|
DN-6720:C•H-220
<br /> � �;FMN1=1�(A) FMM-101 (A), N pT 1 F 1 E R°
<br /> ,,,�. �: ��._,f�.� , ?.F �� ���,�_�.��, �J
<br /> FZM-1 (A) & �FDM-r��(A)
<br /> �x".a�"a„r.,_,::�mati?l�i�:m+it
<br /> - Monitor Modules with FlashScan� by H o n eywe I I
<br /> _ �
<br /> General
<br /> Four different monitor modules are available for Notifier's intel- €3'' ��a'
<br /> ligent control panels for a variety of applications. Monitor mod- �F 9 .j*� -Ht
<br /> ules supervise a circuit of dry-contact input devices, such as
<br /> conventional heat detectors and pull stations, or monitor and ,,,,,�,,, �
<br /> power a circuit of two-wire smoke detectors(FZM-1(A)). " .� �
<br /> ��
<br /> FMM-1(A)is a standard-sized module(typicaily mounts to a 4" `"'""""'°
<br /> �,.�,,..� :a:n.r.u.....
<br /> [10 16 cm]square box)that supervises either a Style D(Class ,,,,M„„ ��«�
<br /> A) or Style B(Class B)circuit of dry-contact input devices. � ,My ��,.,,,
<br /> .�.�;:;:..,,,.....�..
<br /> FMM-101(A)is a miniature monitor module a mere 1.3"(3.302 "'"'"'::.:»...,:�,"""`""
<br /> cm) H x 2.75° (6.985 cm) W x 0.5" (1270 cm) D that super- '��'��`'�^"�^*^�'° �
<br /> vises a Style B (Class B) circuit of dry-contact input devices. Y�'�
<br /> Its compact design allows the FMM-101(A)to be mounted in a '.»'"�' ��� ���
<br /> single-gang box behind the device it monitors. 1�• ?
<br /> FZM-1(A)is a standard-sized module that monitors and super- w; � $
<br /> vises compatible two-wire,24 volt,smoke detectors on a Style � �
<br /> D(Class A) or Style B(Class B)circuit. �
<br /> FDM-1(A)is a standard-sized dual monitor module that moni-
<br /> tors and supervises two independent two-wire Style B(Ciass FMM-1(A)(Type H)
<br /> B)dry-contact initiating device circuits(IDCs)at two separate,
<br /> consecutive addresses in intelligent,two-wire systems.
<br /> FlashScan�(U.S. Patent 5,539,389) is a communication pro- A) initiating Device Circuit. A 47K ohm End-of-Line Resistor
<br /> tocol developed by NOTIFIER that greatly increases the speed (provided) terminates the Style B circuit. No resistor is
<br /> of communication between analog intelligent devices. Intelli- required for supervision of the Style D circuit.
<br /> gent devices communicate in a grouped fashion. If one of the FMM-i(A) OPERATION
<br /> devices within the group has new information, the panel CPU
<br /> stops the group poll and concentrates on single points. The Each FMM-1(A) uses one of the available module addresses
<br /> net effect is response speed greater than five times that of on an SLC loop. It responds to regular polls from the control
<br /> other designs. panel and reports its type and the status (open/normal/short)
<br /> of its Initiating Device Circuit(IDC). A flashing LED indicates
<br /> FMM-i(A) Monitor Module that the module is in communication with the control panel.
<br /> The LED latches steady on alarm (subject to current limita-
<br /> • Built-in type identification automatically identifies this device tions on the loop)
<br /> as a monitor module to the control panel.
<br /> • Powered directly by two-wire SLC loop.No additional power FMM-1(A) SPEClF1CAT/ONS
<br /> required. Nominal operating voltage: 15 to 32 VDC.
<br /> • High noise(EMF/RFI)immunity. Maximum current draw:5.0 mA(LED on)
<br /> • SEMS screws with clamping plates for ease of wiring. Average operating current: 350 UA (LED flashing), 1 com-
<br /> • Direct-dial entry of address: 01 —159 on FlashScan loops; munication every 5 seconds,47k EOL.
<br /> 01 —99 on CLIP loops. Maximum IDC wiring resistance:40 ohms.
<br /> • LED flashes green during normal operation (this is a pro- EOL resistance:47K ohms.
<br /> grammable option) and latches on steady red to indicate
<br /> alarm. Temperature range:32°F to 120°F(0°C to 49°C).
<br /> The FMM-1(A) Monitor Module is intended for use in intelli- Humidity range: 10%to 93%noncondensing.
<br /> gent, two-wire systems, where the individual address of each Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x
<br /> module is selected using the built-in rotary switches. It pro- � 25' (3.175 cm) deep. Mounts to a 4' (10.16 cm) square x
<br /> vides either a two-wire or four-wire fault-tolerant Initiating 2 125"(5.398 cm)deep box.
<br /> Device Circuit (IDC) for normaily-open-contact fire alarm and
<br /> supervisory devices. The module has a panei-controlled LED
<br /> indicator The FMM-1(A) can be used to replace MMX-1(A)
<br /> modules in existing systems.
<br /> FMM-1(A)APPLICATIONS
<br /> Use to monitor a zone of four-wire smoke detectors, manual
<br /> fire alarm pull stations, waterflow devices, or other normally-
<br /> open dry-contact alarm activation devices. May also be used
<br /> to monitor normally-open supervisory devices with special
<br /> supervisory indication at the control panel. Monitored circuit
<br /> may be wired as an NFPA Style B(Class B)or Style D(Class
<br /> DN-6720:C•10/06/2010—Page 1 of 4
<br />
|