4330 20th St (41) - Laserfiche WebLink

Browse Search

EXHAUST AIR OUTSIDE AIR INPUT/OUTPUT SUMMARY (VAV - COOLING/HUMIDIFICATION AHU) EQUIPMENT MOUNTED PANELS 0 BINARY INPUT 0 BINARY OUTPUT 0 ANALOG INPUT Ao ANALOG OUTPUT EQUIPMENT: SOUTH: AHU-1 NORTH: AHU-2 OCUPANCY SCHEDULE: OCCUPIED: 7AM - 6PM M-F (ADJ) UNOCCUPIED: OTHERWISE +HOLIDAYS POINT ID POINT DESCRIPTION 1 SUPPLY FAN STATUS X 2 RETURN/EXHAUST FAN STATUS X 3 EXHAUST DAMPER STATUS X 4 SUPPLY AIR RELATIVE HUMIDITY X 5 FILTER STATUS X 6 SUPPLY AIR SMOKE DETECTOR X 7 RETURN AIR SMOKE DETECTOR X 8 RETURN/EXHAUST AIR RELATIVE HUMIDITY X 9 RETURN/EXHAUST FAN VFD CONTROL POINT ADJ X 10 RETURN/EXHAUST FAN START/STOP X 11 RELIEF EXHAUST DAMPER OPEN/CLOSE X 12 RETURN/EXHAUST FAN STATUS X 13 RETURN/EXHAUST FAN VFD FAULT X 14 RETURN/EXHAUST FAN START/STOP X 15 RETURN/EXHAUST FAN VFD CONTROL POINT ADJ X 16 LIQUID LINE SELENOID VALVE STATUS X 17 LIQUID LINE SELENOID VALVE OPEN/CLOSE X 18 HOT GAS SELENOID VALVE STATUS X 19 HOT GAS SELENOID VALVE OPEN/CLOSE X 20 SPACE RELATIVE HUMIDITY X 21 OUTSIDE AIR DRY BULB X 22 OUTSIDE AIR RELATIVE HUMIDITY X 23 RETURN/EXHAUST AIR DRY BULB X 24 ERW LEAVING SUPPLY AIR DRY BULB X 25 SUPPLY AIR DRY BULB X 26 SUPPLY DUCT STATIC PRESSURE X 27 ENERGY RECOVERY WHEEL START/STOP X 28 ENERGY RECOVERY WHEEL STATUS X 29 ERW ENTERING EXHAUST AIR DRY BULB X 30 ERW LEAVING EXHAUST AIR DRY BULB X 31 OA DAMPER STATUS X 32 DIGITAL SCROLL START/STOP X 33 DIGITAL SCROLL MODULATE X 34 DIGITAL SCROLL STATUS X 35 REVERSING VALVE HEAT/COOL STATUS X 36 REVERSING VALVE HEAT/COOL CHANGEOVER X 37 RETURN DUCT STATIC PRESSURE X 38 SPACE DRY BULB TEMPERATURE X 39 OA DAMPER OPEN/CLOSE X Grand total: 39 30 29 0[—,3] 15 8 23 00 11 T T 2❑ 10 F7] RH T VFD SD 17 ES RETURN/ EXHAUST AIR [28] [3] 27 21 22 24 a Ag O O O T RH T 12 14 H L VFD SUPPLY AIR C9�■C7o GENERAL NOTES: CONTROL CONTRACTOR SHALL PROVIDE WIRING AND INSTALLATION FOR REMOTE MOUNTED CONTROL DEVICES. ALL SETPOINTS SHALL BE ADJUSTABLE. PID CONTROL LOOPS SHALL HAVE PROGRAMMABLE PROPORTIONAL, INTEGRAL AND DERIVATIVE COEFFICIENTS. THE AIR VALVE WILL MODULATE USING A PID CONTROL LOOP. THE ELECTRIC REHEAT CONTROLLER WILL MODULATE USING A SEPARATE PID CONTROL LOOP. PACKAGED ROOFTOP UNIT: SINGLE ZONE, DX COOLING W/ HEAT PUMP, HOT GAS RE -HEAT AND LIQUID SUB COOLING, VARIABLE VOLUME, ECONOMIZER, ROOF MOUNTED AIR HANDLING UNIT. SYSTEM MODES