12-13716 - Laserfiche WebLink

Browse Search

• Maximum current charge. 1.5 A. $tandards and Codes • Maximum battery capacity' 18 AH. The FCP�-24S6 and FCPS-24S8 comply with the following standards: Appiications • NFPA 72 National Fire Alarm Code. Example 1: Expand notification appiiance power an additional . UL 864 Standard for Control Units for Fire Afarm Systems 6.0 A (FCPS-24S6) or 8.0 A (FCPS-24S8). Use up to four (NAC expander mode) Class B (Sryle Y) outputs or four Class A (Sryle Z) outputs . UL i481 Power Supplies for Fire Alarm Systems (using ZNAC-4) For example,the FACP notification appliance circuits will activate the FCPS when reverse-polarity activation occurs. Trouble conditions on the FCPS are sensed by the agency L'estings and Approvafs FACP through the notification appiiance circuit. These listings and approvals appiy to the modules specified in Example 2: Use the FCPS to expand auxiliary regulated 24- this document. In some cases,certain modules or applications volt system power up to 4 0 A (FCPS-24S6) or up to 6.0 A may not be listed by certain approval agencies, or fisting may (FCPS-24S8) Both resettable and non-resettabie power be in process. Consult factory for Iatest iisting status. options are avaifabie. Resettable outputs are created by con- . UL Listed: S635,S674 necting the resettable output from the FACP to one or both of ULC Listed:S635(FCPS-24S6C& FCPS-24S8C} the FCPS inputs. � Example 3: Use addressable control modules to activate the • CSFM Approved: 7315-0028:225 FCPS instead of activating it through the FACP notification ' MEA: 299-02-E appliance circuits.This typically allows for mounting the FCPS • FM Approved at greater distances` away from the FACP while expanding system architecture in various applications. Ordering Information For example, an addressable control module is used to acti- FCPS-24S6: 6.0 A, 120 VAC remote charger power supply. vate the FCPS,and an addressable monitor module is used to Inciudes main printed circuit board, transformers, enclosure sense FCPS troubie conditions. Locai au�uliary power output ��5"H x 14.5"W x 2.75"D[cm:38 1 H x 36.83W x 6.985D]),and from the FCPS provides power to the addressable control installation instructions. module. FCPS-24S6C: Same as above, ULC-listed. 'NOTE:Addressable FACPs are capable of locating control and monitor modules at distances of up to 12,500 feet(3,810 meters). FCPS-24S6R: Same as FCPS-24S6 with red enciosure. FCPS-24S6E: 6 0 A, 240 VAC remote charger power supply. Sync Foilower/Generator Note Includes main printed circuit board, transformers, enclosure In some installations, it is necessary to synchronize the flash ��5"H x 14.5"W x 2.75"D[cm:38.1 H x 36.83W x 6.985D]),and timing of all strobes in the system for ADA compliance. �nstallation instructions. Strobes accomplish this by monitoring very short timing pulses FCPS-24S8: 8.0 A, 120 VAC remote charger power supply. on the NAC power which are created by the FACP When Includes main printed circuit board, transformers, enclosure installed at the end of a NAC wire run, the FCPS-24S6/-24S8 (15"H x 14.5"W x 2.75"D[cm:38.1 H x 36.83W x 6.985D]),and can track (i.e. "follow") the strobe synchronization timing installation instructions. pulses on the existing NAC wire run.This maintains the overall FCPS-24S8C Same as above, ULC-listed. system flash timing of the additional strobes attaches to the FCPS. FCPS-24SSR: Same as FCPS-24S8 with red enclosure. When the FCPS-24S6/-24S8 is configured(via DIP switch set- FCPS-24S8E: 8.0 A, 240 VAC remote charger power suppiy. tings) as a"sync follower,"the FCPS's NAC outputs track the Incfudes main printed circuit board, transformers, enclosure strobe synchronization pulses present at the FCPS's sync (15"H x 14 5"W x 2.75"D[cm:38.1 H x 36.83W x 6.985Dj),and input terminal.The pulses originate from an upstream FACP or �nstallation instructions. other power supply. ZNAC-4: Class A(Style Y)NAC option module. When the FCPS-24S6/-24S8 are configured (via DIP switch EOLR-1: 12124 VDC end-of-line relay for monitoring four-wire settings) as a "sync generator," the FCPS's sync input termi- smoke detector power �als are not used. Rather, the FCPS is the originator of the gAT 1270: Battery, 12-volt, 7.0 AH (two required, see BAT strobe synchronization pulses on the FCPS's NAC outputs. In Series data sheet DN-6933) °sync generator"mode,the sync type(System Sensor, Whee- fock,or Gentex)is selectabie via DIP switch settings. PS-1270: Battery, 12-volt, 7.0 AH (two required, see PS Series data sheet DN-1109) System Sensor�and NOTIFIEFt�are registered trademarks of Honeyweli Intemational Inc. C�2009 by Honeywell Intemational Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. 1S0 �oo� This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. ��6� All specifications are subjed to change without notice. QiALITT SrSTEMS MadeintheU.S.A. For more information,contact Nofrfier Phone:(203)484-7161,FAX.(203)484-7118. www.not'rfier.com Page 2 of 2—dn-6927:a•04/30/09