12-13716 - Laserfiche WebLink

Browse Search

' DN-6935.D•H-2Q2 FSP-851 (A) Ser�es �� N QT 1 F f E R�R intelligent Plug-In Photoelectr�c Smoke Detectors with FlashScanO by H a r�eywe I( � - General Notifier FSP-851(A) Series intelligent plug-in smoke detectors =; �� . with integral communication provide features that surpass co�- ventional detectors. Detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detec- tor's address to be set with rotary, decimal address switches, providing exact detector location for selective maintenance when chamber contamination reaches an unacceptable level. The FSP-851(A) photoelectric detector's unique optical sensing �•� chamber is engineered to sense smoke produced by a wide range of combustion sources. Dual electronic thermistors add 135°F (57°C) fixed-temperature thermal sensing on the FSP- _ 851 T(A) The FSP-851 R(A)is a remote test capabie detector for use with DNR(A)/DNRW duct detector housings. FSP-851(A) m series detectors are compatible with Notifier Onyx and CLIP FSP-851(A) In B210LP(A} Base series Fire Alarm Control Panels(FACPs) FlashScanO(U S. Patent 5,539,389)is a communication proto- _gp00SR(A):6.875"(17 46 cm)diameter col developed by Notifier that greatly increases the speed of _g�4RB(A):6.2'(15.748 cm)diameter communication between analog intelligent devices. Intelligent devices communicate in a grouped fashion. If one of the devices —g�461(A):6.2"(15.748 cm)diameter in the group has new information, the panel's CPU stops the Shipping Wefght:5.2oz. (147g). group poll and concentrates on singie points. The net effect is Operating Temperature range: FSP-85i(A), 0°C to 49°C response speed greater than five times that of earlier designs. (32°F to 120°F). FSP-851 T(A), 0°C to 36°C (32°F to 100°F). Low temperature signal for FSP-851T(A) at 45°F +/- 10°F Features (722°C+/-5.54°C). FSP-851 R(A)installed in a DNR(A)/DNRW, • Sieek, low-profile design. -20°C to 70°C(-4°F to 158°F). • Addressable-analog communication UUULC Listed Velocity Range: 0-4000 ft/min. (1219.2 m/ Stable communication technique with noise immunity. min.),suitable for installation in ducts. • Low standby current. Relative Humidity: 10%-93%noncondensing. • Two-wire SLC connection. Thermal Ratings: Fixed-temperature setpoint 135°F(57°C) • Compatible with FlashScanO and CLIP protocol systerr�s. DETECTOR SPACING AND APPLlCAT10/YS • Rotary, decimal addressing(1-99 on CLIP systems, 1-159 on Notifier recommends spacing detectors in compiiance with FlashScan systems) NFPA 72. In low airflow applications with smooth ceiiing, space • Optlonal remote,single-gang LED accessory. detectors 30 feet (9 144m) fior ceiling heights 10 feet (3.148m) • Dual LED design provides 360°viewing angie. and higher For specific information regarding detector spacing, • Visible bi-color LEDs blink green every time the detector is P�acement, and special applications refer to NFPA 72. System addressed, and iliuminate steady red on alarm (FlashScan Smoke Detector Application Guide, document A05-1003, is systems only). available at systemsensor.com • Remote test feature from the panel. ELECTRIEAL SPECIFICATIONS • Walk test with address display (an address on 121 will blink Voltage Range: 15-32 volts DC peak. the detector LED� 12-[pause]-1(FfashScan systems only). Standby Current(max. avg.): 300uA @ 24VDC (one commu- • Built-in functional test switch activated by external magnet. nication every five seconds with LED enabled) • Built-in tamper-resistant feature. LED Current(max.):6.5mA @ 24 VDC("ON") • Sealed against back pressure. • Constructed of off-white fire-resistant plastic, designed to �nstallation commercial standards,and offers an attractive appearance. • 94-5V plastic flammabi(ity rating. FSP-851(A) plug-in detectors use a separate base to simpiify SEMS screws for wiring of the separate base. instailation, service, and maintenance. A special tool allows � maintenance personnel to plug in and remove detectors without • Optional relay, isotator, and sounder bases. using a ladder Mount base(all base types)on an electrical backbox which is at Specifications least 1 5" (3.81 cm) deep. For a chart of compatibVe junction Sensitivity:0.5%to 2.35%per foot obscuration boxes,see DN-60054 Size:2.1" (5.3 cm)high; base determines diameter NOTE: 1) Because of inherent supervision provided by ihe SLC loop, end-of-line resistors are not required. Wiring 7-taps" or —B210LP(A):6 1" (15.5 cm)diameter branches are permrtted for Style 4 (Class 'B) wiring. 2) When —8501(A):4 1"(10 4 cm)diameter using relay or sounder bases, consuft the ISO-X(A) installafion —6200S(A):6.875"(17 46 cm)diameter. DN-6935:D•12/U82011—Page 1 of 2