20-1261 - Laserfiche WebLink

Browse Search

FMM-101(A) Mini Monitor Module Temperature range: 327 to 120°F(0°C to 49°C). • Built-in type identification automatically identifies this Humidity range: 10%to 93%noncondensing. device as a monitor module to the panel. Dimensions: 1.3"(3.302 cm) high x 2.75"(6.985 cm)wide x • Powered directly by two-wire SLC loop. No additional 0.65"(1.651 cm)deep. power required. Wire length: 6"(15.24 cm) minimum. • High noise(EMF/RFI) immunity. • Tinned,stripped leads for ease of wiring. FZM-1(A) Interface Module • Direct-dial entry of address:01 —159 on FlashScan loops; . Supports compatible two-wire smoke detectors. 01 —99 on CLIP loops. • Supervises IDC wiring and connection of external power source. 3 1415 0 1 ADDRESS 0 High noise(EMF/RFI)immunity. 3 126� . 3 3 SEMS screws with clamping plates for ease of wiring. 114 LOOP0� . 4 Direct-dial entry entry of address: 01 —159 on FlashScan 15 5 loops, 01—99 on CLIP loops. 87 87 LED flashes during normal operation; this is a program- TENS ONES mable option. • LED latches steady to indicate alarm on command from control panel. Y The FZM-1(A) Interface Module is intended for use in intelli- O O U gent, addressable systems, where the individual address of O each module is selected using built-in rotary switches. This °Q module allows intelligent panels to interface and monitor two- wire conventional smoke detectors. It transmits the status (normal, open, or alarm) of one full zone of conventional detectors back to the control panel. All two-wire detectors being monitored must be UL compatible with the module. The FMM-101(A) Mini Monitor Module can be installed in a The FZM-1(A) can be used to replace MMX-2(A) modules in single-gang junction directly behind the monitored unit. Its existing systems. small size and light weight allow it to be installed without rigid FZM-1(A) APPLICATIONS mounting. The FMM-101(A) is intended for use in intelligent, two-wire systems where the individual address of each mod- Use the FZM-1(A) to monitor a zone of two-wire smoke ule is selected using rotary switches. It provides a two-wire detectors. The monitored circuit may be wired as an NFPA initiating device circuit for normally-open-contact fire alarm Style B (Class B) or Style D (Class A) Initiating Device Cir- and security devices. The FMM-101(A) can be used to cuit.A 3.9 K Ohm End-of-Line Resistor(provided)terminates replace MMX-101(A)modules in existing systems. the end of the Style B or D (class B or A) circuit (maximum IDC loop resistance is 25 Ohms). Install ELR across termi- FMM-101(A)APPLIcAnoNs nals 8 and 9 for Style D application. Use to monitor a single device or a zone of four-wire smoke FZM-1(A) OPERATION detectors, manual fire alarm pull stations, waterflow devices, or other normally-open dry-contact devices. May also be Each FZM-1(A) uses one of the available module addresses used to monitor normally-open supervisory devices with spe- on an SLC loop. It responds to regular polls from the control cial supervisory indication at the control panel. Monitored cir- panel and reports its type and the status (open/normal/short) cuit/device is wired as an NFPA Style B (Class B) Initiating of its Initiating Device Circuit(IDC). A flashing LED indicates Device Circuit. A 47K Ohm End-of-Line Resistor (provided) that the module is in communication with the control panel. terminates the circuit. The LED latches steady on alarm (subject to current limita- tions on the loop). FMM-101(A)OPERATION Each FMM-101(A) uses one of the available module FZM-1(A)SPECIFICATIONS addresses on an SLC loop. It responds to regular polls from Nominal operating voltage: 15 to 32 VDC. the control panel and reports its type and the status (open/ Maximum current draw:5.1 mA(LED on). normal/short)of its Initiating Device Circuit(IDC). Maximum IDC wiring resistance:25 Ohms. FMM-101(A)SPECIFICATIONS Average operating current: 270 NA, 1 communication and Nominal operating voltage: 15 to 32 VDC. 1 LED flash every 5 seconds,3.9k eol. Average operating current: 350 NA, 1 communication EOL resistance:3.9K Ohms. every 5 seconds, 47k EOL; 600 pA Max. (Communicating, IDC Shorted). External supply voltage (between Terminals T10 and Maximum IDC wiring resistance: 1500 Ohms. T11): Maximum IDC Voltage: 11 Volts. DC voltage:24 volts power limited. • Ripple voltage:0.1 Vrms maximum. Maximum IDC Current:450 NA. Current:90 mA per module maximum. EOL resistance:47K Ohms. Temperature range: 32°F to 120°F(0°C to 49°C). Page 2 of 4—DN-6720:E•07/30/2015