11-11786 - Laserfiche WebLink

Browse Search

dn-6999:a•A1-350 Mon't r Modules � N OT 1 F 1 E R NMM-1�NMM-100P NZM-100 and � —� � � � NDM-100 for FireWarden Systems by Honeywel{ General Four different monitor modules are available for Notifier's Fire- f� � � C� Warden-series intelligent control panels to suit a variety of �J U applications. Monitor modules are used to supervise a circuit of dry-contact input devices, such as conventional heat detec- p� 9 ,e� o tors and puli stations, or monitor and power a circuit of two- �� e��_ �� wire smoke detectors (NZM-100) _ �,�„�0,5+�' 2 NMM-100 and NZM-100 a Ql6y NMM-100 is a standard-sized module (typically mounts to a 4" �� s 3 [10.16 cm] square box) that supervises either a Class A(Style S a D) or Ciass B(Style B) circuit of dry-contact input devices. LOOP ^°°REu o � NMM-100P is a miniature monitor module (a mere 1.3° (3.302 � � Q cm) H x 2.75" (6.985 cm) W x 0.5" (1.270 cm) D) used to � supervise a Class B(Style B) circuit of dry-contact input devices. Its compact design aliows the NMM-100P to often be � � O C� mounted in a single-gang box behind the device it monitors. U NZM-100 is a standard-sized module used to monitor and y � o � supervise compatible two-wire, 24 volt, smoke detectors on a detail of NDM-100 - note : r Class A(Sryle D) or Class B(Style B) circuit. "ones" addresses are 0 2 8= , a � 3 � e �� , 2 g NDM-100 is a standard-sized dual monitor module used to 4, 6, 8 only � 6 6 � 3 monitor and supervise two independent two-wire Style B s�: a (Class B) dry-contact initiating device circuits (IDCs) at two �° LOOP ADDRESS separate, consecutive addresses in intelligent, two-wire systems. o Q O O � —� NMM-100 Monitor Module • Built-in type identification automatically identifies this device as a monitor module to the control panel. • Powered directly by two-wire SLC loop. No additional power NMM-100 OPERATION required. Each NMM-100 uses one of the available module addresses • High noise (EMF/RFI) immunity. on an SLC loop. It responds to regular polls from the control • SEMS screws with clamping plates for ease of wiring. panel and reports its rype and the status (open/normal/short) of its Initiating Device Circuit (IDC). A fiashing LED indicates • Direct-dial entry of address: 01 — 159 on NFW-100, 01 — 99 that the module is in communication with the control panel. on NFW-50. The LED latches steady on alarm (subject to current limita- • LED flashes during normal operation and latches on steady tions on the loop). to indicate alarm. The NMM-100 Monitor Module is intended for use in intelli- NMM-100 SPEC/FICATIONS gent, two-wire systems, where the individual address of each Nominal operating voltage: 15 to 32 VDC. module is selected using the built-in rotary switches. It pro- Maximum current draw• 5.1 mA (LED on). vides either a two-wire or four-wire fault-tolerant Initiating � Device Circuit (IDC) for normally-open-contact fire alarm and Maximum operating current: 375 NA (LED flashing). supervisory devices. The module has a panel-controiled LED Maximum IDC wiring resistance: 1,500 ohms. indicator. EOL resistance: 47K ohms. NMM-100 APPL/CATIONS Temperature range: 32°F to 120°F (0°C to 49°C). Use to monitor a zone of four-wire smoke detectors, manual Humidity range: 10% to 93% noncondensing. fire alarm pull stations, waterfiow devices, or other normally- open dry-contact alarm activation devices. May also be used Dimensions: 4.5" (11.43 cm) high x 4° (10.16 cm) wide x to monitor normally-open supervisory devices with special 1•25` (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x supervisory indication at the control panel. Monitored circuit 2.125" (5.398 cm) deep box. may be wired as an NFPA Style B(Class B) or Sryle D(Clas A) Initiating Device Circuit. A 47K ohm End-of-Line Re stsm� NMM-1 OOP Mini Monitor Module (provided) terminates the Style B circuit. No resistor is '. guilt-in type identification automatically identifies this device required for supervision of the Style D circuit. as a monitor module to the panel. • Powered directly by two-wire FACP. No additional power required. • High noise (EMF/RFI) immuniry. • Tinned, stripped leads for ease of wiring. dn-6999:a • 04/28/OS — Page 1 of 6 P. 9