10-10030 - Laserfiche WebLink

Browse Search

dn- 6997:b • A1-320 NH - 100 Series N OTI F 1 E R Intelligent Addressable Thermal Detectors for FireWarden Series by Honeywell Addressable General The NOTIFIER NH -100 Series thermal detectors are address- able sensors that use a state -of- the -art thermistor sensing cir- cuit for fast response. These sensors provide open -area protection and are intended for use with the FireWarden Series (FireWarden -100 -2 and FireWarden -50) addressable aA" h Fire Alarm Control Panels (FACPs).; The NH -100 and NH -100R sensors provide fixed temperature alarm detection at 135 °F (57 °C). The NH -100R sensor also responds to rate -of -rise conditions of greater than 15 °F (8.3 °C) per minute. The NH -100H is a fixed high- temperature detector activates at 190 °F (88 °C). These thermal detectors pro- 6936phol .Q vide addressable property protection in a variety of applica- tions. NH - 100 with B710LP base Two LEDs on each sensor light to provide a local, visible sen- sor indication. Remote LED annunciator capability is available as an optional accessory (RA400Z). • Low standby current. Features • 94 -5V plastic flammability rating. Options: SLC loop: Remote LED output connection to optional RA400Z • • Two -wire SLC loop connection. remote LED annunciator. • Unit uses base for wiring. • Recessed (RMK400) or surface (SMK400E) base mount - Addressing: ing kits. • Addressable by device. • Direct Decade entry of address: 01 — 99 with FireWarden- Installation 100 -2, 01 — 50 with FireWarden -50. NH -100 Series plug -in intelligent thermal detectors use a Architecture: detachable base to simplify installation, service and mainte- • Sleek, low- profile, stylish design. nance. Installation instructions are shipped with each detector. • State -of- the -art thermistor technology for fast response. Mount base (all that types) on box that is at least 1.5' (3.81 Integral communications and built -in device-type cm) deep. Suitable boxes include: • type identifica- lion. • 4.0' (10.16 cm) square box. • Built -in tamper resistant feature. • 3.5" (8.89 cm) or 4.0' (10.16 cm) octagonal box. • Built -in functional test switch activated by external magnet. • Single -gang box (except relay or isolator base). Operation: NOTE: Because of the inherent supervision provided by the SLC loop, end -of -line resistors are not required. Wiring 'T -taps" or • Factory preset at 135 °F (57 °C) for the NH -100 and NH- branches are permitted for Style 4 (Class "B") wiring only. 100R; 190 °F (88 °C) for the NH -100H. • Rate -of -rise triggers at 15 °F (8.3 °C) per minute for the NH- Applications 100R. • 360 ° -field viewing angle of the visual alarm indicators (two Use thermal detectors for protection of property. bicolor LEDs). LEDs blink green in Normal condition and turn on steady red in Alarm. Construction • Visible LEDs "blink" every time the unit is addressed. These detectors are constructed of off-white Bayblend®. The Mechanicals: NH -100 Series plug -in intelligent thermal detectors are designed to commercial standards and offer an attractive • Sealed against back pressure. appearance. • SEMS screws for wiring of the separate base. • Designed for direct - surface or electrical -box mounting. Operation • Plugs into separate base for ease of installation and main- Each NH -100 Series detector uses one of 99 (FireWarden - tenance. 100 -2) or 50 (FireWarden -50) possible addresses on a control • Separate base allows interchange of photoelectric, ioniza- panel SLC loop. It responds to regular polls from the control tion and thermal sensors. panel and reports its type and the status. If it receives a test Other system features: command from the panel (or a local magnet test), it stimulates its electronics and reports an alarm. It blinks its LEDs when • Remote test feature from the panel. polled and turns the LEDs on when commanded by the panel. • Walk test with address display. dn- 6997:b • 06/08/09 — Page 1 of 2