|
SECTION 061000 - ROUGH CARPENTRY
<br />1.01 SECTION INCLUDES
<br />A. TELEPHONE AND ELECTRICAL PANEL BOARDS.
<br />B. WOOD NAILERS AND CURBS FOR ROOFING AND ITEMS INSTALLED ON
<br />ROOF.
<br />C. CONCEALED WOOD BLOCKING FOR SUPPORT OF EQUIPMENT, SOFFIT
<br />PANELS, AND SIGNAGE.
<br />D. MISCELLANEOUS WOOD NAILERS AND FURRING STRIPS.
<br />1.02 REFERENCES
<br />A. AFPA T10 - WOOD FRAME CONSTRUCTION MANUAL, AMERICAN
<br />FOREST AND PAPER ASSOCIATION, 2001.
<br />B. AWPA C2 - LUMBER, TIMBER, BRIDGE TIES AND MINE TIES -
<br />PRESERVATIVE TREATMENT BY PRESSURE PROCESSES, AMERICAN
<br />WOOD -PRESERVERS' ASSOCIATION, 2001.
<br />C. PS - AND INDUSTRIAL PLYWOOD NATIONAL
<br />1 CONSTRUCTION N ,
<br />INSTITUTE OF STANDARDS AND TECHNOLOGY (DEPARTMENT OF
<br />COMMERCE), 1995. D. PS 20 - AMERICAN SOFTWOOD LUMBER
<br />STANDARD, NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY
<br />(DEPARTMENT OF COMMERCE), 1999. E. WWPA G-5 - WESTERN
<br />LUMBER GRADING RULES, WESTERN WOOD PRODUCTS ASSOCIATION,
<br />1998.
<br />1.03 QUALITY ASSURANCE
<br />A. LUMBER: COMPLY WITH PS 20 AND APPROVED GRADING RULES AND
<br />INSPECTION AGENCIES.
<br />1.04 DELIVERY, STORAGE, AND HANDLING
<br />A. COVER WOOD PRODUCTS TO PROTECT AGAINST MOISTURE.
<br />SUPPORT STACKED PRODUCTS TO PREVENT DEFORMATION AND TO
<br />ALLOW AIR CIRCULATION.
<br />PART 2 -PRODUCTS
<br />2.01 DIMENSION LUMBER FOR CONCEALED APPLICATIONS - ALL SHALL BE FIRE
<br />RETARDANT TREATED
<br />A. GRADING AGENCY: WESTERN WOOD PRODUCTS ASSOCIATION
<br />(VW11PA).
<br />B. SIZES: NOMINAL SIZES AS INDICATED ON DRAWINGS, S4S.
<br />C. MOISTURE CONTENT: S-DRY OR MC19.
<br />D. MISCELLANEOUS BLOCKING, FURRING, AND NAILERS:
<br />1. LUMBER: S4S, NO.2 OR STANDARD GRADE.
<br />2.02 CONSTRUCTION PANELS -ALL SHALL BE FIRE RETARDANT TREATED
<br />A. MISCELLANEOUS PANELS:
<br />1. CONCEALED PLYWOOD: PS 1, C-C PLUGGED, EXTERIOR
<br />GRADE.
<br />2. EXPOSED PLYWOOD: PS 1, A-D, INTERIOR GRADE.
<br />3. ELECTRICAL COMPONENT MOUNTING: APA RATED SHEATHING,
<br />FIRE RETARDANT TREATED.
<br />2.03 ACCESSORIES
<br />A. FASTENERS AND ANCHORS:
<br />1. FASTENERS: ZINC ELECTROPLATED STEEL FOR HIGH
<br />HUMIDITY AND TREATED WOOD LOCATIONS, UNFINISHED
<br />STEEL ELSEWHERE.
<br />2. DRYWALL SCREWS: BUGLE HEAD, HARDENED STEEL, POWER
<br />DRIVEN TYPE, LENGTH THREE TIMES THICKNESS OF
<br />SHEATHING.
<br />3. ANCHORS: TOGGLE BOLT TYPE FOR ANCHORAGE TO HOLLOW
<br />MASONRY, EXPANSION SHIELD AND LAG BOLT AT SOLID
<br />MASONRY, BOLT ADN BALLISTIC ANCHORAGES TO STEEL.
<br />2.04 FACTORY WOOD TREATMENT
<br />A. TREATED LUMBER AND PLYWOOD: COMPLY WITH REQUIREMENTS OF
<br />AWPA U1-05 - USE CATEGORY SYSTEM FOR WOOD TREATMENTS
<br />DETERMINED BY USE CATEGORIES, EXPECTED SERVICE CONDITIONS,
<br />AND SPECIFIC APPLICATIONS.
<br />B. FIRE -RETARDANT -TREATED MATERIALS
<br />1. GENERAL: COMPLY WITH PERFORMANCE REQUIREMENTS IN
<br />AWPA C20 (LUMBER) AND AWPA C27 (PLYWOOD). FLAME
<br />SPREAD SHALL BE 25 OR LESS PER ASTM E84
<br />a. USE EXTERIOR TYPE FOR EXTERIOR LOCATIONS AND WHERE INDICATED.
<br />b. USE INTERIOR TYPE A, HIGH TEMPERATURE (HT) FOR ENCLOSED ROOF
<br />FRAMING, FRAMING IN ATTIC SPACES, AND WHERE INDICATED.