INCLUDE COOLING, DEHUMIDIFICATION, ECONOMIZER AND HEAT PUMP MODE. SCHEDULE FOR OCCUPIED AND UNOCCUPIED CONDITIONS IS AVAILABLE. INCLUDE OPTIMUM START AND SUPPLY TEMPERATURE RESET. ECONOMIZER MODE: IF OUTSIDE AIR TEMPERATURE IS GREATER THAN 45°F, ENTHALPY WHEEL TURNS OFF. DEHUMIDIFICATION MODES: LIQUID SUB -COOLING FOR COOLING AND DEHUMIDIFICATION AND HOT GAS REHEAT FOR LOW DEMAND LOAD AND DEHUMIDIFICATION. EACH CIRCUIT CAN OPERATE IN EACH OF THE THREE MODES INDEPENDENTLY. ZONE THERMORSTATS IN CONJUNCTION WITH BOTH RETURN AIR RH SENSOR AND REPORTED RH FROM ZONE PRESSURE CONTROLLER, WHICHEVER HIS HIGHER, DETERMINE THE MODE OF OPERATION. RTU OPERATES AT 100% OUTSIDE AIR. IF OUTDOOR ENTHALPY SENSOR IS LESS THAN 20.0 BTU/LB (ADJUSTABLE), THE UNIT SHALL GO INTO ECONOMIZER MODE. RTU SUPPLY FAN WITH VFD VARIES AIRFLOW IN UNOCCUPIED MODE. SUPPLY FAN OPERATES AT COSTANT FLOW DURING OCCUPIED MODE. THE RTU EXHAUST FAN WITH VFD MODULATE RETURN/EXHAUST AIR FLOW TO MAINTAIN A DUCT STATIC PRESSURE SET POINT LOCATED TWO-THIRDS OF THE WAY UPSTREAM IN THE MAIN RETURN TRUNK. SUPPLY TEMPERATURE RESET SHALL UTILIZE TRIM AND RESPOND LOGIC WITHIN THE RANGE 55 to 70OF TO MINIMIZE THE AMOUNT OF ZONE RE -HEAT WHEN OPERATING IN COOLING MODE. THE SUPPLY AIR TEMPERATURE RESETS NO MORE FREQUENT THAN AT 5 MIN INTERVAL. WHEN BOTH ZONES CALL FOR HEATING, THE RTU REFRIGERATION SYSTEM OPERATES IN HEAT PUMP MODE WITH THE AIR SUPPLY TEMPERATURE SET AS NECESSARY TO MINIMIZE THE AMOUNT OF ZONE RE -HEAT. ENTHALPY RECOVERY WHEEL (ERW) OPERATES AT CONSTANT SPEED AND TURNS OFF WHEN RTU ENTERS ECONOMIZER MODE AND ERW SUPPLY AIR TEMPERATURE IS LESS THAN 48 OF (ADJ) TO AVOID TOO HIGH ERW SUPPLY AIR TEMPERATURE INCREASE RESULTING IN UNECESSARY MECHANICAL COOLING. ERW ALSO TURNS OFF IF THE RTU EXHAUST FAN SHUTS DOWN. A DIGITAL SCROLL COMPRESSOR MODULATES SYSTEM CAPACITY TO MEET SUPPLY AIR TEMPERATURE SETPOINT. SMOKE DETECTORS SHALL STOP THE FAN WHEN ALARMED. HIGH STATIC PRESSURE SWITCH SHALL STOP THE FAN WHEN ALARMED. 38 20 SPACE SENSOR LOCATED RH SENSORS AS FOLLOWS: RETURN DUCT SPACE (MICROLAB ROOM & QC LAB ROOM) UTILIZE VAV BOX DATA FOR SUPPLY AIR TEMPERATURE RESET RETURN AIR 25 O a T RH SD LIJI.AIC JIAI Il. PROBE 2/3 DOWN DUCT RUN. INPUT/OUTPUT SUMMARY (VARIABLE VOLUME TERMINAL BOX) EQUIPMENT MOUNTED PANELS 0 BINARY INPUT 0 BINARY OUTPUT 0 ANALOG INPUT Ao ANALOG OUTPUT POINT ID POINT