10% to 93% noncondensing. short) of its Initiating Device Circuit (IDC). Dimensions: 4.5" (11.43 cm) high x 4.0" (10.16 cm) wide x NMM - 100P Specifications 1.25" (3.175 cm) deep. Mounts to a 4.0" (10.16 cm) square Nominal operating voltage: 15 to 32 VDC. x 2.125" (5.398 cm) deep box. Average operating current: 375 pA maximum. EOL resistance: 47K ohms. Temperature range: 32 °F to 120 °F (0 °C to 49 °C). Humidity range: 10% to 93% noncondensing. Dimensions: 1.3" (3.302 cm) high x 2.75" (6.985 cm) wide x 0.5" (1.270 cm) deep. Wire length: 6.0" (15.24 cm) minimum. Page 2 of 3 — DN -6999 • 06/15/05