|
i
<br /> i.� �� � �
<br /> y �`.......-
<br /> �``��i TRINITY�ERD
<br /> elevated pressure criteria. Commonly used methods are RAS 117 and FM LPDS 1-29. Assemblies marked with an asterisk* carry the limitations set forth in Section
<br /> 2.2.1.5.1(a)of FM LPDS 1-29 for Zone 2/3 enhancements.
<br /> 9. For fully bonded assemblies, the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC
<br /> Chapter 16, and no rational analysis is permitted.
<br /> 10. For mechanically attached components over existing decks, fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall
<br /> review the data for comparison to the minimum requirements for the system. Testing and analysis shall be in accordance with TAS 105 or ANSI/SPRI FX-1.
<br /> il. For existing substrates in a bonded recover installation, the existing roof surface shall be examined for compatibility and bond pertormance with the selected adhesive, and
<br /> the existing roof system shall be capable of resisting project design pressures on its own merit to the satisfaction of the AHJ, as documented through field uplift testing in
<br /> accordance with ASTM E907, FM LPDS 1-52 or ANSI/SPRI IA-1.
<br /> 12. For Recover Applications using System Type D, the insulation is optional. Alternatively, min. 0.5-inch EnergyGuard High Density Roof Fiberboard, EnergyGuard RH HD
<br /> Polyiso Insulation, EnergyGuard HD Polyiso Insulation or EnergyGuard HD Pius Polyiso Insulation or min. 0.25-inch DensDeck, DensDeck Prime or SECUROCK Gypsum-Fiber
<br /> Roof Board or SECUROCK Glass-Mat Roof Board, or min. 1.0-inch EnergyGuard POLYISO INSULATION, EnergyGuard RA, EnergyGuard RH, EnergyGuard RN or EnergyGuard
<br /> Ultra may be used as a separator board, preliminarily attached prior to base sheet installation. The existing roof system shail be suitable for a recover application.
<br /> 13. Unless otherwise noted, refer to the following references for bonded base, ply or cap sheet applications.
<br /> Reference Layer Material Application
<br /> gp-qq Base: GAFGLAS#75 Base Sheet,Tri-Ply N75 Base Sheet,GAFGLAS ii80 Ultima Base Sheet
<br /> (Base/Ply sheeu,Asphalt-Applied) Ply: GAFGLAS Ply 4,Tri-Piy Ply 4,GAFGLAS FlexPly 6,GAFGLAS FlexPly 6 SL Hot asphalt at 25 Ibs/square.
<br /> MatrixTM'302 SBS Membrene Adhesive
<br /> BP-CA Base: GAFGLAS#75 Base Sheet,Tri-Ply#75 Base Sheet (formerly known as TOPCOAT MATRIX 102
<br /> (Base/Ply sheets,Cold-Applied)
<br /> 565 MembraneAdhesive)at 1.5 gal/sq.
<br /> B-LL Base: GAFGLAS Stretavent Eliminator Perforated Venting Base Sheet Loose laid
<br /> Base or Ply: Ruberoid 20,Ruberoid Dual Smooth,Ruberoid MOP Smooth,Ruberoid MOP Smooth 1.5,Ruberoid MOP Plus Smooth
<br /> SBS-AA Ruberoid Dual Smooth,Ruberoid 30,Ruberoid 30 FR,Ruberofd EnergyCap 30 FR SBS Membrane,Ruberoid Dual FR,
<br /> (585,Asphalt-Applied) Cap: Ruberoid MOP Smooth,Ruberoid MOP Smooth 1.5,Ruberoid MOP Plus Smooth,Ruberoid MOP 170 FR,Ruberoid MOP Hot asphalt at 25 Ibs/square.
<br /> Grenule,Tri-Ply SBS Modified Bitumen Membrane,Intec Flex PRF,RoofMatch SBS Modified Granular,Ruberoid MOP FR,
<br /> Ruberoid MOP Plus,Ruberoid EnergyCap MOP FR
<br /> SBS-CA Base or Ply: Ruberoid 20 Matrix'"'302 SBS Membrane Adhesive
<br /> (SBS,Cold-Applied,MatrixTM'102 585 Ruberoid 30 FR,Ruberoid EnergyCap 30 FR SBS Membrane,Ruberoid MOP 170 FR,Ruberoid MOP FR,Ruberoid (jormerly known as TOPCOAT MATRIX 102
<br /> Membrane Adhesive) �ap� EnergyCap MOP FR SBS Membrane Adhesive)at 1.5 gal/sq.
<br /> Matrix'"101 Premium 585 Membrane
<br /> SBS-CA-1 Base: Ruberoid 20 or Ruberoid MOP Smooth 1.5 Adhesive(fo�me�ly known os TOPCOAT
<br /> (SBS,Cold-Applied,MatrixTM 101 MATRIX MoJorbond Modified Bitumen
<br /> Premium SBS Membrene Adhesive) �ap: Ruberoid 30 FR,Ruberoid EnergyCap 30 FR SBS Membrane,Ruberoid MOP FR,Ruberoid EnergyCap MOP FR Membrone Adhesive)at 1.5—2.0 I
<br /> gal/square i
<br /> Base or Ply: Ruberoid SBS Heat-Weld 25,Ruberoid SBS Heat-Weld Smooth
<br /> SBS-TA Ruberoid SBS Heat-Weld Grenule,Ruberoid SBS Heat-Weld 170 FR,Ruberoid SBS Heat-Weld Plus,Ruberoid SBS Heat-
<br /> (SBS,Torch-Applied) Cap: Weld Plus FR,Ruberoid EnergyCap SBS Heat-Weld Plus FR
<br /> Base or Ply: Ruberoid TORCH Smooth,Tri-Ply TP-4 Torch applied
<br /> APP-TA Ruberoid TORCH Grenule,Tri-Ply TP-4G,Ruberoid TORCH 180,RoofMatch APP Modified Granular,Ruberoid TORCH FR,
<br /> (APP,Torch-Applied) �ap' Ruberoid EnergyCap APP 250 FR,Ruberoid EnergyCap TORCH Grenule FR,Ruberoid EnergyCap TORCH Plus FR
<br /> SBS-SA(self-adhering) Base or Ply: Liberty SBS Self-Adhering Base/Ply Sheet Self-adhered
<br /> Cap Liberty SBS Self-Adhering Cap Sheet
<br /> 14. "MDP"= Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads. Refer to FBC 1609.1.5 for determination of design wind I
<br /> loads.
<br /> Exterior Research and Design,LLC.d/b/a Trinity�ERD Evaluation Report 01506.11.04-R12 for FL5680-R12
<br /> Certificate of Authorization#9503 Revision 12: 04/25/2014
<br /> Prepared by: Robert Nieminen,PE-59166 Appendix 1,Page 3 of 61
<br />
|