12-13282 - Laserfiche WebLink

Browse Search

df-52385:A•E-710 1�1355(Aj Series Fl�•��T��Alc�l''t1''1S Intelli � gent Addressable Thermal by Honeywell Detectors � . General The Fire�Lite Alarms H355 Series thermal detectors are addressable sensors that use a state-of-the-art thermistor � sensing circuit for fast response. These sensors are designed to provide open-area protection and are intended for use with the Fire�Lite's addresable Fire Alarm Control Panels(FACPs). ' The H355(A) and H355R(A) sensors provide fixed tempera- � � ture alarm detection at 135°F (57°C). The H355R(A) sensor �3�o,p also responds to rate-of-rise conditions of greater than 15°F r (8.3°C) per minute. The H355HT(A) is a fixed high-tempera- �� ture detector that activates at 190°F (88°C). These thermal � detectors provide cost effective, addressable property protec- � tion in a variety of applications. H355 with B350LP base Two LEDs on each sensor light to provide a local,visible sen- sor indication. Remote LED annunciator capabiliry is available as an optional accessory(P/N RA400Z). • 94-5V plastic flammability rating. F@BtYf"eS Options: SLC loop: • Remote LED output connection to optional RA400Z • Two-wire SLC loop connection. remote LED annunciator. • Unit uses base for wiring. • Recessed (RMK400) or surface (SMK400E) base mount- Addressing: ing kits. • Addressable by device. Installation • Direct Decade entry of address:01 —159 with MS-9600,Ot —99 with MS-9200UD. H355(A) Series plug-in intelligent thermal detectors use a Architecture: detachable base to simplify installation, service and mainte- nance.Installation instructions are shipped with each detector. • Sleek, low-profile,stylish design. Mount base (all base types) on box that is at least 1.5' (3.81 • State-of-the-art thermistor technology for fast response. cm)deep.Suitable boxes include: • Integral communications and built-in device-type identifica- . 4.0"(10 16 cm)square box. tion. Built-in tamper resistant feature. • 3.5'(8.89 cm)or 4.0'(10.16 cm)octagonal box. • Built-in functional test switch activated by external magnet. ' Single-gang box(except relay or isolator base) Operaflon: NOTE:Because of the inherent supervision provided by the SLC loop, end-of-line resistors are not required. Wiring `T-taps" or • Factory preset at 135°F (57°C) for the H355(A) and branches are permitted for Sty/e 4(C/ass`B')wiring on/y. H355R(A); 190°F(88°C)for the H355HT(A). • Rate-of-rise triggers at 15°F (8.3°C) per minute for the APP��cations H355R(A). Use thermal detectors for protection of property. • 360°-field viewing angle of the visual alarm indicators (two bicolor LEDs). LEDs blink green in Normal condition and Construction turn on steady red in Alarm. • Visible LEDs"blink"every time the unit is addressed. These detectors are constructed of off-white BayblendC�. The H355(A) Series plug-in intelligent thermal detectors are Mechan/cals: designed to commercial standards and offer an attractive • Sealed against back pressure. appearance. • SEMS screws for wiring of the separate base. • Designed for direct-surface or electrical-box mounting. �peration • Plugs into separate base for ease of installation and main- Each H355(A) Series detector uses one of 159 (MS-9600)or tenance. 99(MS-9200UD) possible addresses on a control panel SLC • Separate base allows interchange of photoelectric, ioniza- loop. It responds to regular polis from the control panel and tion and thermal sensors. reports its type and the status. If it receives a test command Othersysiem features: from the panel (or a local magnet test), it stimulates its elec- tronics and reports an alarm. It blinks its LEDs when polled • Remote test feature from the panel. and turns the LEDs on when commanded by the panel. The • Walk test with address display. H355(A) Series offers features and performance that repre- • Low standby current. sent the latest in thermal detector technology. df-5238S:A•12/17/08—Page 1 of 2