<br />C. USE INTERIOR TYPE A, UNLESS OTHERWISE INDICATED.
<br />2. IDENTIFY FIRE -RETARDANT -TREATED WOOD WITH
<br />APPROPRIATE CLASSIFICATION MARKING OF TESTING AND
<br />INSPECTING AGENCY; AND WITH INFORMATION ACCEPTABLE
<br />TO AUTHORITIES HAVING JURISDICTION.
<br />C. SURFACE MOUNTED AND WALL BLOCKING
<br />1. FIRE -RETARDANT -TREATED MATERIALS
<br />a. GENERAL: COMPLY WITH PERFORMANCE REQUIREMENTS IN AWPA C20
<br />(LUMBER) AND AWPA C27 (PLYWOOD). FLAME SPREAD SHALL BE 25 OR LESS PER
<br />ASTM E84.
<br />b. USE EXTERIOR TYPE FOR EXTERIOR LOCATIONS AND
<br />WHERE INDICATED.
<br />C. USE INTERIOR TYPE A, HIGH TEMPERATURE (HT) FOR ENCLOSED
<br />ROOF FRAMING, FRAMING IN ATTIC SPACES, AND WHERE
<br />INDICATED.
<br />d. USE INTERIOR TYPE A, UNLESS OTHERWISE INDICATED.
<br />D. IDENTIFY FIRE -RETARDANT -TREATED WOOD WITH APPROPRIATE
<br />CLASSIFICATION MARKING OF TESTING AND INSPECTING AGENCY;
<br />AND WITH INFORMATION ACCEPTABLE TO AUTHORITIES HAVING
<br />JURISDICTION.
<br />E. PLYWOOD BACKING PANELS
<br />1. TELEPHONE, ELECTRICAL, EQUIPMENT BACKING PANELS: DOC
<br />PS 1, EXPOSURE 1, C-D PLUGGED, FIRE -RETARDANT TREATED,
<br />IN THICKNESS INDICATED OR, IF NOT INDICATED, NOT LESS
<br />THAN 3/44NCH (19-MM) NOMINAL THICKNESS. 4'x8' BOARD.
<br />2. WATER DELIVERY SYSTEM, FIRE-RETARDENT TREATED IN
<br />THICKNESS INDICATED OR, IF NOT INDICATED, NOT LESS THAN
<br />5/8-INCH (1 3-MM) NOMINAL THICKNESS.
<br />F. PRESSURE TREATMENT OF LUMBER ABOVE GRADE: AWPA
<br />TREATMENT C2 USING WATERBORNE PRESERVATIVE TO 0.25 LB/CU FT
<br />(4.0 KG/CU M) RETENTION.
<br />1. KILN DRY AFTER TREATMENT TO MAXIMUM MOISTURE
<br />CONTENT OF 19 PERCENT.
<br />2. TREAT WOOD IN CONTACT WITH ROOFING, FLASHING, OR
<br />WATERPROOFING.
<br />3. TREAT WOOD IN CONTACT WITH MASONRY OR CONCRETE.
<br />4. TREAT WOOD LESS THAN 18 INCHES (450 MM) ABOVE GRADE.
<br />PART 3 - EXECUTION
<br />3.01 FURRING INSTALLATION
<br />A. SET FURRING, NAILERS AND BLOCKING MEMBERS LEVEL, PLUMB, AND
<br />TRUE TO LINE. DISCARD PIECES WITH DEFECTS THAT WOULD LOWER
<br />REQUIRED STRENGTH.
<br />B. MAKE PROVISIONS FOR TEMPORARY CONSTRUCTION LOADS, AND
<br />PROVIDE TEMPORARY BRACING SUFFICIENT TO MAINTAIN
<br />STRUCTURE IN TRUE ALIGNMENT AND SAFE CONDITION UNTIL
<br />COMPLETION OF ERECTION AND INSTALLATION OF PERMANENT
<br />BRACING.
<br />C. INSTALL MEMBERS FULL LENGTH WITHOUT SPLICES UNLESS
<br />OTHERWISE SPECIFICALLY DETAILED.
<br />D. COMPLY WITH MEMBER SIZES, SPACING, AND CONFIGURATIONS
<br />INDICATED, AND FASTENER SIZE AND SPACING INDICATED, BUT NOT
<br />LESS THAN REQUIRED BY AFPA WOOD FRAME CONSTRUCTION
<br />MANUAL. E. PROVIDE MISCELLANEOUS MEMBERS AS INDICATED OR
<br />AS REQUIRED TO SUPPORT FINISHES, FIXTURES, SPECIALTY ITEMS,
<br />AND TRIM.
<br />3.02 SITE APPLIED WOOD TREATMENT
<br />A. APPLY PRESERVATIVE TREATMENT COMPATIBLE WITH FACTORY
<br />APPLIED TREATMENT AT SITE -SAWN CUTS, COMPLYING WITH
<br />MANUFACTURER'S INSTRUCTIONS.
<br />B. ALLOW PRESERVATIVE TO DRY PRIOR TO ERECTING MEMBERS.
<br />END OF SECTION
<br />SECTION 062000 - FINISH CARPENTRY
<br />PART1 GENERAL
<br />1.01 SECTION INCLUDES
<br />A.
