12-13462 - Laserfiche WebLink

Browse Search

� • • • • • • - • • • IDNet Addressable Communications Compatible. Hardwire Control Applications.For applications Up to ten(10),4009 IDNet NAC Extenders can be where an existing(or new)converitional NAC needs controlled per 4010ES/4100ES/4100U IDNet additional power,the 4009 IDNet NAC Extender can be communications channel;up to five(5)can be controlled controlled directly from the NAC.Either one or two on the 4010 IDNet communications channel.Each output NACs,from either the same,or from different host fire NAC can be individually controlled for general alarm or alarm control panels,can be connected to control the 4009 selective area notification requiring only one point IDNet NAC Extender output NACs.Multiple control address per Extender.Individual Extender NACs can also selections provide flexible operation.(Refer to page 4 for be manually controlled from the host panel.IDNet more'detail.)Alarms from the host panel will activate the controlled extenders will inform the host panel of troubles four,4009 IDNet NAC Extender NACs(or optionally, via lDNet communications.4010ES/4100ES/4100U eight NACs)to extend the alarm. control panels control using multi-point rules,refer to The 4009 IDNet Extender monitors itself and each of its data sheet S4090-0011 for details. output NACs for trouble conditions,including earth Optional IDNet Repeaters.IDNet communications can faults.Extenders wired to convent.ional NACs will be repeated with the optional IDNet Repeater Module or indicate a trouble by opening the path to the NAC's with the optional Fiber Optic Receiver Module.Up to 100 end-of-line resistor,but retaining the ability to respond to of the IDNet channel points can be repeated once(refer to alarms.Individual troubles are also annunciated by LEDs pages 3 and 5 for details).Repeated IDNet communications located on the 4009 IDNet NAC Extender main circuit also support the"device level"earth fault location utility of board.(Refer to page 7 for more diagnostic information.) the host panel. . . . Standard Models Model Description 4009-9201 4009-9202CA" 120 VAC input 4009 IDNet NAC Extender with 4, Class B NACs and 8 A po�ver supply 4009-9301 240 VAC input *ULC listed model Optional Modules(for on-site installation) Model Description Comments Additional four point NAC module, rated 1 5 A Special 4009-9807 Application appliances, 1 A for Regulated 24 DC appliance One maximum power, Class B 4009-9808 Dual Class A adapter(for two NAC outputs) Select as required(4 maximum) 4009-9809 IDNet Repeater, output is Class A or Class B Seiect either an IDNet Repeater or a Fiber 4009-9810 Class B Optic Receiver as required 4009-9811 Fiber Optic Receiver Class A(IDNet),Class X(fiber) 4009-9805 Red Applique for door Select if required 2975-9801 Beige trim 1-7/16"wide(78 mm), use if required for 2975-9802 Semi-Flush Trim Kit Red trim semi-flush installations Battery Selection (select battery size per system requirements) Model Description Camments 2081-9272 6.2 Ah Battery, 12 VDC 2081-9274 10 Ah Battery, 12 VDC Two batteries are required,24 VDC operation 2081-9288 12.7 Ah Battery, 12 VDC 2081-9275 18 Ah Battery, 12 VDC Requires external battery cabinet,two batteries are required,24 VDC operation �External Accessories (select per system requirements) Model Description Comments 4090-9105 IDNet Fiber Optic Class B operation Mounts in six-gang electrical box, refer to 4090-9107 Transmitter Class X operation page 4 for mounting details 4009-9801 External battery cabinet for up to 18 Ah batteries,beige 16-1/4"W x 13-1/2" H x 5-3/4"D (413mmx343mmx146mm) 4081 Series End-of-Line Resistor Harnesses; see data sheet S4081-0003 for details 2 54009-0002-9