|
POWER AND COMMUNICATION NOTES
<br />1.
<br />WHERE THE ARCHITECTURAL POWER AND COMMUNICATION
<br />DRAWINGS INDICATE ITEMS SPECIFIED IN THE PROJECT
<br />ENGINEERING DOCUMENTS, THIS INFORMATION IS
<br />INCLUDED FOR THE PURPOSES OF COORDINATION AND
<br />LOCATION, ONLY.
<br />2.
<br />EXPOSED ELECTRICAL, BUILDING CONTROL AND
<br />COMMUNICATION DEVICES, INCLUDING LIGHTING FIXTURES,
<br />RECEPTACLES, SWITCHES, THERMOSTATS, FIRE ALARM
<br />A/V DEVICES AND TELEPHONES, SHALL BE LOCATED AS
<br />INDICATED ON THE ARCHITECTURAL DRAWINGS.
<br />3.
<br />SEE THE PROJECT ENGINEERING DOCUMENTS FOR
<br />MATERIAL AND INSTALLATION SPECIFICATIONS FOR THESE
<br />ITEMS
<br />4.
<br />ALL OPERABLE DEVICES SHALL BE LOCATED AT
<br />ACCESSIBLE HEIGHTS, AS SHOWN ON THE
<br />ARCHITECTURAL STANDARDS ELEVATIONS.
<br />5.
<br />COORDINATE LOCATION OF ELECTRICAL OUTLETS WITH
<br />EQUIPMENT REQUIREMENTS AND MILLWORK ELEVATIONS.
<br />6.
<br />ARCHITECT TO APPROVE ALL T-STAT AND FIRE PROBE
<br />LOCATIONS PRIOR TO INSTALLATION.
<br />7.
<br />ALL POWER AND COMMUNICATIONS RECEPTACLES SHALL
<br />BE ORIENTED HORIZONTALLY.
<br />8.
<br />LAB CABINETRY IS SHOWN FOR REFERENCE ONLY -
<br />CABINETRY TO BE COORDINATED WITH OWNERS VENDOR.
<br />GC TO COORDINATE WITH OWNER ANY WORK TO BE
<br />DONE ON COORDINATION BETWEEN CABINET VENDOR
<br />INSTALLATION, ELECTRICAL WORK AND EQUIPMENT
<br />INSTALLATION.
<br />GENERAL EQUIPMENT NOTES
<br />1.
<br />COORDINATE EXACT LOCATION, TERMINATIONS, MOUNTING
<br />HEIGHTS AND ELECTRICAL CHARACTERISTICS FOR EACH
<br />SPECIFIC MODEL AND PIECE OF EQUIPMENT WITH
<br />OWNER'S REPRESENTATIVE AND EQUIPMENT SUPPLIER
<br />PRIOR TO INSTALLATION. PROVIDE ELECTRICAL SERVICE
<br />AS REQUIRED FOR EACH PIECE OF EQUIPMENT. ALL
<br />RECEPTACLES SHALL BE OF VOLTAGE RATING AND
<br />AMPACITY TO MATCH MANUFACTURER'S
<br />RECOMMENDATIONS. INCLUDE ALL COSTS IN BASE BID
<br />PROPOSAL
<br />2.
<br />REFER TO SHEET A-201 FOR EQUIPMENT SCHEDULE.
<br />KEY NOTES
<br />NEW CARD READER SYSTEM AT THIS
<br />OINSTALL
<br />LOCATION AND COORDINATE WITH NEW DOOR,
<br />FRAME AND HARDWARE. COORDINATE
<br />INSTALLATION OF CARD READER WITH EXISTING
<br />SECURITY SYSTEM.
<br />HEIGHT OF POWER, TELEPHONE AND
<br />OCOORDINATE
<br />DATA RECEPTACLE DEVICES WITH NEW LAB
<br />CABINETRY, COUNTERTOP AND BACKSPLASH. ALL
<br />POWER OUTLETS WITHIN 6' OF WATER MUST BE
<br />A GFI RECEPTACLE.
<br />COORDINATE HEIGHT OF POWER. TELEPHONE AND
<br />3
<br />DATA RECEPTACLE DEVICES WITH EXISTING LAB
<br />EQUIPMENT.
<br />4
<br />AT ISLAND CABINETRY, GC TO PROVIDE AND
<br />INSTALL A POWER POLE FROM THE CEILING TO
<br />TOP OF COUNTERTOP WITH ELECTRICAL OUTLETS
<br />CONTAINED WITHIN POLE JUST ABOVE COUNTER.