<br />INSTALLATION OF MILLWORK.
<br />B.
<br />INSTALLATION OF OWNER RETAIL SHELVING (COORDINATE WITH PET
<br />SUPPLIES PLUS)..
<br />C.
<br />FINISH CARPENTRY ITEMS.
<br />D.
<br />HARDWARE AND ATTACHMENT ACCESSORIES.
<br />1.02 REFERENCES
<br />A.
<br />AWI (QSI) - ARCHITECTURAL WOODWORK QUALITY STANDARDS
<br />ILLUSTRATED, ARCHITECTURAL WOODWORK INSTITUTE, 1997,
<br />SEVENTH EDITION, VERSION 1.0.
<br />B.
<br />BHMA A156.9 - AMERICAN NATIONAL STANDARD FOR CABINET
<br />HARDWARE, BUILDERS HARDWARE MANUFACTURERS ASSOCIATION,
<br />2003 (ANSI/BHMA Al56.9).
<br />C.
<br />NEMA LD 3 - HIGH-PRESSURE DECORATIVE LAMINATES, NATIONAL
<br />ELECTRICAL MANUFACTURERS ASSOCIATION, 2000.
<br />1.03 SUBMITTALS
<br />A.
<br />SEE SECTION 013000 - ADMINISTRATIVE REQUIREMENTS FOR
<br />SUBMITTAL PROCEDURES.
<br />B.
<br />SHOP DRAWINGS: INDICATE MATERIALS, COMPONENT PROFILES,
<br />FASTENING METHODS, JOINTING DETAILS, AND ACCESSORIES TO A
<br />MINIMUM SCALE OF 1-1/2 INCH TO 1 FT (1:8).
<br />C.
<br />SAMPLES: SUBMIT TWO SAMPLES OF WOOD TRIM 6 INCHES LONG.
<br />1.04 QUALITY ASSURANCE
<br />1.05 DELIVERY, STORAGE, AND PROTECTION
<br />A.
<br />PROTECT WORK FROM MOISTURE DAMAGE.
<br />1.06 PROJECT CONDITIONS
<br />A.
<br />SEQUENCE INSTALLATION TO ENSURE UTILITY CONNECTIONS ARE
<br />ACHIEVED IN AN ORDERLY AND EXPEDITIOUS MANNER.
<br />B.
<br />COORDINATE THE WORK WITH PLUMBING ROUGH -IN, ELECTRICAL
<br />ROUGH -IN, AND INSTALLATION OF ASSOCIATED AND ADJACENT
<br />COMPONENTS.
<br />PART 2 PRODUCTS
<br />2.01 PLASTIC LAMINATE MATERIALS
<br />A.
<br />PLASTIC LAMINATE: NEMA LD 3, HGS, VGS, HGP AS REQUIRED TO SUIT
<br />APPLICATION, COLOR AND TEXTURE AS INDICATED ON DRAWINGS.
<br />B.
<br />LOW PRESSURE LAMINATE: MELAMINE, COLOR AS SPECIFIED ON
<br />DRAWINGS, AND SURFACE TEXTURE AS SELECTED.
<br />C.
<br />LAMINATE BACKING SHEET: NEMA LD 3, BKL, UNDECORATED PLASTIC
<br />LAMINATE.
<br />D.
<br />ADHESIVE: OF TYPES BEST SUITED TO INSTALLATION.
<br />2.02 WOOD TRIM
<br />A.
<br />SOFTWOOD LUMBER: GRADED IN ACCORDANCE WITH AWI
<br />ARCHITECTURAL WOODWORK QUALITY STANDARDS ILLUSTRATED,
<br />CUSTOM, AVERAGE MOISTURE CONTENT OF 6 PERCENT, SPECIES
<br />AND GRADE AS FOLLOWSINDICATED ON DRAWINGS.
<br />B.
<br />HARDWOOD LUMBER: GRADED IN ACCORDANCE WITH AWI
<br />ARCHITECTURAL WOODWORK QUALITY STANDARDS ILLUSTRATED,
<br />CUSTOM, AVERAGE MOISTURE CONTENT OF 6 PERCENT, SPECIES
<br />AND GRADE AS FOLLOWS: CLEAR POPLAR.
<br />2.03 FASTENERS
<br />A.
<br />FASTENERS: OF SIZE AND TYPE TO SUIT APPLICATION.
<br />B.
<br />CONCEALED JOINT FASTENERS: THREADED STEEL.
<br />2.04 ACCESSORIES
<br />A.
<br />LUMBER FOR SHIMMING, BLOCKING: SOFTWOOD LUMBER OF CEDAR
<br />SPECIES.
<br />B.
<br />PRIMER: ALKYD PRIMER SEALER TYPE.
<br />C.
<br />WOOD FILLER: SOLVENT BASE, TINTED TO MATCH SURFACE FINISH
<br />COLOR.
<br />2.05 HARDWARE
<br />A.
<br />HARDWARE: COMPLY WITH BHMA A156.9 AND AS INDICATED ON
<br />DRAWINGS.
<br />2.06 FABRICATION
<br />A.
<br />SHOP ASSEMBLE WORK FOR DELIVERY TO SITE, PERMITTING
<br />PASSAGE THROUGH BUILDING OPENINGS.
