|
I
<br /> � I
<br /> �
<br /> , SYSTEM_SPECIFIC C403.4.3.4 Mechanical Temperature reset by representative building
<br /> loads in pumping systems for chiller and boiler � � � ,
<br /> systems>300,000 Btu/h.
<br /> SYSTEM_SPECIFIC C403.4.4 Mechanical Fan systems with motors>=7.5 hp associated
<br /> with heat rejection equipment to have capability to � � �
<br /> operate at 2/3 of full-speed and auto speed
<br /> controls to control the leaving fluid temperature or
<br /> condensing temp/pressure of heat rejection , i
<br /> device. I
<br /> Plan Review C406 Project Plans,specifications,and/or calculations provide � � � � '
<br /> all information with which compliance can be �,
<br /> determined for the additianal energy efficiency �
<br /> package options. i
<br /> Plan Review C402.3.2.2 Envelope Skylights in office,storage,automotive service, � � �
<br /> manufacturing,non-refrigerated warehouse,retail
<br /> store,and distribution/sorting area have a ;
<br /> measured haze value>90 percent unless
<br /> designed to exclude direct sunlight.
<br /> �;.��s±�st��,�:,.:;t_z-��^..�.:�;�s��-__ __ `�;.. h..� _�.�..�.m-�� •-�-r-��k�,-��,���-.-s�`�w.��r3-��'"".�,�m._,�a__ _ -
<br /> a�r2,'.t - - - .3.''�'��5�'�'i ��r 9 - __ - i:sb�='"..�'.'-v.�'�''is'�•:�t�� - -
<br /> _�,i;. " -(',Y< " / - _ `�7:':�i�,...� -' �y',v',2;•F
<br /> ��:y^t' �4n... -- ni'�c •l�'u - ..�, ' 1 �/�3 M a w' �r ' - :4r,'
<br /> +.,.�n;-.F'�°; ;:'r''ss-`:t�M:ix' ';fiiK � 2 vr, p �";:�`��'.''H�.''=�;._� ' - =iaf
<br /> '�-.a- '�:x�n '��'•� !"'•�;�,. f2�� r�� �..•�R/li'i„r.Y{ a�*'a� ',�i{'t���3::at_.;t,t.;,.. ;,;a':�i^::,'s,'tii';yN;,"it'..,,�k.'�."y„' '::a.,,;
<br /> - -t:�'N�'."__�N,.t__....'„�.:'.�"rs.�;d«�y�h�_.,'�;:.e..=�.Y_i:�.�:��'�.�.':<,x-.:, scg��.:.t. Fr'{-:rx. 'Y�-:e .er+:J..o-.,..-a;...'-:��� - _ ...1-i:y^,'-�yyw�3:..: .-.3iSi:
<br /> 'a,.�l�,.S.u...��v-.��x.��sv_=,..�.__._._....-_.._._�..'s_x�+..__u.>_..�_�'.,�t,`3"aG.�
<br /> Air Leakage C402.4.1,C402.4.2 Envelope The building envelope contains a continuous air � � �
<br /> barrier that is sealed in an approved manner and �
<br /> either constructed or tested in an approved
<br /> manner. Air barrier penetrations are sealed in an ,
<br /> approved manner. '
<br /> Air Leakage C402.4.3,C402.4 4 Envelope Factory-built fenestration and doors are labeled � � � �
<br /> as meeting air leakage requirements. ,
<br /> Air Leakage C402.4.1 1 Envelope All sources of air leakage in the building thermal � � �
<br /> envelope are sealed,caulked,gasketed,weather �
<br /> stripped or wrapped with moisture
<br /> vapor-permeable wrapping material to minimize i
<br /> air leakage. '
<br /> Air Leakage C402.4.6 Envelope Weatherseals installed on all loading dock cargo � � � �
<br /> doors.
<br /> Air Leakage C402.4.8 Envelope Recessed luminaires in thermal envelope to limit � � �
<br /> infiltration and be IC rated and labeled.Seal
<br /> between interior finish and luminaire housing.
<br /> Fenestration C303.1.3 Envelope Fenestration products rated in accordance with � � � I
<br /> NFRC. ,
<br /> Fenestration C303.1.3 Envelope Fenestration products are certified as to � � � ;
<br /> performance Iabels or certificates provided. ,
<br /> Insulation C303.2 Envelope Below-grade wall insulation installed per � � � �
<br /> manufacturer's instructions.
<br /> Insulation C303.2 Envelope Slab edge insulation installed per manufacturer's � � � �
<br /> instructions. �
<br /> Insulation C403.2.7,C408.2.8,( Envelope Exterior insulation protected against damage, � � � �
<br /> sunlight,moisture,wind, landscaping and ,
<br /> equipment maintenance activities.
<br /> Insulation C402.4.2.1 Envelope Roof R-value.For some ceiling systems, � � � �
<br /> verification may need to occur during Framing
<br /> Inspection.
<br /> Insulation C303.2 Envelope Roof insulation installed per manufacturers � � �
<br /> instructions. Blown or poured loose-fill insulation '
<br /> is installed only where the roof slope is<=3 in 12. �
<br /> Insulation C402.2.1 Envelope Skylight curbs are insulated to the level of roofs � � � !
<br /> with insulation above deck or R-5. i
<br /> Insulation C303.2 Envelope Above-grade wall insulation installed per � � �
<br /> manufacturer's instructions.
<br /> Insulation C303.2 Envelope Floor insulation installed per manufacturer's � � �
<br /> instructions.
<br /> Insulation C303.1 Envelope Building envelope insulation is labeled with � � � ,
<br /> R-value or insulation certificate providing R-value �
<br /> and other relevant data. �
<br /> Insulation C303.2.1 Envelope Exterior insulation is protected from damage with � � �
<br /> a protective material.Verification for exposed
<br /> foundation insulation may need to occur during
<br /> Foundation Inspection.
<br /> EnergyGauge Summii0 Fla/Com-2014.TAM 2014-1.0 Compliant Software.Effective Date:June 30,2015
<br /> Florida Building Code,Fifth Edition(2014)-Energy Conservation IECC 2012-Total Building Performance Compliance Option
<br /> 1/i l/2017 Page 10 of 13
<br />
|