<br />OF EXISTING ALARM STROBES TIED TO
<br />OLOCATION
<br />THE WATER PROCESSING PLC. STROBES TO
<br />REMAIN IN CURRENT LOCATION.
<br />OPROVIDE
<br />J-BOX IN WALL FOR DISHWASHER
<br />HOOK-UP.
<br />EXISTING CARD READER SYSTEM AT THIS
<br />OREUSE
<br />LOCATION AND COORDINATE WITH NEW DOOR,
<br />FRAME AND HARDWARE.
<br />8
<br />REUSE EXISTING CARD READERS ON BOTH SIDES
<br />OF DOOR AND EMERGENCY DOOR RELEASE AT
<br />THIS LOCATION. COORDINATE WITH NEW DOOR,
<br />FRAME AND HARDWARE.
<br />POWER & COMMUNICATION SYMBOLS
<br />ELECTRICAL DUPLEX RECEPTACLE
<br />®
<br />ELECTRICAL QUAD RECEPTACLE
<br />JUNCTION BOX
<br />TELE/DATA PORT RECEPTACLE
<br />©
<br />POWER POLE
<br />QS
<br />ALARM STROBE DEVICE - CEILING MOUNTED
<br />CR
<br />CARD READER DEVICE
<br />LIGHT SWITCH
<br />044"
<br />HEIGHT DESIGNATION ABOVE FINISHED FLOOR
<br />AFF
<br />FOR MOUNTING DEVICE
<br />1*1
<br />0
<br />Col
<br />4 I SPO,WER & COMMUNICATIONS PLAN 2 SPACALE:,RTITION PLAN
<br />CALE:
<br />REFLECTED CEILING PLAN NOTES
<br />1. REFER TO MECHANICAL AND FIRE PROTECTION ENGINEERING
<br />DRAWINGS FOR SCOPE OF WORK.
<br />2. SUBMIT ALL FIXTURE SAMPLES AND PRODUCT
<br />INFORMATION TO ARCHITECT FOR APPROVAL PRIOR TO
<br />COMMENCEMENT OF WORK.
<br />3. LIGHT FIXTURES ARE SHOWN FOR REFERENCE ONLY.
<br />SEE ELECTRICAL DRAWINGS FOR LIGHTING FIXTURE
<br />SPECIFICATIONS AND FOR ADDITIONAL LIGHTING
<br />FIXTURES, INCLUDING EXIT SIGNS, EMERGENCY LIGHTING,
<br />DISPLAY LIGHTING AND CABINET DISPLAY LIGHTING.
<br />4. ALL BLOCKING TO BE FIRE RETARDANT TREATED, U.N.O.
<br />5. ALL LIGHT SWITCHES SHALL BE GANGED TOGETHER IN A
<br />SINGLE FACEPLATE. G.C. TO COORDINATE ALL WALL
<br />MOUNTED DEVICES ARE GANGED IN AN ORGANIZED MANNER.
<br />REFER TO MOUNTING DIAGRAM ON SHEET CA-001.
<br />6. REFER TO FINISH SCHEDULE A-201 FOR ADDITIONAL
<br />CEILING SCOPE OF WORK.
<br />7. ALL HVAC GRILLS, DIFFUSERS, SPRINKLER HEADS, STROBES
<br />AND OTHER CEILING MOUNTED DEVICES SHALL BE
<br />CENTER® IN ACOUSTICAL CEILING TILES, U.O.N.
<br />KEY NOTES
<br />OCENTER CEILING GRID IN ROOM AS SHOWN TO
<br />ACCOMMODATE LIGHTING LAYOUT INDICATED ON
<br />THE DRAWINGS.
<br />OLOCATION OF EXHAUST FOR CHEMICAL HOOD.
<br />REFER TO MECHANICAL ENGINEERING DRAWINGS
<br />FOR MORE INFORMATION.
<br />OLOCATION OF EXHAUST HOOD OVER AUTOCLAVE.
<br />REFER TO MECHANICAL ENGINEERING DRAWINGS
<br />FOR MORE INFORMATION.
<br />RCP SYMBOLS
<br />F1 2' X 2' RECESSED, T5 FLUORESCENT LIGHT
<br />FIXTURE
<br />o�
<br />3 I SREFLECTED CEILING PLAN 11 I SDEMOLITION PLAN
<br />MEP / FP Engineer
<br />EPSTEIN
<br />600 West Fulton
<br />Chicago, IL 60661
<br />312.454.9100
<br />GENERAL NOTES
<br />1. FIELD VERIFY ALL DIMENSIONS AND CONDITIONS. IN THE
<br />EVENT THAT DISCREPANCIES ARE NOTED BETWEEN THE
<br />SITE CONDITIONS AND THE PROJECT DOCUMENTS, THE
<br />OWNER'S REPRESENTATIVE SHALL BE NOTIFIED
<br />IMMEDIATELY.