<br />B.
<br />CAP EXPOSED PLASTIC LAMINATE FINISH EDGES WITH MATERIAL OF
<br />SAME FINISH AND PATTERN.
<br />C.
<br />WHEN NECESSARY TO CUT AND FIT ON SITE, PROVIDE MATERIALS
<br />WITH AMPLE ALLOWANCE FOR CUTTING. PROVIDE TRIM FOR
<br />SCRIBING AND SITE CUTTING.
<br />D.
<br />APPLY PLASTIC LAMINATE FINISH IN FULL UNINTERRUPTED SHEETS
<br />CONSISTENT WITH MANUFACTURED SIZES. FIT CORNERS AND JOINTS
<br />HAIRLINE, SECURE WITH CONCEALED FASTENERS. SLIGHTLY BEVEL
<br />ARISES. LOCATE COUNTER BUTT JOINTS MINIMUM 2 FEET (600 MM)
<br />FROM SINK CUT-OUTS.
<br />E.
<br />APPLY LAMINATE BACKING SHEET TO REVERSE FACE OF PLASTIC
<br />LAMINATE FINISHED SURFACES.
<br />F.
<br />SHOP ASSEMBLE CASEWORK FOR DELIVERY TO SITE IN UNITS EASILY
<br />HANDLED AND TO PERMIT PASSAGE THROUGH BUILDING OPENINGS.
<br />G.
<br />FIT SHELVES, DOORS, AND EXPOSED EDGES WITH MATCHING VENEER
<br />EDGING OR AS DETAILED ON DRAWINGS. USE ONE PIECE FOR FULL
<br />LENGTH ONLY.
<br />H.
<br />DOOR AND DRAWER FRONTS: 3/4 INCH (19 MM) THICK, FLUSH
<br />OVERLAY STYLE.
<br />I.
<br />WHEN NECESSARY TO CUT AND FIT ON SITE, PROVIDE MATERIALS
<br />WITH AMPLE ALLOWANCE FOR CUTTING. PROVIDE TRIM FOR
<br />SCRIBING AND SITE CUTTING.
<br />J.
<br />APPLY PLASTIC LAMINATE FINISH IN FULL UNINTERRUPTED SHEETS
<br />CONSISTENT WITH MANUFACTURED SIZES. FIT CORNERS AND JOINTS
<br />HAIRLINE, SECURE WITH CONCEALED FASTENERS. SLIGHTLY BEVEL
<br />ARISES. LOCATE COUNTER BUTT JOINTS MINIMUM 2 FEET (600 MM)
<br />FROM SINK CUT-OUTS.
<br />K.
<br />APPLY LAMINATE BACKING SHEET TO REVERSE SIDE OF PLASTIC
<br />LAMINATE FINISHED SURFACES.
<br />L.
<br />FABRICATE METAL COUNTERTOP SURFACES PRESSURE GLUED TO
<br />PARTICLE BOARD CORE BACKING WITHOUT VISIBLE JOINTS.
<br />M.
<br />MECHANICALLY FASTEN BACK SPLASH TO COUNTERTOPS WITH STEEL
<br />BRACKETS AT 16 INCHES (400 MM) ON CENTER.
<br />2.07 SHOP FINISHING
<br />A.
<br />SAND WORK SMOOTH AND SET EXPOSED NAILS AND SCREWS.
<br />B.
<br />APPLY WOOD FILLER IN EXPOSED NAIL AND SCREW INDENTATIONS.
<br />C.
<br />ON ITEMS TO RECEIVE TRANSPARENT FINISHES, USE WOOD FILLER
<br />WHICH MATCHES SURROUNDING SURFACES AND OF TYPES
<br />RECOMMENDED FOR APPLIED FINISHES.
<br />D.
<br />FINISH WORK IN ACCORDANCE WITH AWI ARCHITECTURAL
<br />WOODWORK QUALITY STANDARDS ILLUSTRATED, SECTION 1500,
<br />SYSTEM TR-2 (TRANSPARENT).
<br />E.
<br />BACK PRIME WOODWORK ITEMS TO BE FIELD FINISHED, PRIOR TO
<br />INSTALLATION.
<br />PART 3 EXECUTION
<br />3.01 EXAMINATION
<br />A.
<br />VERIFY ADEQUACY OF BACKING AND SUPPORT FRAMING.
<br />B.
<br />VERIFY MECHANICAL, ELECTRICAL, AND BUILDING ITEMS AFFECTING
<br />WORK OF THIS SECTION ARE PLACED AND READY TO RECEIVE THIS
<br />WORK.
<br />C.
<br />SEE SECTION 061000-ROUGH CARPENTRY FOR INSTALLATION OF
<br />RECESSED AND CONCEALED WOOD BLOCKING.
<br />3.02 INSTALLATION
<br />A.
<br />SET AND SECURE MATERIALS AND COMPONENTS IN PLACE, PLUMB
<br />AND LEVEL.
<br />B.
<br />CAREFULLY SCRIBE WORK ABUTTING OTHER COMPONENTS, WITH
<br />MAXIMUM GAPS OF 1/32 INCH (1 MM). DO NOT USE ADDITIONAL
<br />OVERLAY TRIM TO CONCEAL LARGER GAPS.
