11-11786 - Laserfiche WebLink

Browse Search

Operation Product Line Information Each NP-100lT/R uses one of 99 possible addresses orr4h� NP-100: Adressable photoelectric detector; 6710LP base FireWarden-100-2 and one of 50 possible addresses on the included. FireWarden-50 Signaling Line Circuit (SLC). It responds to NP-100A: Sames as NP-100 with ULC Listing (B710LPA base regular polls from the system and reports its type and status. �ncluded) The NP-100lT/R addressable photoelectric sensor's unique NP-100T: Same as NP-100 but with therma/ element; unipolar chamber responds quickly and uniformly to a broad B710LP base included. range of smoke conditions and can withstand wind gusts up to 4,000 feet-per-minute (20 m/sec.) without sending an alarm NP-100TA: Same as NP-100T with ULC Listing level signal. Because of its unipolar chamber, the NP-100lf/R (g710LPAbase included). is approximately two times more responsive than most photo- NP-100R: Remote test capable addressable photoelectric electric sensors. This makes it a more stable detector detector for use with a DNR(W) duct detector housing. Detector Sensitivity Test B710LP: Plug-in detector base. Dimensions: 6.1" (15.5 cm). Mounting: 4.0' (10 16 cm) square box with or without plaster Each detector can have its sensitivity tested (required per ring, 4.0" (10.16 cm) octagonal box, 3.5" (8.89 cm) octagonal NFPA 72, Chapter 14 on lnspection, Testing and Maintenance) box, or single-gang box. All mounting boxes have a minimum when installed/connected to a FireWarden-100-2 or FireWar- depth of 1.5" (3.81 cm). den-50 addressable fire alarm control panel. The results of the g224RB: Plug-in System Sensor relay detector base. Diame- sensitivity test can be printed off the FireWarden-100-2 or Fire- ter: 6.2" (15.75 cm). Mounting: 4.0" (10.16 cm) square box Warden-50 for record keeping. with or without plaster ring, 4 0" (10 16 cm) octagonal box, or 3.5" (8.89 cm) octagonal box. All mounting boxes have a mini- Specification mum depth of 1.5' (3.81 cm). Voltage range: 15 - 32 VDC (peak) B224B1: Plug-in System Sensor Isolator detector base. Maxi- Standby current• 300 uA � 24 VDC. mum 25 devices between isolator bases (see DN-6994). � Dfameter: 62" (15.75 cm). Mounting: 4.0' (10 16 cm) square LED current: 6.5 mA � 24 VDC (latched "ON"). box with or without plaster ring, 4 0" (10.16 cm) octagonal box, Air velocity: 4,000 ft./min. (20 m/sec.) maximum. or 3.5" (8.89 cm) octagonal box. All mounting boxes have a minimum depth of 1.5' (3.81 cm). Diameter: 6.1' (15.5 cm) installed in B710LP base. B200SR: Sounder base capable of producing temporai-3 or Hetght: 2.1' (5.33 cm} installed in B710LP base. steady sound output. Weight: 3.6 oz. (102 g). ACCESSORIES: Operating temperature range: for NP-10�: 0°C to 49°C (32°F Rp100Z(A): Remote LED annunciator. 3- 32 VDC. Mounts to to 120°F); forNP-1�OT: 0°C to 38°C (32°F to 100°F). NP-100R: a U.S. single-gang electrical box. For use with 650i and installed in a DNR(W) -20°C to 70°C (-4°F to 158°F). B710LP bases only. Temperature: 0°C - 49°C (32°F - 120°F�. SMK400E: Surface mounting kit provides for entry of surface Relative humidity: 10% - 93%, non-condensing. wiring conduit. For use with 8501 base only. Listings RMK400: Recessed mounting kit. For use wjth 6501 base only. Listings and approvals below apply to the NP-100 and NP- MppAq. magnet. 100T detectors. In some cases, certain modules may not be listed by certain approval agencies, or IisUng may be in pro- MO2-09-00: Test magnet with telescoping handle. cess. Consult factory for latest listing status. XR26: Detector removal tool. Allows installation and/or removal • UL Listed, file S1115. of detector heads from bases in high ceiling applications. • CSFM approved: file 7272-0028:231. XP-4: Extension pole for XR2B. Comes in three 5-foot (1.524 • MEA approved: file 243-02-E Vol. 2. m) sections. • Maryland State Fire Marshal: permit 2173. T55-127-010:Detector removal tool without pole. • FM approved. BCK-200B: Black detector covers, box of 10 . WCK-200B: White detector covers, box of 10 . NOTIFIER� is a registered trademark of Honeywell International Inc. Bayblend� is a registered Vademark of Bayer Corporatlon. d✓2008 by Honeywell Intematlonal Inc. All rights reserved. Unauthorized use of thts document is stricUy prohfbited. I� O 90 � This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. � We cannot cover all specific applications or anticipate all requirements. g�q�� `�� All specifications are subject to change without notice. QUALITY SrSTEMS For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 2 of 2- dn-6995:b • 3112/10 P. 8