<br />2. ALL NEW PARTITIONS TO BE TYPE "A' UNLESS NOTED
<br />OTHERWISE. ALL EXISTING CONCRETE BLOCK WALLS SHALL
<br />BE TYPE "B". SEE PARTITION TYPES ON SHEET A-801.
<br />3. DOOR INSTALLATIONS ARE DESIGNATED 000
<br />SEE SHEET A-201 FOR DOOR SCHEDULE FO.
<br />4. ALL WORK IS TO BE DONE IN ACCORDANCE WITH LOCAL
<br />BUILDING CODES AND ALL OTHER CODES WHICH MAY
<br />HAVE AUTHORITY OVER THIS PROJECT. PROVIDE ALL
<br />NECESSARY SAFEGUARDS, BARRIERS, TEMPORARY POWER,
<br />LIGHTING, FIRE PROTECTION, ETC., AS REQUIRED DURING
<br />DEMOLITION AND CONSTRUCTION.
<br />5. ALL WOOD MATERIALS, INCLUDING FRAMING, BLOCKING,
<br />AND PLYWOOD, SHALL BE FIRE RETARDANT TREATED,U.N.O.
<br />6. ALL FIRE RATED CONSTRUCTION AND SMOKE PARTITIONS
<br />SHALL BE FULLY SEALED TO THE STRUCTURE ABOVE. ALL
<br />PENETRATIONS IN FIRE RATED CONSTRUCTION AND SMOKE
<br />PARTITIONS SHALL BE FULLY FIRESTOPPED.
<br />7. PARTITION REINFORCING/BLOCKING SHALL BE PROVIDED AT
<br />ALL LOCATIONS WHERE WALL MOUNTED MILLWORK,
<br />FURNITURE, EQUIPMENT, GRAB BARS, CLOSET RODS AND
<br />ACCESSORIES ARE SHOWN ON THE PROJECT DRAWINGS.
<br />8. ALL PARTITIONS THAT EXTEND FROM EXISTING PARTITIONS
<br />SHALL MATCH AND ALIGN WITH THE EXISTING
<br />CONSTRUCTION.
<br />9. ALL EXISTING FLOOR SLABS TO RECEIVE NEW FLOOR
<br />FINISHES SHALL BE PATCHED, REPAIRED, LEVELED AND
<br />PREPARED AS REQUIRED TO RECEIVE NEW SPECIFIED
<br />FLOORING MATERIAL
<br />10. MAXIMUM TRANSITION HEIGHT FROM EXISTING THRESHOLDS
<br />TO NEW FLOORING NOT TO EXCEED 1/2" (TYP.).
<br />11. COORDINATE ALL REQUIRED GYP. BD. CONTROL JOINT
<br />LOCATIONS WITH ARCHITECT.
<br />12. GC TO VERIFY ALL EXISTING WALLS EXTEND FROM FLOOR
<br />TO DECK AND ALL PENETRATIONS ARE PROPERLY SEALED.
<br />ALL NEW PARTITIONS MUST ALSO GO TO DECK AND HAVE
<br />PROPERLY SEALED PENETRATIONS TO ENSURE POSITIVE
<br />PRESSURE AND HUMIDITY LEVELS ARE MAINTAINED
<br />BETWEEN LAB AND SURROUNDING SPACES.
<br />GENERAL PLAN DEMOLITION NOTES
<br />1. ALL ITEMS SHOWN DASHED TO BE DEMOLISHED. REFER TO
<br />ENGINEERING DRAWINGS FOR ADDITIONAL DEMOLITION
<br />INFORMATION ON OTHER BASE BUILDING SYSTEMS AND
<br />STRUCTURAL COMPONENTS.
<br />2. ALL WORK IS TO BE DONE IN ACCORDANCE WITH LOCAL
<br />BUILDING CODES AND ALL OTHER CODES WHICH MAY HAVE
<br />AUTHORITY OVER THIS PROJECT. PROVIDE ALL NECESSARY
<br />SAFEGUARDS, BARRIERS, TEMPORARY POWER, LIGHTING,
<br />FIRE PROTECTION, ETC., AS REQUIRED DURING DEMOLITION.