<br />C.
<br />INSTALL COMPONENTS, FIXTURES AND TRIM WITH FASTENERS AND
<br />ADHESIVES AS INDICATED ON FABRICATORS SHOP DRAWINGS.
<br />PROVIDE MECHANICAL FASTENERS FOR THE INSTALLATION OF ALL
<br />COMPONENTS, INCLUDING INSTALLATIONS USING ADHESIVES.
<br />D.
<br />INSTALL HARDWARE.
<br />3.03 PREPARATION FOR SITE FINISHING
<br />A.
<br />SET EXPOSED FASTENERS. APPLY WOOD FILLER IN EXPOSED
<br />FASTENER INDENTATIONS. SAND WORK SMOOTH.
<br />B.
<br />SITE FINISHING: REFER TO SECTION 099100.
<br />C.
<br />BEFORE INSTALLATION, PRIME PAINT SURFACES OF ITEMS OR
<br />ASSEMBLIES TO BE IN CONTACT WITH CEMENTITIOUS MATERIALS.
<br />3.04 ERECTION TOLERANCES
<br />A.
<br />MAXIMUM VARIATION FROM TRUE POSITION: 1/16 INCH (1.5 MM).
<br />B.
<br />MAXIMUM OFFSET FROM TRUE ALIGNMENT WITH ABUTTING
<br />MATERIALS: 1/32 INCH (0.7 MM).
<br />3.05 SCHEDULE
<br />A.
<br />INSTALLATION SCHEDULE IS INDICATED ON DRAWINGS.
<br />END OF SECTION
<br />SECTION 072100 - THERMAL INSULATION
<br />PART 1 GENERAL
<br />1.01 SECTION INCLUDES
<br />A. BOARD INSULATION AT EXTERIOR WALL BEHIND INTERIOR GYPSUM
<br />BOARD WALL FINISH.
<br />B. BATT INSULATION AND VAPOR RETARDER IN EXTERIOR WALL
<br />CONSTRUCTION AND INTERIOR WALLS.
<br />C. BATT INSULATION FOR FILLING CREVICES IN EXTERIOR WALL AND
<br />ROOF.
<br />D. SOUND INSULATION FOR DEMISING WALLS AT PUBLIC PET WASH OR
<br />GROOMING AREAS.
<br />1.02 REFERENCES
<br />A. ASTM C 578 - STANDARD SPECIFICATION FOR RIGID, CELLULAR
<br />POLYSTYRENE THERMAL INSULATION, 2001.
<br />B. ASTM C 665 - STANDARD SPECIFICATION FOR MINERAL -FIBER
<br />BLANKET THERMAL INSULATION FOR LIGHT FRAME CONSTRUCTION
<br />AND MANUFACTURED HOUSING, 2001.
<br />1.03 ENVIRONMENTAL REQUIREMENTS
<br />A. DO NOT INSTALL INSULATION ADHESIVES WHEN TEMPERATURE OR
<br />WEATHER CONDITIONS ARE DETRIMENTAL TO SUCCESSFUL
<br />INSTALLATION.
<br />PART 2 PRODUCTS
<br />2.01 BOARD INSULATION MATERIALS
<br />A. EXTRUDED POLYSTYRENE BOARD INSULATION: ASTM C 578, TYPE IV,
<br />EXTRUDED POLYSTYRENE BOARD WITH EITHER NATURAL SKIN OR
<br />CUT CELL SURFACES, WITH THE FOLLOWING CHARACTERISTICS:
<br />1. BOARD SIZE: 24 X 96 INCH (1220 X 2440 MM).
<br />2. BOARD THICKNESS: THICKNESS IN INCHES( MM) AS
<br />INDICATED ON DRAWINGS..
<br />3. BOARD EDGES: SQUARE.
<br />4. COMPRESSIVE RESISTANCE: 15 PSI (173 KPA).
<br />5. BOARD DENSITY: 1.3 LB/CU FT (21 KG/CU M).
<br />6. MANUFACTURERS:
<br />a. DOW CHEMICAL CO: WWW.DOW.COM, STYROFOAM Z-MATE.
<br />b. OWENS CORNING CORP: WWW.OWENSCORNING.COM.
<br />C. PACTIV BUILDING PRODUCTS: WWW.PACTIVBUILDINGPRODUCTS.COM.
<br />7. SUBSTITUTIONS: SEE SECTION 016000 - PRODUCT
<br />REQUIREMENTS.
<br />2.02 BATT INSULATION MATERIALS
<br />A. BATT INSULATION: ASTM C 665, PREFORMED GLASS FIBER BATT FOR
<br />THERMAL AND SOUND ATTENUATION APPLICATIONS, FRICTION FIT,
<br />CONFORMING TO THE FOLLOWING:
<br />1. THICKNESS: AS INDICATED.
<br />2. MANUFACTURERS:
<br />a. CERTAINTEED CORPORATION: WWW.CERTAINTEED.COM.
<br />b. JOHNS MANVILLE CORPORATION: WWW.JM.COM.
<br />C. OWENS CORNING CORP: WWW.OWENSCORNING.COM.
<br />3. SUBSTITUTIONS: SEE SECTION 016000 - PRODUCT
<br />REQUIREMENTS.
