18-19692 - Laserfiche WebLink

Browse Search

1� TRINITY I ER® 6.11 StorrnGuardo Leak Barrier: 6.11.1 Install StormGuardp Leak Barrier in compliance with manufacturer's published installation instructions and the requirements for ASTM D1970 underlayments in FBC Sections 1507 for the type of prepared roof covering to be installed. 6.11.2 Back-nailing is required. Back-nailing shall consist of minimum 1-inch square or round cap nails spaced 18"o.c. within 3-inch side laps. 6.11.3 For non-tile applications, direct to deck: Prior to removal of release film, align sheets properly starting at the low-point of the roof (eave) with the selvage edge upslope and for minimum 2-inch overhang at eaves and rakes. Remove the lower piece of release film and bond to substrate and fold the overhanging 2- inch over the eave and nail into place 12" o.c. Remove the top piece of release film and bond to substrate. Install primed drip edge and fasten to meet FBC Chapter 16 wind load requirements. Install 1/8-inch troweling of TopCoat@ MatrixTm 201 Premium SBS Flashing Cement over drip edge. Continue upslope in a similar manner, maintaining minimum 3-inch side-laps and minimum 6-inch end-laps. Ensure all end laps are staggered at least 18-inch apart. Use a hand roller to firmly bond side and end laps. 6.11.4 For non-tile applications, to mechanically attached anchor sheet Install ASTM D226, Type II felt in accordance with codified requirements or StormSafe@ Anchor Sheet in accordance with Section 6.6. Install StormGuardp Leak Barrier over the mechanically attached anchor sheet as noted above. 6.12 Underikoof m 2 Leak Barrier: 6.12.1 Install UnderRoof"m 2 Leak Barrier in compliance with manufacturer's published installation instructions and the requirements for ASTM D1970 underlayments in FBC Sections 1507 for the type of prepared roof covering to be installed. 6.12.2 The minimum and maximum roof slopes are 2:12 and 12:12, respectively. Back-nailing is required when slope is 4:12 or greater. Back-nailing shall consist of minimum 1-inch square or round cap nails spaced 12"o.c. within 4-inch side laps. 6.12.3 For tile roof installations: Reference is made to FRSA/TRI 07320/8-05 Installation Manual, Fourth Edition, and Table 2 herein, using the instructions noted herein as a guideline. Tile shall be loaded and staged in a manner that prevents tile slippage and/or damage to the underlayment. 6.12.4 For non-tile applications, direct to deck: Prior to removal of release film, align sheets properly starting at the low-point of the roof (eave) with the selvage edge upslope and for minimum 2-inch overhang at eaves and rakes. Remove the lower piece of release film and bond to substrate and fold the overhanging 2- inch over the eave and nail into place 12" o.c. Remove the top piece of release film and bond to substrate. Install primed drip edge and fasten to meet FBC Chapter 16 wind load requirements. Install 1/8-inch troweling of TopCoat@ MatrlXTm 201 Premium SBS Flashing Cement over drip edge. Continue upslope in a similar manner, maintaining minimum 4-inch side-laps and minimum 6-inch end-laps. Ensure all end laps are staggered at least 3-feet apart. End laps shall be sealed with a 1/16th to 1/8th inch thick trowel application of TopCoat@ MatrixTm 201 Premium SBS Flashing Cement. Exterior Research and Design, LLC. Evaluation Report 01506.04.08-115 Certificate of Authorization#9503 FL10626-R5 Revision 5: 11/02/2011 Page 9 of 11