18-19692 - Laserfiche WebLink

Browse Search

' . . . \PTFuN11TY �� u ��"{ 6.5 Declk-ArmorTm Premium Breathable Roof Deck PLotection: 6.5.1 Install Deck-Armor TM Premium Breathable Roof Dock Protection in compliance with manufacturer's published Installation instructions and the requirements for ASTM D226, Type I and D wnder|ayments in FBC Sections 1507 for the type of prepared roof covering to be installed. 6.5.2 Fasteners shall be 1-inch diameter plastic-capped corrosion resistant nails or 1-inch diameter plastic-capped, corrosion resistant staples. 6.5.3 Install a leak barrier ufUbertyp° SBS Self-Adhering Base/MySheot; Rubenzid@ SA Base/Ply Sheet; StormGuand@; UndarRoof"m 2; UnderRoof'° HT; Weather VVatch@ or Weather VVatch@ XT at vulnerable leak areas, including but not limited to eaves, valleys, rakes, skylights and dormers. At eaves and valleys, install the leak barrier prior bm installation of Deck-Armor TM Along the rake, install Deck-Armor TM, leaving 6 to 8-inch of the deck exposed, and then install the |eak barrier over the Deck-AnmorT° and exposed decking. At � other area s, install the leak barrier over the Deck-Armor=. ' §.S.4 For tile roof installations: Installation is governed by the FKS/VTRI 07320/8-05 Installation Manual, Fourth Edition. Use is limited to System 1, Option 4, Section 3.02D in place of the"No. 30"felt. The"starter strip" and "full-width-sheet" referenced therein shall be proportionate to the width of the Deck-Armor" product. 6.5.5roof installations: ' 6.5'5.1 Standard Installation with Single Layer; roof slope�> 4:12 Starting at the eava, fasten the eave edge and 6-inch wide end-laps 6-inch o.c. Fasten in the field of the roll 12-inoho.o. in two, equally spaced, staggered center rows. ' Continue ups|ope in similar manner, maintaining minimum 3-inch side-laps and minimum 6-inch end-laps. Fasten 6-inch o.c. in the laps and 12-inch o.c. in two, equally spaced, staggered center rows in the field. Ensure all end laps are staggered at least 3-feetapart. 6.5.5'2 Standard Installation with Double Layer; 2:12�< roof slope < 4:12 Starting at the eave, fasten the eavu edge and 6-inch wide end-laps 6-inch o.c. Fasten in the field of the roll 12-incho'o. in two, equally spaced, staggered center rows. Continue ups|opo in similar manner, with minimum 28.5-inch side'|opsand minimum 6- inch end-laps. Fasten 6-inch o.c. along the low edge and end laps and 12-incho'c. in two, equally spaced, staggered center rows in the field. Ensure all end laps are staggered at least 3-feet apart. 6.6 Tiger PawTm Roof Deck Protection: 6.6.1 Install Tiger Paw`° Roof Deck Protection in compliance with manufacturer's published installation instructions and the-requirements for ASTM D226, Type I and II underlayments in . FBC Sections 1507 for the type of prepared roof covering to be installed. � 6.6.2 Fasteners shall be 1-inch diameter plastic-capped corrosion resistant nails or 1-inch diameter plastic-capped, corrosion resistant staples. | 6.6.3 Install a leak barrier ofUbertV" SBS Self-Adhering Base/Ply Sheet; Rubaroid@ SA Base/Ply Sheet; StwrmGuard@; UnderRoqF" 2; UnderRooFm HT; Weather VVatch@ or Weather ' VVatchO %T at vulnerable leak areas, including but not limited to eaves, valleys, rakes, skylights and dormers. At eaves and valleys, install the leak barrier prior to installation of Tiger Paw`". Along the rake, install Tiger PaWTM, leaving 6 to 8-inch of the deck exposed, and than install the leak barrier over the Tiger Paw`= and exposed decking. At other areas, install the leak barrier over the Tiger Paw°". Exterior Research and Deaimm, LLC' Evaluation Report 01506'04.08-115 Certificate �w�m*�a w* FL10626-RS �� ' Revision 5: za/02/2011 Page 6mf 11