11-11786 - Laserfiche WebLink

Browse Search

• Direct-dial entry of address: 01 — 159 on NFW-100, 01 — 99 • LED flashes during normal operation. on NFW-50. • LED latches steady to indicate alarm on command from control panel. 3 14 �5 0� ADDRESS o� The NZM-100 Interface Module is intended for use in inteili- ��3 z� 2 9ent, addressable systems, where the individual address of 3 �? O 4 LOOP O 4 each module is selected using built-in rotary switches. This i 10 5 � 5 I module allows intelligent panels to interface and monitor two- wire conventional smoke detectors. It transmits the status (nor- 9 � 6 9 8 7 6 i mal, open, or alarm) of one full zone of conventional detectors � TENS ONES i back to the control panel. All two-wire detectors being moni- '` tored must be UL compatible with the module. i: NZM-100 APPLICATIONS � i � Y Use the NZM-100 to monitor a zone of two-wire smoke detec- O ° W W`� UQ tors. The monitored circuit may be wired as an NFPA Style B � � �� m (Class B) or Style D(Class A) Initiating Device Circuit. A 3.9 K ohm End-of-Line Resistor (provided) terminates the end of the ti± Style B or D(class B or A) circuit (maximum IDC loop resis- tance is 25 ohms). Install ELR across terminals 8 and 9 for Style D application. NZM-100 OPERATION The NMM-100P Mini Monitor Module can be installed in a sin- Each NZM-100 uses one of the available module addresses gle-gang junction directly behind the monitored unit. Its small size and light weight allow it to be installed without rigid mount- on an SLC loop. It responds to regular polis from the controi ing. The NMM-100P is intended for use in intelligent, two-wire panei and reports its type and the status (open/normal/short) systems where the individual address of each module is of its Initiating Device Circuit (IDC). A flashing LED indicates selected using rotary switches. It provides a two-wire initiating that the module is in communication with the control panel. device circuit for normally-open-contact fire alarm and security The LED latches steady on alarm (subject to current limita- devices. NMM-t00P tions on the loop). NMM-f00P APPLICAT/ONS NZM-100 SPECIFICATIONS Use to monitor a single device or a zone of four-wire smoke Nominal operating voltage: 15 to 32 VDC. detectors, manual fire alarm pull stations, waterflow devices, or Maximum current draw: 5.1 mA (LED on). other normally-open dry-contact devices. May also be used to Maximum IDC wiring resistance• 25 ohms. monitor normally-open supervisory devices with speciai super- ' visory indication at the control panei. Monitored circuiUdevice Maximum operating current: 270 NA (LED fiashing). is wired as an NFPA Style B(Class B) Initiating Device Circuit. EOL resistance• 3.9K ohms. A 47K ohm End-of-Line Resistor (provided) terminates the cir- � cuit. External supply voltage (between Terminals T3 and T4): DC voltage: 24 volts power limited. Ripple voltage: 0.1 Vrms NMM-100P OPERATION maximum. Current: 90 mA per module maximum. Each NMM-100P uses one of the available module addresses Temperature range: 32°F to 120°F (0°C to 49°C). on an SLC loop. It responds to regular polls from the control Humidity range: 10% to 93% noncondensing. panel and reports its type and the status (open/normal/short) of its Initiating Device Circuit (IDC). Dimensions: 4.5" (11.43 cm) high x 4' (10.16 cm) wide x 1.25" (3.175 cm) deep. Mounts to a 4" (10 16 cm) square x NMM-700P SPECIFICATIDNS 2.125" (5.398 cm) deep box. Nominal operating voltage: 15 to 32 VDC. Maximum operating current: 375 NA. NDM Duai Monitor Module Maximum IDC wiring reststance: 1,500 ohms. The NDM-100 Dual Monitor Module is intended for use in intel- EOL resistance: 47K ohms. ligent, two-wire systems. It provides two independent two-wire initiating device circuits (IDCs) at two separate, consecutive Temperature range: 32°F to 120°F (0°C to 49°C). addresses. It is capable of monitoring normaily open contact Humidity range• 10% to 93% noncondensing. fire alarm and supervisory devices; or either normally open or � normally ciosed security devices. The module has a single Dimensions: 1.3" (3.302 cm) high x 2.75" (6.985 cm) wide x panel-controlled LED. 0.65" (1.651 cm) deep. NOTE: The NDM-f00 provides two C/ass 8(Style B) lDC circuits Wire length: 6' (15.24 cm} minimum. ONLY. C/ass A (Sty/e D) IDC ci�cuits are NOT supported in any application. NZM 00 Interface Module NDM-100 SPEClFICATIONS • Supports compatible two-wire smoke detectors. Normal operating voltage range: 15 to 32 VDC. • Supervises IDC wiring and connection of external power Maximum current draw: 6.4 mA (LED on). source. • High noise (EMF/RFI) immuniry. Maximum operating current: 750 NA (LED flashing). • SEMS screws with clamping plates for ease of wiring. Maximum IDC wiring resistance: 1,500 ohms. • Direct-dial entry of address: 01 — 159 on NFW-100, 01 — 99 EOL resistance: 47K ohms. on NFW-50. Temperature range: 32° to 120°F (0° to 49°C). Page 2 of 6— dn-6999:a • OM28/08 P.10