Laserfiche WebLink
Typical Wiring <br /> Single or cascaded booster NAC Circuit To next signaling <br /> g NAC Circuit device,booster,or <br /> anywhere on a notification appliance circuit V Y— <br /> EOL resistor <br /> (D CID <br /> NAC output#1 <br /> Existing NAC end-of-line resistors are not required to be Fire Alarm C. N NAC output#2 <br /> installed at the booster's terminals.This allows multiple Control Panel CIDCID <br /> N NAC output#3 <br /> boosters to be driven from a single NAC circuit without the 5 s NAC output#4 <br /> need for special configurations. <br /> Booster Power <br /> Supply <br /> Configuring the Booster for Multiple CC1(S) modules using the <br /> AC Power Fail delay operation* MIRBPS's sense inputs <br /> TB1 Notification appliance circuit(NAC) TB1 Notification appliance circuit(NAC) <br /> NAC 1/+ UL listed NAC1/ + UL listed <br /> AUX1 - g Q a Q EOL 15 kQ AUX1 - a Q a a EOL 15 KW <br /> NAC2/+ Notification appliance circuit(NAC) NAC2/ + Notification appliance circuit NAC <br /> AUX2 - AUX2 - pp (NAC) <br /> NAC3/+ UL listed NAC3/ + UL listed <br /> AUX3 - II Y EOL 15 kf1 AUX3 -f=DuD <br /> EOL 15 KW <br /> NAC4/+ NAC4/ + <br /> AUX4 - AUX4 - <br /> 200 mAAUX + 200 mAAUX <br /> Continuous m - Continuous m <br /> IN + IN + <br /> Sense 1 COM FW - Sense 1 COM FW - <br /> OUT - + OUT EOL 47 K <br /> IN Eff IN + <br /> Sense 2 COM Eff EOL 47 kfl 109 Sense 2 COM Eff - <br /> OUT CC1(S)module[1][3] OUT EOL 47 K <br /> NO o o NO <br /> Trouble COM 87 65 4 3 2 1 Trouble COM o 0 <br /> NC NCR 109 109 <br /> Tg2 +- + +- Tg2 CC1(S)module CC1(S)module <br /> o a� e CT1 Data in from Data out to o 7 6 5 0 4 3 2 1 87 65 4 3 2 1 <br /> module[4] previous device next device <br /> 0 0 or Signature <br /> controller <br /> Data in from previous + + 'The Booster supports AC Power fail delay [3] <br /> device or Signature Data out to of three hours via its trouble contact when <br /> controller next device dip switch SW2-6 is on.All other troubles <br /> are reported to supervising module or panel <br /> without delay via Sense inputs. <br /> Security and access <br /> BPS <br /> TB1 24 V 12 V <br /> NACl/+ Security Security EOL <br /> AUX1 - 24DC12 device device monitoring <br /> NAC2/+ device <br /> AUX2 - <br /> NAC3/+ <br /> AUX3 - <br /> NAC4/+ <br /> AUX4 - <br /> Control panel BPS[1] <br /> Card reader Card reader [Card reader <br /> controller controller ontroller <br /> + + <br /> To next <br /> device <br /> [1] Disable the MIRBPS's ground fault jumper(JP3) or end <br /> Page 3 of 4 n r,1-A s I3 e:7--r K85005-0125 <br /> No). it,, bo klsferi for Issue s <br />