<br />2.03 SOUND ATTENUATION BATTS
<br />A. TYPE: UNFACED GLASS FIBER ACOUSTICAL INSULATION COMPLYING
<br />WITH ASTM C665, TYPE 1.
<br />B. SIZE:
<br />THICKNESS WIDTH LENGTH
<br />3-112' 89MM 16" 406MM 24" 609MM 96" 2438MM
<br />2-112" 64MM 16" 406MM 24" 609MM 96" 2438MM
<br />C. SIZE:SURFACE BURNING CHARACTERISTICS:
<br />1. MAXIMUM FLAME SPREAD. 10
<br />2. MAXIMUM SMOKE DEVELOPED: 10
<br />WHEN TESTED IN ACCORDANCE WITH ASTM E 84.
<br />D. COMBUSTION CHARACTERISTICS: PASSES ASTM E 136.
<br />E. FIRE RESISTANCE RATINGS: PASSES ASTM E 119 AS PART OF A
<br />COMPLETE FIRE TESTED WALL ASSEMBLY.
<br />F. SOUND TRANSMISSION CLASS: STC50
<br />G. DIMENSIONAL STABILITY: LINEAR SHRINKAGE LESS THAN 0.1 %
<br />H. MANUFACTURERS:
<br />a. DOW CHEMICAL CO: WWW.DOW.COM, STYROFOAM Z-MATE.
<br />b. OWENS CORNING CORP: WWW.OWENSCORNING.COM.
<br />C. PACTIV BUILDING PRODUCTS: WWW.PACTIVBUILDINGPRODUCTS.COM.
<br />PART 3 EXECUTION
<br />3.01 EXAMINATION
<br />A. VERIFY THAT SUBSTRATE, ADJACENT MATERIALS, AND INSULATION
<br />MATERIALS ARE DRY AND THAT SUBSTRATES ARE READY TO RECEIVE
<br />INSULATION.
<br />B. VERIFY SUBSTRATE SURFACES ARE FLAT, FREE OF IRREGULARITIES.
<br />3.02 BOARD INSTALLATION AT EXTERIOR WALLS
<br />A. APPLY ADHESIVE TO BACK OF BOARDS:
<br />B. INSTALL BOARDS VERTICALLY ON WALLS.
<br />END OF SECTION
<br />SECTION 077100 - ROOFING
<br />PART 1 GENERAL
<br />1.01 ROOF IS EXISTING. ALL WORK SHALL BE IN CONFORMANCE WITH THE
<br />LANDLORD ROOF SYSTEM MANUFACTURER'S SPECIFICATIONS REQUIRED
<br />TO MAINTAIN WARRANTY.
<br />1.02 ALL ROOF WORK TO BE PERFORMED BY LANDLORD ROOFING
<br />CONTRACTOR.
<br />PART 2 PRODUCTS
<br />2.01 PROVIDE ALL INSULATION, ROOF MEMBRANE, FLASHING, ADHEASIVES AND
<br />FASTENERS REQUIRED TO PROVIDE A COMPLETE INSTALLATION.
<br />2.2. PROVIDE BUILT-UP CRICKETS AND SADDLES TO PROVIDE POSITIVE
<br />DRAINAGE AROUND ROOF MOUNTED EQUIPMENT.
<br />PART 3 EXECUTION
<br />3.01 PROTECT EXISTING ROOF SYSTEM FROM DAMAGE DURING CONSTRUCTION.
<br />3.02 INSTALL WORK IN ACCORDANCE WITH MANUFACTURER'S WRITTEN
<br />INSTRUCTIONS AND DETAILS.
<br />3.03 INSTALL INSULATION IN FULL THICKNESS AT ALL ROOF OPENINGS.
<br />END OF SECTION
<br />SECTION 079200 - JOINT SEALANTS
<br />PART 1 GENERAL
<br />1.01 SECTION INCLUDES
<br />A. SEALANTS AND JOINT BACKING.
<br />B. PRECOMPRESSED FOAM SEALERS.
<br />1.02 REFERENCES
<br />A. ASTM C 920 - STANDARD SPECIFICATION FOR ELASTOMERIC JOINT
<br />SEALANTS, 2002.
<br />B. ASTM C 1193 - STANDARD GUIDE FOR USE OF JOINT SEALANTS, 2000.
<br />C. ASTM D 1056 - STANDARD SPECIFICATION FOR FLEXIBLE CELLULAR
<br />MATERIALS -SPONGE OR EXPANDED RUBBER, 2000.
<br />D. ASTM D 1667 - STANDARD SPECIFICATION FOR FLEXIBLE CELLULAR
<br />MATERIALS -VINYL CHLORIDE POLYMERS AND COPOLYMERS
<br />(CLOSED -CELL FOAM), 1997.
<br />E. ASTM D 2628 - STANDARD SPECIFICATION FOR PREFORMED
<br />POLYCHLOROPRENE ELASTOMERIC JOINT SEALS FOR CONCRETE
<br />PAVEMENTS, 1991 (REAPPROVED 1998).
<br />1.03 SUBMITTALS
<br />A. SEE SECTION 013000 -ADMINISTRATIVE REQUIREMENTS, FOR
<br />SUBMITTAL PROCEDURES.
<br />B. PRODUCT DATA: PROVIDE DATA INDICATING SEALANT CHEMICAL
<br />CHARACTERISTICS.
