11-12206 - Laserfiche WebLink

Browse Search

J �1 S��d i.�.�V 6.4 StormGuardO: 6.4.1 StormGuard� shall be installed in compliance with the requirements for ASTM D1970 underlayment in FBC Sections 1507 for the type of prepared roof covering t:o be installed 6.4.2 For tile roof installations governed by the FRSA/TRI 07320/8-05 Installation Manual, Fourth Edition, use is limited to. ➢ System 1, Option 5 or 6, Section 3.02E or F � System Z, Option 4 or 5, Section 3.02D or E 6 4 3 Back-nailing is required Back-nailing shall consist of minimum 1-inch square or round cap nails spaced 18" o.c. within 3-inch side laps 6.4.4 Prior to removal of release film, align sheets properly starting at the low-point af the roof (eave) with the selvage edge upslope and for minimum 2-inch overhang at eaves and rakes Remove the lower piece of release film and bond to substrate and fold the overhanging 2-inch over the eave and nail into place 12" o.c. Remove the top piece of release film and bond to substrate. Install primed drip edge and fasten to meet FBC Chapter 16 wind load requirements Install 1/8-inch troweling of LeakBusterT"' MatrixT"' 201 Premium SBS Flashing Cement over drip edge. 6 4.5 Continue upslope in a similar manner, maintaining minimum 3-inch side-laps and minimum 6- inch end-laps. Ensure all end laps are staggered at least 18-inch apart. 6 4.6 Use a hand roller to firmly bond side and end laps. 6.5 StormGuardO Ultra-FIexT"': 6.5.1 StormGuard� shall be installed in compliance with the requirement.s for ASTM D1970 underlayment in FBC Sections 1507 for the type of prepared roof covering to be installed 6.5.2 For tile roof installations governed by the FRSA/TRI 07320/8-05 Installation Manual, Fourth Edition, use is limited to: � System 1, Option 5 or 6, Section 3.02E or F > System 2, Option 4 or 5, Section 3.02D or E 6 S 3 For direct-bond to deck applications where the material is not covered within 24 hours, plywood shall be primed with LeakBuster'"' MatrixT'" 307 Premium Asphalt Primer or alternate GAF-ELK accepted ASTM D41 primer at'/z to 3 /a gallon per 100 square 6.5.4 Back-nailing is required Back-nailing shall consist of minimum 1-inch square or round cap nails spaced 18" o.c. within 3-inch side laps. 6 5 5 Prior to removal of release film, align sheets properiy starting at the low-point of the roof (eave) with the selvage edge upslope and for minimum 2-inch overhang at eaves and rakes Roll out approximately 10 feet of inembrane and peel back the first 3 feet of release film Adhere the exposed part to the substrate and unroll the remaining mernbrane Peel off the release film diagonally while holding the membrane tight. 6 5 6 Fold the overhanging 2-inch over the eave and naii into p�ace 12" o c Rernove the top piece of release film and bond to substrate Install primed drip edge and fasten to meet FBC Chapter 16 wind load requirements Install 1/8-inch troweling of LeakBusterT'" Niatrix'"' 201 Premium SBS Flashing Cement over drip edge 6 5.7 Continue upslope in a similar manner, maintaining minimum 3-inch side-laps and minimum 6- inch end-laps. Ensure all end laps are staggered at least 18-inch apart. 6 S 8 Use a hand roller to firmly bond side and end laps Exterior Research and Design, LLC. Evaluation Report 01506.04.08 Certificate ofAuthorization #9503 FL10626 Date of Issuance: 04/25/2008 Page 5 of 9