DESCRIPTION 1 PRIMARY AIR FLOW STATION X 2 ROOM TEMPERATURE X 3 USER TEMPERATURE ADJUSTMENT X 4 ROOM PRESSURE X 5 RELATIVE HUMIDITY X 6 OCCUPANCY OVERRIDE SWITCH X 7 PRIMARY AIR DAMPER MODULATE X 8 ELECTRIC REHEAT MODULATE (SCR) X 9 DISCHARGE TEMPERATURE X 10 RETURN AIR FLOW STATION X 11 RETURN AIR TEMPERATURE X 12 RETURN AIR DAMPER MODULATE X Grand total: 12 SUPPLY AIR FROM RTU A7 TO RTU ZONE PRESSURE CONTROLLER, TSI RPC30, WITH PRESSURE, TEMPERATURE AND HUMIDITY SENSORS AND TEMPERATURE SETPOINT (ADJ.) AND OCCUPANCY OVERRIDE /a . 11 Aio SUPPLY AIR RETURN AIR GENERAL NOTES: CONTROL CONTRACTOR SHALL PROVIDE WIRING AND INSTALLATION FOR REMOTE MOUNTED CONTROL DEVICES. ALL SETPOINTS SHALL BE ADJUSTABLE. PID CONTROL LOOPS SHALL HAVE PROGRAMMABLE PROPORTIONAL, INTEGRAL AND DERIVATIVE COEFFICIENTS. THE AIR VALVE WILL MODULATE USING A PID CONTROL LOOP. THE ELECTRIC REHEAT CONTROLLER WILL MODULATE USING A SEPARATE PID CONTROL LOOP. OCCUPIED: THERMOSTAT SETPOINT: 70 OF HEATING AND 75' COOLING. VARIABLE VOLUME TERMINAL BOX WITH ELECTRIC REHEAT THE SINGLE DUCT VARIABLE VOLUME TERMINAL UNIT DELIVERS A CONSTANT AIRFLOW TO THE SPACE DURING OCCUPIED MODE TO MEET SPACE LOAD AND ACHIEVE A MINIMUM OF 10 AIR CHANGES, WHICHEVER IS GREATER. THE VAV TERMINAL ELECTRIC REHEAT COILS ARE UNDER CONTROL OF THE ZONE'S PRESSURE CONTROLLER PROVIDED WITH TEMPERATURE SENSOR (THERMOSTAT). HEATING: ON A DECREASE IN SPACE TEMPERATURE BELOW HEATING SETPOINT (ADJUSTABLE), ELECTRIC REHEAT COIL WITH SCR MODULATES TO MAINTAIN TEMPERATURE SETPOINT. THE ZONE REHEAT COILS ARE MONITORED AND THE SUPPLY AIR TEMPERATURE IS INCREASED UNTIL THE REHEAT COIL OF THE ZONE WITH LEAST HEATING LOAD MODULATES OFF WHILE MAINTAINING SPACE TEMPERATURE SET POINT. REHEAT FOR OTHER ZONE ALSO MODULATE ACCORDINGLY TO MAINTAIN TEMPERATURE SETPOINT. COOLING: ON AN INCREASE IN SPACE TEMPERATURE ABOVE COOLING SETPOINT (ADJUSTABLE) THE RTU SYSTEM SHALL BE SIGNALED TO ADJUST THE COOLING AIR SUPPLY TEMPERATURE SETPOINT. ZONE REHEAT SHOULD BE OFF. A TEMPERATURE CONTROL DEADBAND OF +/- 5°F (ADJ) SHALL BE SET TO ELIMINATE EXCESSIVE CYCLING OF HEATING AND COOLING. RETURN AIR DAMPER: THE AIRFLOW DIFFERENTIAL BETWEEN SUPPLY AIR AND RETURN (AIR BALANCE) IS DETERMINED BY THE PRESSURE CONTROLLER. FAST ACTUATING DAMPERS MODULATE DAMPER POSITION TO VARY RETURN AIR AND MAINTAIN PRESSURE SETPOINTS OF +0.01" W.C. POSITIVE