14-15548 - Laserfiche WebLink

Browse Search

��'�_/ � �� TRINITY ERD 6.3.2.5 Horizontal seams should be minimum 3-inches, configured to shed water. Vertical seams should be 6-inches and staggered not I ss than 2-ft from vertical seams in the course below. All over-granule end-laps shall be s aled using either heat-welding or hot air welding techniques. 6.3.2.6 When installing at slopes above 8:12, oprema recommends back-nailing in the overlap area at the top of the sheet at 12-inch o.c. 6.3.2.7 For Valleys and Ridges: Cut underlay ent into 4 to 6 foot lengths. Peel the release paper and center sheet over valley or ridge. Drape and press sheet into place, working from the center of the valley or ridge in each irection. For valleys, apply the sheet starting at the lowest point and work upward. 6.3.3 For tile applications: 6.3.3.1 Reference is made to FRSA/TRI 07320 8-05 Installation Manual, Fourth Edition, and Table 2 herein, using the instructions noted ab ve as a guideline. 6.3.3.2 For Colphene FR GR in foam-on tile a plications, reference is made to Section 5.5.4 herein for wind resistance limitations. 6.3.3.3 Tile shall be loaded and staged in a m nner that prevents tile slippage and/or damage to the underlayment. 6.4 Unilav(e): 6.4.1 For non-tile a lications or nail-on ba ened tile a lications: 6.4.1.1 Reference is made to FRSA/TRI 0732 8-05 Installation Manual, Fourth Edition, and Table 2 herein. 6.4.1.2 Apply sheet parallel to the roof edg and, starting at the eave with the selvedge-edge upslope, mechanically attach the 5-in wide selvedge-edge to the wood deck with nails and tin caps or round cap-nails spaced 36- nch o.c. Apply the second course in a water-shedding manner with self-adhering side-laps. igorous hand or motorized roller pressure is applied to the self-adhering laps to ensure a wat rtight application. 6.4.1.3 Vertical seams should be 6-inches an staggered not less than 2-ft from vertical seams in the course below. All over-granule en -laps shall be sealed using either heat-welding or hot air welding techniques. 6.4.1.4 Tile (if applicable) shall be loaded and staged in a manner that prevents tile slippage and/or damage to the underlayment. 6.4.2: For foam-on tile applications: 6.4.2.1 Reference is made to FRSA/TRI 0732 /8-05 Installation Manual, Fourth Edition, and Table 2 herein. 6.4.2.2 Apply sheet parallel to the roof edg and, starting at the eave with the selvedge-edge upslope, mechanically attach the 5-inch wide selvedge-edge to the wood deck Soprafix Polymer Batten Bar (PBB) or Sopr fix Metal Batten Bar (MBB) with Soprema #15-EL fasteners spaced 6-inch o.c. Apply th second course in a water-shedding manner with self- adhering side-laps. Vigorous hand or motorized roller pressure is applied to the self- adhering laps to ensure a watertight a plication. 6.4.2.3 Vertical seams should be 6-inches a d staggered not less than 2-ft from vertical seams in the course below. All over-granule e d-laps shall be sealed using either heat-welding or hot air welding techniques. 6.4.2.4 Tile (if applicable) shall be loaded an staged in a manner that prevents tile slippage and/or damage to the underlayment. Exterior Research and Design, LLC. Evaluation Report 518010.06.09-R5 Certifcate ofAuthorization#9503 FL2569-R7 Revision 5: 04/30/2014 Page 7 of 8