Laserfiche WebLink
' <br /> � <br /> ` <br /> ONEMOletc. <br /> BB 'Bond to Mechanically Attached Base Laver: <br /> Lastobond Shield, Lastobund Pro HT-N, RE8STO SA SMOOTH PLY40, Laetobond Shield HT, Lastmbund Pro HT-S, <br /> EnvhnShieh, Lastpbond TU HT, Lustobond Eaves Protection Sheet, Lastobun6 195, Lastoboud ECO, RESIS[Q <br /> LB1236, Grip-Rite Eave & Valley Protector, RES|S7O L81244, Lastnbond3mooth Seal HTm/ Co|phene FRGR <br /> applied to: <br /> > ASTMD226,Type/orU felt;Sop,a-G;Modified Sopra'G. <br /> For installations under{nechan|caUV attached prepared roof coverings,base layer shall be attached per minimum <br /> codified requirements. For installations under foam-on tile systems(kasmobond TU HT only), base layer shall be <br /> attached in accordance with P0SA/TRV April 2012(04-12). <br /> 5.6.4 : F8SA/TRy April 2o12(04-12)does not <br /> address wind uplift resistance of all undeMaynment systems beneath foam-on tile systems, where the <br /> un6edayment forms pa�of the bad�ath. Thefn|hmwngvNndup|UtUmitationsapp!ytoundeMaymertsystems <br /> that are not addressed in FRSA/[Rk April 2012 (04-12) and are used in foam-on tile applications. Maximum <br /> Design Pressure is the result of testing for wind load resistance based on allowable wind loads,and reflects the <br /> ultimate passing pressure divided by I (the 2 to 1 margin of safety per FgC 1504'9 has already been applied). <br /> ` Refer toFRSA/TRY April 2012(04'12)orF8C160g for determination of design wind pressures. <br /> #1 <br /> Deck, Min. 15/32'inch plywood to meet project requirements to satisfaction of Authority Having <br /> Jurisdiction. <br /> Primer: (Optional)Elastocol Stick E|ag000\GO0corRESISTO EXTERIOR PRIMER <br /> Undedayment: LogobondTUHTorCm|pheneFRGR,se|f-adhere6' <br /> #3 <br /> Deck/ Structural concrete to meet project requirements to satisfaction of Authority Having <br /> Jurisdiction. <br /> Primer: G|anoxo|6O0c <br /> Undedayment: LostobondTUHTorCo|pheneFRGR,sdf-adheme6. <br /> #3 Maximum Design Pressure=-150.0 PS : <br /> Deck: Min. 15/32'|nch APA-rated BCX plywood (may be installed Eside up) to meet project <br /> requirements tu satisfaction of Authority Having Jurisdiction. <br /> Deck Preparation:Plywood shall be thoroughly cleaned um remove dust and debris that may inhibit adhesion. All <br /> sheathing fasteners shall be driven flush with the surface' All sharp splinters and wood <br /> projections shall beremoved/sanded. <br /> Primer: (Opt|una|)RE3|S7O EXTERIOR PRIMER <br /> Undedayment: LastobondTU'HT, self-adhered, shall be thoroughly u,U using hand roller and/or weighted <br /> roller to ensure there are no voids, and ensure there are no voids/bridging at side and end' <br /> bps. <br /> #4 <br /> Deck Min. 19/32-inch plywood to meet project requirements to satisfaction of Authority Having <br /> Jurisdiction. <br /> Base Sheet: Sopra-G or Modified Sopra-G mechanically attached with nails(FBC 1517.5.1)and tin caps(FBC <br /> 1517.S.2)spaced G-inchn.c.at the 4-inch laps and O'imcho.c.in three(3),equally spaced rows <br /> in the center of the sheet. <br /> Undedayment: LomobondTUHTnr[o}pheneFRGR,self-adhered <br /> 5.6.4.1 All other direct-deck, adhered Soprema underlayment systems beneath foam-on tile systems carry a Maximum <br /> Design Pressure mf-4Spst <br /> ' <br /> NEW ETC,uc Evaluation Report smou0.00.0y'R^2 <br /> o"«fic"te,/Authorization u32,e EDITION(2o17)mcmow-HxxzcvAummom ru569-xx4 <br /> Soprerna Roof unmerlavm*rts nevxmo"x2,m*12/2oxa <br /> Page Smo <br />