PRESSURE FOR QA LAB RELATIVE TO THE WAREHOUSE AND +0.02" W.C. POSITIVE PRESSURE FOR MICROLAB RELATIVE TO THE WAREHOUSE. UPON MANUAL ACTIVATION OF CHEMICAL FUME EXHAUST HOOD (W/ BYPASS), THE MOTORIZED DAMPER OPENS AND EXISTING EXHAUST FAN ACTIVATES TO OPERATE AT FUME HOOD'S MAXIMUM COSTANT FLOW. UPON MANUAL ACTIVATION OF AUTOCLAVE EXHAUST HOOD, THE MOTORIZED DAMPER OPENS AND THE EXHAUST FAN WITH ECM ACTIVATES AND OPERATES AT USER ADJUSTABLE AIRFLOW UP TO 500 CFM. AN ADJUSTABLE TIMER AUTOMATICALLY SHUTS DOWN THE FAN AND CLOSES THE MOTORIZED EXHAUST DAMPER. UPON ACTIVATION OF LAB EQUIPMENT EXHAUST, THE RETURN AIR DAMPER IS CAPABLE TO MODULATE DOWN TO LOW FLOW AND WILL CLOSE SHUT AS NECESSARY TO MAINTAIN SPACE PRESSURIZATION. WHEN OCCUPANCY OVERRIDE SWITCH IS ENERGIZED, THE TERMINAL BOX CONTROL SHALL CHANGE TO OCCUPIED MODE FOR 2HRS (ADJUSTABLE). THERMOSTAT SETBACK SETPOINT: 65 OF HEATING AND 780 COOLING. ZONE TERMINAL SUPPLY BOX: SUPPLY AIRFLOW TO THE SPACE IS MODULATED FROM ITS MINIMUM AIRFLOW TO MEET TEMPERATURE SETPOINT. MINIMUM AIR FLOW IS EQUIVALENT TO 5 AIR CHANGES AS FOLLOWS: MICROLAB = 215 CFM QA LAB = 520 CFM THE ZONE REHEAT MODULATES TO MAINTAIN TEMPERATURE SETPOINT. RTU SUPPLY WILL MODULATE TO MAINTAIN DUCT STATIC PRESSURE SETPOINT TWO-THIRDS FROM RTU DOWNSTREAM IN THE MAIN SUPPLY TRUNK. ZONE RETURN DAMPER: DAMPER MODULATES TO TRACK THE SUPPLY AIR TO ACHIEVE THE REQUIRED AIR BALANCE UNDER THE CONTROL OF THE PRESSURE CONTROLLER AND MAINTAIN ROOM PRESSURIZATION. PRESSURE SETPOINTS ARE +0.01" W.C. POSITIVE PRESSURE FOR QA LAB RELATIVE TO THE WAREHOUSE AND + 0.02" W.C. POSITIVE PRESSURE FOR MICROLAB RELATIVE TO THE WAREHOUSE. RTU EXHAUST FANS WILL MODULATE TO MAINTAIN DUCT STATIC PRESSURE SETPOINT TWO-THIRDS FROM RTU UPSTREAM IN THE MAIN RETURN TRUNK. RELATIVE HUMIDITY WILL BE MONITORED AND RTU WILL BE SIGNALED TO ENTER DEHUMIDIFICATION MODE WHEN EITHER PRESSURE CONTROLLER WITH RH SENSOR IN THE SPACE OR RH SENSOR IN THE RETURN DUCT REPORT ABOVE 55% RH. UPON ACTIVATION OF LAB EQUIPMENT EXHAUST, THE SYSTEM SWITCHES TO OCCUPIED MODE. INPUT/OUTPUT SUMMARY (LAB EQUIPMENT EXHAUST) EQUIPMENT MOUNTED PANELS [:fl0o BINARY INPUT BINARY OUTPUT O ANALOG INPUT Ao ANALOG OUTPUT POINT ID POINT DESCRIPTION 1 AUTOCLAVE EXHAUST FAN DAMPER OPEN/CLOSE X 2 AUTOCLAVE EXHAUST FAN DAMPER STATUS X 3 AUTOCLAVE EXHAUST FAN STATUS X 4 AUTOCLAVE EXHAUST FAN