14-15548 - Laserfiche WebLink

Browse Search

(�� l �� '`-%' `�f TRINITY ERD � 5.7 For tile roof installations governed by t e FRSA/TRI 07320/8-05 Installation Manual, Fourth Edition, use is limited to the following. Reference is made to the FRSA/TRI Technical Brief titled "Florida High Wind Roof Tile Self-Adhered Underlayment Requirements as of 02/14/2011"for limitations for self-adh ring underlayments used beneath tile roof systems. TABLE 2:TILE SYSTEM PTiONS PeR FRSA/TRY 07320/8-05 System Underlay Section Reference Product(s) O tion 3.02A 1 Batten Modified Cap Sheet Unilay(e) Svstem One: onl Mechanically Fastened Self-Adhered 5 3.02E Lastobond TU HT,Colphene FR GR Tile,Unsealed or Underlayment Sealed Underlayment Base Layer:ASTM D226,Type II; Sopre- , System No. 30/Self-Adhered G; Modified Sopra-G 6 3.02F Underlayment Top Layer: Lastobond TU HT,Colphene FR GR ' 4 3.02D Self-Adhered Lastobond TU HT,Colphene FR GR Svstem Two: Underlayment Mechanically Fastened Base Layer: ASTM D226,Type II; Sopre- Tile,Sealed No.30/Self-Adhered G; Modified Sopre-G Underlayment System 5 3.02E Underlayment Top Layer: Lastobond TU HT,Colphene FR GR 1 3.02A Modified Ca Sheet Unila e System Four"A": Self-Adhered Adhesive-Set Tile, 4 3.02D Underla ment Colphene FR GR Unsealed or Sealed Base Layer: ASTM D226,Type II; Sopre- Underlayment System 5 3.02E No. 30/Self-Adhered G; Modified Sopra-G Underlayment To La er: Col hene FR GR Svstem Four'�B": 3 3.02C Self-Adhered Coiphene FR GR Adhesive-Set Tile, Underla ment Sealed Underlayment No. 30/Self-Adhered Base Layer: ASTM D226,Type II; Sopra- System 4 3.02D Underlayment G; Modified Sopra-G To La er: Col hene FR GR 6. INSTALLATION: 6.1 Soprema Roof Underlayments shall e installed in accordance with Soprema published installation requirements subject to t e Limitations set forth in Section 5 herein and the specifics noted below. 6.2 Re-fasten any loose decking panels, and check for protruding nail heads. Sweep the substrate thoroughly to remove any dust and debris prior to application, and prime the substrate with Elastocol Stick or Elast col 600c (if applicable). 6.3 Lastobond TU HT Lastobond Shield astobond Pro HT-N Lastobond Shield HT Lastobond Pro HT-S Lastobond Lastobond 195 Lastobond Eco Lastobond Smooth Seal HT Resisto LB1236 Gri -Rite Eave &Valle Prote tor Resisto LB1244 or Col hene FR GR: 6.3.1 Shall be installed in compliance with t e requirements for ASTM D1970 underlayment in FBC Sections 1507 for the type of prepare roof covering to be installed. 6.3.2 For non-tile applications: 6.3.2.1 While priming is optional, Soprema ecommends priming with Elastocol Stick or Elastocol 600c if the final roof cover is not slate for installation within 24 hours. 6.3.2.2 Apply sheet parallel to the roof edge Roll out approximately 10 ft of inembrane and peel back the first 3 ft of release film. 6.3.2.3 Adhere the exposed part to the sub trate and unroll the remaining membrane as far as possible. 6.3.2.4 Once the entire length of inembrane is in place, peel-off the release film diagonally while holding the membrane tight. Firmly r II the membrane into place to achieve a bond. Exterior Research and Design, LLC. Evaluation Report S18010.06.09-R5 Certifcate ofAuthorization#9503 FL2569-R7 Revision 5: 04/30/2014 Page 6 of 8