<br />3. CONTRACTORS SHALL FIELD SURVEY SITE OF PROPOSED
<br />WORK TO DETERMINE THE EXTENT AND NATURE OF
<br />DEMOLITION WORK.
<br />4. WHERE EXISTING PARTITIONS ARE TO REMAIN (ADJACENT
<br />TO DEMOLITION OR NEW WORK), CONTRACTOR IS TO
<br />REMOVE ALL FINISH MATERIALS, PATCH AS REQUIRED TO
<br />MAKE AS NEW, AS OUTLINED IN THE CONTRACT
<br />DOCUMENTS.
<br />5. REMOVE ALL CONSTRUCTION SHOWN ON THE DRAWINGS AS
<br />"DEMOLISHED" INCLUDING, BUT NOT LIMITED TO FLOORING,
<br />PARTITIONS, CEILINGS AND ELEMENTS OCCURRING ABOVE
<br />FINISHED CEILING, HANGERS, STRAPS, AND OTHER
<br />ACCESSORY OBJECTS CONNECTED WITH DEMOLITION.
<br />6. REMOVE BUILT-IN CABINET WORK ONLY FROM WALLS
<br />SHOWN TO BE DEMOLISHED, UNLESS NOTED OTHERWISE.
<br />7. WHERE PARTITIONS ARE BEING REMOVED, ALL ELECTRICAL
<br />OUTLETS & SWITCHES SHALL BE DISCONNECTED AT
<br />DISTRIBUTION PANELS & ALL WIRE REMOVED FROM
<br />CONDUIT.
<br />8. REMOVE ALL LOW VOLTAGE OR SIGNAL CABLES AND
<br />CONNECTORS NO LONGER REQUIRED FOR THE OPERATION
<br />OF THE OWNER'S TELEPHONE, DATA OR OTHER SYSTEMS.
<br />9. REMOVE ALL FINISHES AND WALL BASES. PREP WALLS
<br />AND FLOORS AS REQUIRED FOR NEW FINISHES.
<br />10. COORDINATE WITH OWNER THE CAREFUL RELOCATION OF
<br />VARIOUS LARGE PIECES OF EXISTING LAB EQUIPMENT. SEE
<br />EQUIPMENT SCHEDULE FOR LIST OF EXISTING EQUIPMENT
<br />TO BE REUSED.
<br />11. ALL EXISTING PARTITIONS TO REMAIN SHALL HAVE ALL
<br />CLIPS/BRACKETS/HANGERS/ETC. REMOVED FROM SURFACE.
<br />ALL REMAINING WALLS SHALL BE PROPERLY
<br />PATCHED/REPAIRED FOR RECEIPT OF NEW SPECIFIED
<br />FINISH.
<br />Design Architect
<br />Nestle Waters North America
<br />EPSTEIN
<br />Nestle Waters North America
<br />600 West Fulton
<br />4330 20th Street
<br />Chicago, IL 60661
<br />Zephyrhills, Florida 33542-6703
<br />312.454.9100
<br />972.462.3663
<br />KEY NOTES
<br />ONEW EXTERIOR WINDOWS TO BE INSTALLED PER
<br />LOCAL BUILDING CODE TO MATCH EXISTING
<br />ADJACENT WINDOWS. CONTRACTOR TO VERIFY
<br />EXISTING WINDOW TYPE AND SUBMIT NEW
<br />WINDOW SPECIFICATIONS TO OWNER AND
<br />ARCHITECT FOR REVIEW.
<br />OINSTALL NEW PAINTED WINDOW SILLS AND
<br />INTERIOR DRYWALL AS NEEDED AT EXTERIOR
<br />WALL.
<br />3 LAB CABINETRY AND COUNTERTOP TO BE
<br />SUPPLIED AND INSTALLED BY OWNERS VENDOR
<br />GC TO PROVIDE IN -WALL BLOCKING FOR ALL
<br />UPPER CABINETRY.
<br />OCONTRACTOR TO COORDINATE RE -LOCATION OF
<br />EXISTING LAB EQUIPMENT WITH OWNER.
<br />PROVIDE NEW DOOR, FRAME AND HARDWARE.
<br />OCOORDINATE WITH CARD READER INSTALLATION.
<br />REFER TO DOOR SCHEDULE FOR MORE
<br />INFORMATION.
<br />OLOCATION OF NEW EMERGENCY EYEWASH/SPRAY
<br />HOSE UNIT. REFER TO PLUMBING ENGINEERING
<br />DRAWINGS FOR MORE INFORMATION.