START/STOP X 5 AUTOCLAVE EXH FAN ECM MOTOR CTRL ADJ X 6 FUME HOOD EXH. FAN DAMPER OPEN/CLOSE X 7 FUME HOOD EXHAUST FAN DAMPER STATUS X 8 FUME HOOD EXHAUST FAN STATUS X 9 FUME HOOD EXHAUST FAN START/STOP X 10 ROOM TEMPERATURE X 11 USER TEMPERATURE ADJUSTMENT X Grand total: 11 0 n EHXUAST AIR EF E EX S [7] MEP / FP Engineer EPSTEIN 600 West Fulton Chicago, IL 60661 312.454.9100 FROM CHEMICAL EHXUAST AIR FUME HOOD Design Architect EPSTEIN 600 West Fulton Chicago, IL 60661 312.454.9100 GENERAL NOTES: CONTROL CONTRACTOR SHALL PROVIDE WIRING AND INSTALLATION FOR REMOTE MOUNTED CONTROL DEVICES. AUTOCLAVE EXHAUST FAN: AUTOCLAVE EHXUAST FAN IS EQUIPPED WITH VARIABLE SPEED ECM MOTOR, AND SHALL BE FACTORY PRE-PROGRAMMED FOR AIRFLOW UP TO 500 CFM AND SOFT START AND SOFT STOP CAPABILITY. UPON MANUAL ACTIVATION, THE INTERLOCKED LOW LEAKAGE EXHAUST DAMPER OPENS BEFORE ECM FAN MOTOR STARTS. FAN MOTOR GRADUALLY RAMPS UP (SOFT START) AT A CONSTANT RATE OF 80 RPM UP TO USER ADJUSTABLE SPEED SETTING. EXHAUST FAN OPERATES FOR THE DURATION OF TIME INTERVAL SET AT THE TIMER (ADJUSTABLE) AND RAMPS DOWN (SOFT STOP) AT A CONSTANT RATE OF 80 RPM BEFORE SHUTTING OFF. EXHAUST DAMPER CLOSES TIGHT SHUT. CHEMICAL FUME HOOD EXHAUST FAN: UPON MANUAL ACTIVATION, THE INTERLOCKED LOW LEAKAGE EXHAUST DAMPER OPENS BEFORE FAN MOTOR STARTS. FAN MOTOR CONTINUOUSLY OPERATES UNTIL MANUALLY SHUT DOWN. EXHAUST DAMPER CLOSES SHUT TIGHT. WALL MOUNTED GREENHECK VAR[ -GREEN REMOTE DIAL CONTROL WITH SEPARATE DIGITAL ADJUSTABLE TIMER. ALTERNATE: WALL MOUNTED COMPATIBLE 0-10V SIGNAL MOTOR SPEED CONTROL WITH INTEGRATED TIMER AND ODIGITAL DISPLAY AND WITH ENGINEER'S APPROVAL. FROM ADJ MOTOR 10 AUTOCLAVE SPEED EXHAUST HOOD TIMER (ADJ) 11 ES Nestle Waters North America Nestle Waters North America 4330 20th Street Zephyrtiills, Florida 33542-6703 972.462.3663 Festld Waters C. � A 1 F! .4� m 4 09.18.2013 ISSUE FOR PERMIT 3 09.11.2013 ISSUE FOR BIDS 2 09.03.2013 CD REVIEW PACKAGE 1 08.16.2013 DD REVIEW PACKAGE NO. DATE REVISIONS/ISSUANCES PSTEIN 5i Architecture Chicago Interiors New York Engineering Bucharest Construction Warsaw 600 W. Fulton Street Chicago, IL 60661-1259 T 312.454.9100 www.epsteinglobal.com PROJECT NUMBER: 12386 PROJECT MANAGER: JK ARCH/ENG: LK SCALE: 1/8" =1'-0" DRAWN BY: JK CHECKED BY: LK MECHANICAL CONTROLS M-103 2.44% A. Epstein and Sons inWrarional, Inc. All rights reserved.