<br />C. MANUFACTURERS COLOR SELECTION CHART FOR COLOR
<br />VERIFICATION AT EXPOSED TO VIEW SEALANTS.
<br />1.04 QUALITY ASSURANCE
<br />A. MAINTAIN ONE COPY OF EACH REFERENCED DOCUMENT COVERING
<br />INSTALLATION REQUIREMENTS ON SITE.
<br />B. APPLICATOR QUALIFICATIONS: COMPANY SPECIALIZING IN
<br />PERFORMING THE WORK OF THIS SECTION WITH MINIMUM 3 YEARS
<br />EXPERIENCE.
<br />1.05 ENVIRONMENTAL REQUIREMENTS
<br />A. MAINTAIN TEMPERATURE AND HUMIDITY RECOMMENDED BY THE
<br />SEALANT MANUFACTURER DURING AND AFTER INSTALLATION.
<br />1.06 WARRANTY
<br />A. SEE SECTION 017700 - CLOSEOUT SUBMITTALS, FOR ADDITIONAL
<br />WARRANTY REQUIREMENTS.
<br />B. CORRECT DEFECTIVE WORK WITHIN A FIVE YEAR PERIOD AFTER DATE
<br />OF SUBSTANTIAL COMPLETION.
<br />C. WARRANTY: INCLUDE COVERAGE FOR INSTALLED SEALANTS AND
<br />ACCESSORIES WHICH FAIL TO ACHIEVE AIRTIGHT SEAL
<br />D. GENERAL WARANTY: SPECIAL WARRANTIES SPECIFIED IN THIS
<br />ARTICLE SAHLL NOT DEPRIEVE THE OWNER OF OTHER RIGHTS THE
<br />OWNER MAY HAVE UNDER OTHER PROVISIONS OF THE CONTRACT
<br />DOCUMENTS AND SHALL BE IN ADDITON TO AND RUM CONCURRENT
<br />WITH THE OTHER WARRANTIES MADE BY THE CONTRACTOR UNDER
<br />REQUIREMENTS OF THE CONTRACT DOCUMENTS.
<br />E. SPECIAL INSTALLERS WARRANTY: WRITTEN WARRANTY SIRNED BY
<br />THE INSTALLER AGEEING TO REPAIR OR REPLACE ELATOMERIC JOINT
<br />SEALANTS THAT DO NOT COMPLY WITHTHE PERFORMANCE AND
<br />OTHER REQUIREMENTS OF THIS SECTION WITHIN A WARRANTY
<br />PERIOD OF TWO YEARS FOR THE DATE OF SUBSTANTIAL
<br />COMPLETION.
<br />F. SPECIAL MANUFACTURERS WARRANTY: WRITTEN WARRANTY SIGNED
<br />BY THE MANUFACTURER AGEEING TO REPAIR OR REPLACE
<br />ELATOMERIC JOINT SEALANTS THAT DO NOT COMPLY WITHTHE
<br />PERFORMANCE AND OTHER REQUIREMENTS OF THIS SECTION WITHIN
<br />A WARRANTY PERIOD OF FIVE YEARS FOR THE DATE OF SUBSTANTIAL
<br />COMPLETION.
<br />G. SPECIAL WARRANTIES SPECIFIED IN THIS THIS SECTION EXCLUDE
<br />DETERIORATION OR FAILURE OF ELASTOMERIC SEALANT FROM THE
<br />FOLLOWING:
<br />1. MOVEMENT OF THE STRUCTURE FROM STRESSES ON THE
<br />SEALANT THAT EXCEED THE SEALANT MANUFACTURERS
<br />WRITTEN SPECIFICATIONS FOR SEALANT ELONGATION AND
<br />COMPRESSION CAUSED BY STRUCTURAL SETTLEMENT OR
<br />ERRORS ATTRIBUTABLE TO DESIGN AND CONSTRUCTION.
<br />2. DISINTEGRATION OF JOINT SUBSTRATES FROM NATURAL
<br />CAUSES EXCEEDING DESIGN SPECIFICATIONS.
<br />3. MECHANICAL DAMAGE CAUSED BY INDIVIDUALS, TOOLS, OR
<br />OTHER OUTSIDE AGENTS.
<br />4. CHANGES IN THE SEALANT APPEARANCE CAUSED BY THE
<br />ACCUMULATION OF DIRT OR OTHER ATMOSPHERIC
<br />CONTAMINANTS.
<br />PART2 PRODUCTS
<br />2.01 EXTERIOR SEALANTS
<br />A. PROVIDE ONE OR TWO COMPONENT ALIPHATIC URETHANE WHER
<br />WHITE OR CUSTOM COLOR IS REQUIRED AND FOR VINYL TO VINYL
<br />WITH PRIMER, MASONRY TO MASONRY INCLUDIING CONTROL JOINTS,
<br />ALUMINUM TO MASONRY WITH PRIMER ON ALUMINUM AND FOR EIFS
<br />APPLICATIONS.
<br />1. USE ONE PRODUCT FOR THE ENTIRE JOB.
<br />2. PRODUCTS: WHEN WHITE COLOR IS REQUIRED.