<br />OPROVIDE ROUGH -IN PLUMBING BELOW SINK FOR
<br />DISHWASHER HOOK-UP. REFER TO PLUMBING
<br />ENGINEERING DRAWINGS FOR MORE INFORMATION.
<br />OLOCATION OF REINSTALLED TIMECLOCK.
<br />COORDINATE LOCATION WITH OWNER AND
<br />ELECTRICAL OUTLET.
<br />NORTH
<br />(T
<br />GENERAL RCP DEMOLITION NOTES
<br />1. ALL CEILING ELEMENTS INCLUDING, BUT NOT LIMITED TO
<br />GRID, TILE, LIGHTING, MECH. GRILLS AND ELEMENTS
<br />OCCURING ABOVE FINISHED CEILING, SUCH AS HANGERS,
<br />STRAPS AND OTHER ACCESSORY OBJECTS CONNECTED
<br />WITH THE CEILING ARE TO BE DEMOLISHED. REFER TO
<br />ENGINEERING DRAWINGS FOR ADDITIONAL DEMOLITION
<br />INFORMATION.
<br />2. ALL WORK IS TO BE DONE IN ACCORDANCE WITH LOCAL
<br />BUILDING CODES AND ALL OTHER CODES WHICH MAY
<br />HAVE AUTHORITY OVER THIS PROJECT. PROVIDE ALL
<br />NECESSARY SAFEGUARDS, BARRIERS, TEMPORARY
<br />POWER, LIGHTING, FIRE PROTECTION, ETC., AS REQUIRED
<br />DURING DEMOLITION.
<br />3. CONTRACTORS SHALL FIELD SURVEY SITE OF PROPOSED
<br />WORK TO DETERMINE THE EXTENT AND NATURE OF
<br />DEMOLITION WORK.
<br />KEY NOTES
<br />1 REMOVE EXISTING EXTERIOR WINDOWS, SILLS AND
<br />INTERIOR DRYWALL AS REQUIRED. PREPARE
<br />OPENINGS FOR REPLACEMENT WINDOWS.
<br />OCOORDINATE WITH OWNER ANY EXISTING LAB
<br />EQUIPMENT TO BE RELOCATED TO TEMPORARY
<br />LAB LOCATION.
<br />OREMOVE EXISTING DOOR, FRAME AND HARDWARE.
<br />OREMOVE EXISTING LAB CABINETRY AND
<br />4 COUNTERTOPS, INCLUDING SINKS, AND CAP
<br />PLUMBING AT SOURCE.
<br />OREMOVE EXISTING DOOR, FRAME, HARDWARE AND
<br />CARD READER SYSTEM.
<br />OREMOVE EXISTING TIMECLOCK AND RETURN TO
<br />OWNER FOR REINSTALLATION.
<br />OLOCATION OF EXISTING ALARM STROBES TIED TO
<br />THE WATER PROCESSING PLC. STROBES TO
<br />REMAIN IN CURRENT LOCATION. PROTECT DURING
<br />DEMOLITION PHASE.
<br />8 DURING DEMOLITION, CONTRACTOR TO
<br />COORDINATE MOLD REMEDIATION SCOPE OF
<br />WORK WITH QUALIFIED ENVIRONMENTAL
<br />CONSULTANT.
<br />4
<br />3
<br />09.18.2013
<br />09.11.2013
<br />ISSUE FOR PERMIT
<br />ISSUE FOR BIDS
<br />2
<br />09.03.2013
<br />CD REVIEW PACKAGE
<br />1
<br />NO.
<br />08.16.2013
<br />DATE
<br />DD REVIEW PACKAGE
<br />REVISIONS/ISSUANCES
<br />PSTEIN
<br />Architecture
<br />Chicago
<br />Interiors
<br />New York
<br />Engineering
<br />Bucharest
<br />Construction
<br />Warsaw
<br />600 W. Fulton Street
<br />Chicago, IL 60661-1259
<br />T 312.454.9100
<br />www.epsteinglobal.com
<br />PROJECT NUMBER: 12386
<br />PROJECT MANAGER: JK
<br />ARCH/ENG: LK
<br />SCALE: 1/8" = 1'-0"
<br />DRAWN BY: JK
<br />CHECKED BY: LK
<br />DEMOLITION, PARTITION,
<br />REFLECTED CEILING AND
<br />POWER & COMM. PLANS
<br />A-1 01
<br />©)=X A. Epstein and Sons Intem tonal, Inc. AH rights reserved
<br />
|