Laserfiche WebLink
^ <br /> . ^ <br /> . -~-~, <br /> \ / <br /> ��� <br /> �� 0 ��D�0U U |��^w~ <br /> 6'S VersaShield' Underlayment or VersaShielldO Fire Resistant Roof Deck Protection: <br /> 6.9.1 Install VersaShie|d@ UndedaymentorVersaShie|dVg Roe-Resistant Roof Deck Protection in <br /> compliance with manufacturer's published installation instructions and the requirements for <br /> AETIVI D226, Type I and II, ASTM D4869 orASTM D6757 undedayments in FBC Sections <br /> 1507 for the type of prepared roof cover to be installed. A double layer is required for <br /> 2:12 < roof slope < 4:12. Nohammnertncksor staples are permitted <br /> 6.9.2 Install a leak barrier mfUbedY`° SBS Self-Adhering Base/MySheet; Rubenoid@ SA Base/Ply <br /> Sheet; StonmGuanJ@; UndmrRooF" 2; UnderRoofT° MT; Weather VVatch@ or Weather <br /> VVatch@ XT at vulnerable leak areas, Including but not limited to eaves, valleys, rakes, <br /> skylights and dormers. At eaves and valleys, install the leak barrier prior to installation of , <br /> Versa5h|e|dg. Along the rake, install VersaShie|d@ leaving 6to8-inchuf the deck exposed, <br /> and than install the leak barrier over the VexsaBhie|d@ and exposed decking. At other areas, <br /> install the leak barrier over the VarsaShie|d=. <br /> 6.10 Liberty"" SBS Self-Adhering Base/Pik Sheet or Ruberoid SA Base/Ply Sheet: <br /> 6.10.1 Install Ubertyp14 SBS Self-Adhering Base/Ply Sheet or Ruberoid SA Base/Ply Sheet in <br /> compliance with manufacturer's published installation instructions and the requirements for <br /> ASTM D1970 undar|aymnents in FBC Sections 1507 for the type of prepared roof covering to <br /> be Installed. <br /> 6.10'2 The minimum and maximum roof slopes are 1/2:12 and 6:12, respectively. Back-nailing is <br /> required when slope is 1:12 or greater. Back-nailing shall consist of minimum 1-inch square � <br /> or round cap nails spaced 18"o.c. within 3-inch aide laps. <br /> 6'1O.3 <br /> For direct-bond to deck applications plywood shall be primed withTupCoat@ Mathx`° 307 ' <br /> Premium Asphalt Primer oralternate GAF accepted ASTM D41 primer at 92 to -3/4 gallon per <br /> square. <br /> Prior to removal of release 0nn, align shoats properly starting at the low-point of the roof <br /> (mave) with the selvage edge ups|opo and for minimum 2-Inch overhang at eaves and rakes. <br /> Roll out sheet and allow to "re|ax' for min. 30 minutes' Remove the lower piece of release <br /> film and bond to substrate and fold the overhanging 2-inch over the eavw and nail into place <br /> 12" o.c. Remove the top piece of release film and bond to substrate. Install primed drip <br /> edgoandtayten to meet FBC Chapter 1Gwind load requirements. Install 1/8-inch troweling <br /> ofTnpCoat@ Matrio`m 201 Premium SBS Hashing Cement over drip edge. <br /> Continue upo|opm in a similar manner, maintaining [nin|rnumn 3-inch side-laps and minimum <br /> 6-Inch end-laps. Ensure all end laps are staggered at least 18-inch apart. <br /> Use a weighted lawn or linoleum roller to anouna complete adhesion to the substrate. Use m <br /> hand roller to Mnn|y bond side and end laps. <br /> 6.10.4 For non-tile aimlications, to mechanically attached anchor sheet: i <br /> Install ASTM D226, Typo ]I halt in accordance with codified requirements or5toomSahs@ <br /> Anchor Sheet in accordance with Section 6'6. <br /> Install LibertyTM SBS Self-Adhering Base/Ply Sheet or Ruberoid SA Base/Ply Sheet over the <br /> mechanically attached anchor mheetas noted above. <br /> ` <br /> Exterior Research and Design, LLC. Evaluation Report 01506.04.08-115 <br /> Certificate ofAuthorizamon#9503 FL10626-RS <br /> Revision S: a1/02/2m11 <br /> Page 8mn11 <br />