<br />a. WHEN WHITE COLOR IS REQUIRED. ULTRA BY SONNEBORN
<br />3. PROVIDE ONE OF THE FOLLOWING WHEN NON WHITE COLOR IS
<br />SELECTED.
<br />a. SONOLASTIC NP 2 BY SONNEBORN
<br />b. DYNATROL II BY PECORA
<br />c. CHE-CALK 500 BY BOSTIC
<br />d. DYMERIC 511 BY TREMCO
<br />B. PROVIDE ONE PART POLYETHER, MODIFIED SILICONE,
<br />SIL-TERMINATED NON -SAG ELASTOMERIC SEALANT FOR METAL TO
<br />METAL, METAL TO GLASS, GLASS TO GLASS, FERROUS METAL TO
<br />VINYL, VINYL TO VINYL.
<br />1. PRODUCTS:
<br />a. SONOLASTIC 150 BY SONNEBORN
<br />b. DOW CORNING 790 BY DOW CORNING
<br />C. SILPUR SEALANT BY GE SILICONES
<br />C. PROVIDE TWO PART POLYURETHANE SELF LEVLEING SEALANT FOR
<br />EXTERIOR AND INTERIOR EXPANSION AND CONTROL JOINTS IN
<br />HORIZONTAL WEARING SURFACES.
<br />1. PRODUCTS
<br />a. SONOLASTIC SL 2 BY SONNEBORN
<br />b. DYNATRED BY PECORA
<br />C. CHEM CALK 550 BY BOSTIK
<br />D. PROVIDE ONE COMPONENT HIGH PERFORMANCE POLYURETHANE
<br />SEALANT FOR INTERIOR SEALANT IN CONTACT WITH EXTERIOR
<br />ALUMINUM STOREFRONT, DOORS AND FRAMES.
<br />1. PRODUCTS
<br />a. SONOLASTIC NP1 BY SONNEBORN
<br />b. DYNATROL 1 BY PECORA
<br />C. CHEM-CALK 2639 BY BOSTIK
<br />PART 3 EXECUTION
<br />3.01 EXAMINATION
<br />A. VERIFY THAT SUBSTRATE SURFACES ARE READY TO RECEIVE WORK.
<br />B. VERIFY THAT JOINT BACKING AND RELEASE TAPES ARE COMPATIBLE
<br />WITH SEALANT.
<br />3.02 PREPARATION
<br />A.
<br />REMOVE LOOSE MATERIALS AND FOREIGN MATTER WHICH MIGHT
<br />IMPAIR ADHESION OF SEALANT.
<br />B.
<br />CLEAN AND PRIME JOINTS IN ACCORDANCE WITH MANUFACTURER'S
<br />INSTRUCTIONS.
<br />C.
<br />PERFORM PREPARATION IN ACCORDANCE WITH MANUFACTURER'S
<br />INSTRUCTIONS AND ASTM C 1193.
<br />D.
<br />PROTECT ELEMENTS SURROUNDING THE WORK OF THIS SECTION
<br />FROM DAMAGE OR DISFIGUREMENT.
<br />3.03 INSTALLATION
<br />A.
<br />PERFORM WORK IN ACCORDANCE WITH SEALANT MANUFACTURER'S
<br />REQUIREMENTS FOR PREPARATION OF SURFACES AND MATERIAL
<br />INSTALLATION INSTRUCTIONS.
<br />B.
<br />PERFORM INSTALLATION IN ACCORDANCE WITH ASTM C 1193.
<br />C.
<br />MEASURE JOINT DIMENSIONS AND SIZE JOINT BACKERS TO ACHIEVE
<br />WIDTH -TO -DEPTH RATIO, NECK DIMENSION, AND SURFACE BOND
<br />AREA AS RECOMMENDED BY MANUFACTURER.
<br />D.
<br />INSTALL BOND BREAKER WHERE JOINT BACKING IS NOT USED. E.
<br />INSTALL SEALANT FREE OF AIR POCKETS, FOREIGN EMBEDDED
<br />MATTER, RIDGES, AND SAGS.
<br />F.
<br />APPLY SEALANT WITHIN RECOMMENDED APPLICATION TEMPERATURE
<br />RANGES. CONSULT MANUFACTURER WHEN SEALANT CANNOT BE
<br />APPLIED WITHIN THESE TEMPERATURE RANGES.
<br />G.
<br />TOOL JOINTS CONCAVE.
<br />3.04 CLEANING
<br />A.
<br />CLEAN ADJACENT SOILED SURFACES.
<br />3.05 PROTECTION OF FINISHED WORK
<br />A.
<br />PROTECT SEALANTS UNTIL CURED.
<br />END OF SECTION
<br />/;
<br />Z
<br />O
<br />1-
<br />a
<br />U
<br />W
<br />W
<br />H
<br />Q
<br />W
<br />.. 'e.'zf1 f'f '
<br />-i VJ
<br />Z
<br />O
<br />UQ
<br />Lu V
<br />LL
<br />=U
<br />U/W
<br />Q U)
<br />ISSUED FOR:
<br />PERMIT
<br />03.14.19
<br />BID
<br />03.14.19
<br />CONSTRUCTION
<br />00.00.00
<br />REVIEW SET
<br />03.14.19
<br />PROJECT MANAGER DESIGNER
<br />SS SS
<br />JOB NO.
<br />18390
<br />AS1 03
<br />
|