Laserfiche WebLink
^ <br /> ' <br /> . . <br /> QTRINIVI���-- -- <br /> 5.6 Exposure Limitations: <br /> 5.5.1 Deck-Armor`° Premium Breathable Roof Deck Protection; RouO,no= SBS-Modified All-Purpose <br /> Undedayrnant; Shingle-Mate`" Roof Deck Protection; StonnBafe@ Anchor Sheet; Tiger PaWTM <br /> Roof Deck Protection; VesaShia/d0y Under|ayrnent; Vasa5hia|d@ Fins Resistant Roof Deck <br /> Protection; LibertyTM S8S Self-Adhering Base/Ply Sheet; Rubevuid0D SA Base/Ply Sheet; <br /> StormGuard@ Leak Barrier; UndedRonfr" HT Leak Barrier; VVoatherVVahch@ Leak Barrier; and <br /> Weather VVatch@ XT Leak Barrier shall not be left exposed for longer than 30'dmyo after <br /> installation. <br /> 5.6.2 UndarRoofTm Z Leak Barrier shall not be left exposed for longer than 180-days after <br /> installation. ' <br /> 5.7 For tile roof installations governed by the FRSA/TRI 07320/8-05 Installation Manual, Fourth <br /> Edition, use |s limited ho the following. Reference is made tothe FRS/VTR Technical Brief <br /> titled "Florida High Wind Roof Tile Self-Adhered Undedoyment Requirements as of <br /> 02/14/2011"for limitations for self-adhering underlayments used beneath tile roof systems. <br /> Table 2:Tile System Options per FRSA/TRI 07320/8-05 <br /> System Underlay Section Reference Roof Underlayment(s) <br /> Option <br /> 4 3.02D Two Ply No.30 Two ply Deck-Armor—(Contact Tile <br /> System One: Manufacturer) <br /> Mechanically Self-Adhered <br /> Unsealed or Sealed Underlayment <br /> Underlayment Base Layer:ASTM 226,Type II felt or <br /> System Two: Self-Adhered <br /> Fastened Tile, <br /> Sealed No.30/Self-Adhered Base Layer:ASTM 226,Type 11 felt or <br /> System Top Layer: UnderRoof�2 <br /> System Four"A": 4 Self-Adhered <br /> Unsealed or Sealed No.30/Self-Adhered Base Layer:ASTM 226,Type Il felt <br /> System Four"B Self-Adhered <br /> Sealed <br /> No.30/Self-Adhered Base Layer:ASTM 226,Type II felt <br /> System <br /> 6. INSTALLATION: <br /> 6.1 GAF Roof Undedayments shall be installed in accordance with GAF published installation <br /> instructions subject tothe Limitations set forth in Section 5 herein and the specifics noted <br /> below. - <br /> 6.2 Re-fasten any loose ducking panels, and check for protruding nail heads. Sweep the <br /> substrate thoroughly to remove any dust and debris prior to application, and prime the <br /> substrate (if applicable). <br /> 6.3 Install self-adhering undeHayments when ambient temperatures are minimum 45°F and <br /> rising. <br /> 6'4 All metal surfaces shall be phnnad withTopCoat(D Y4athx`~ 307 Premium Asphalt Primer or <br /> alternate GAF accepted ASTM D41 primer prior to application of self-adhering membranes. <br /> Exterior Research and Dem:gn, LLc' Evaluation Report 0150a'04.08-mS <br /> uerWmcaueofAuxm=rizamuv#msms FL10626-RS <br /> Rmvision5: 11/02/2011 <br /> Page 5mf 11 <br />