18-20581 - Laserfiche WebLink

Browse Search

Insulation 5.8.1.7 Envelope Exterior insulation protected against damage, sunlight,moisture,wind,landscaping and equipment maintenance activities. HVAC 6.4.3.7 Mechanical Freeze protection and snow/ice melting system sensors for future connection to controls. Air Leakage 5.4.3.1 Envelope Continuous air barrier is wrapped,sealed, ❑ caulked,gasketed,and/or taped in an approved manner,except in semiheated spaces in climate zones 1-6. Air Leakage 5.4.3.2 Envelope Factory built and site-assembled fenestration and E _ doors are labeled or certified as meeting air leakage requirements. Fenestration 5.8.2.1,5.8.2.3. Envelope Fenestration products rated(U-factor,SHGC,and 5.8.2.4,5.8.2.5 VT)in accordance with NFRC or energy code defaults are used. Fenestration 5.8.2.2 Envelope Fenestration and door products are labeled,or a signed and dated certificate listing the U-factor, SHGC,VT,and air leakage rate has been provided by the manufacturer. -10 El SYSTEM—SPECIFIC 7.4.4.1 Mechanical Temperature controls installed on service water ' heating systems(<=120A°F to maximum temperature for intended use). SYSTEM—SPECIFIC 7.4.4.2 Mechanical Automatic time switches installed to automatically 1:1 El switch off the recirculating hot-water system or heat trace. SYSTEM—SPECIFIC 7.4.6 Mechanical Heat traps installed on non-circulating storage El El El water tanks. HVAC 6.4.1.4,6.4.1.5 Mechanical HVAC equipment efficiency verified.Non-NAECA El El El HVAC equipment labeled as meeting 90.1. SYSTEM—SPECIFIC 6.4.1.5.2 Mechanical PTAC and PTHP with sleeves 16 in.by 42 in. labeled for replacement only. HVAC 6.4.3.4.1 Mechanical Stair and elevator shaft vents have motorized El El ❑ dampers that automatically close. HVAC 6.4.3.4.2,6.4.3.4.3 Mechanical Outdoor air and exhaust systems have motorizedEl 1:1 ❑ dampers that automatically shut when not in use and meet maximum leakage rates.Check gravity dampers where allowed. HVAC 6.4.3.4.5 Mechanical Enclosed parking garage ventilation has automatic contaminant detection and capacity to stage or modulate fans to 50%or less of design capacity. HVAC 6.6.3.2.1 Mechanical DX cooling systems>=75 kBtu/h(>=65 kBtu/h ❑ 0 El effective 112016)and chilled-water and evaporative cooling fan motor hp>=A''Y4 designed to vary indoor fan airflow,as a function of load and comply with operational requirements. HVAC 6.4.4.1.1 Mechanical Insulation exposed to weather protected from damage.Insulation outside of the conditioned space and associated with cooling systems is vapor retardant. HVAC 6.4.4.1.2 Mechanical HVAC ducts and plenums insulated. Where ducts ❑ or plenums are installed in or under a slab, verification may need to occur during Foundation Inspection. HVAC 6.4.4.1.3 Mechanical HVAC piping insulation thickness. Where piping is installed in or under a slab,verification may need to occur during Foundation Inspection. HVAC 6.4.4.2.1 Mechanical Ducts and plenums sealed based on static El 1:1 El pressure and location. SYSTEM—SPECIFIC 6.4.4.2.2 Mechanical Ductwork operating>3 in.water column requires air leakage testing. SYSTEM—SPECIFIC 6.5.2.1 Mechanical Zone controls can limit simultaneous heating and Q El ❑ cooling and sequence heating and cooling to each - zone. SYSTEM—SPECIFIC 6.5.2.2.2 Mechanical Two-pipe hydronic systems using a common distribution system have controls to allow a deadband>=15 A°F,allow operation in one mode for at least 4 hrs before changeover,and have rest controls to limit heating and cooling supply temperature to<=30 A°F. EnergyGauge Summit®Fla/Com-2017.TAM 2017-1.0 Compliant Software.Effective Date:Dec 31,2017—- Florida Building Code,Sixth Edition(2017)-Energy Conservation ASH RAE 90.1-2013-Prescriptive Compliance Option 7/6/2018" Page"12 of 21