5935 Gall Blvd - Laserfiche WebLink

Browse Search

II THREADED ROD TO STRUCTURE II ^�I CLEVIS HANGER L l y �C IIJ � I fir II II PIPE OR II CONDUIT 6 WIDE SADDLEI II _ _ r I II 1 - RIGID INSULATION INSERT PIPING HANGERS 1. PROVIDE CLEVIS SUPPORTS WITH BEAM CLAMP, CONCRETE ANCHORS (CONCRETE STRUCTURE), SCREWED BRACKET (WOOD STRUCTURE). PROVIDE HANGER OUTSIDE OF INSULATION WITH RIGID FOAM GLASS INSULATION SECTION AT HANGERS. PROVIDE 16 GAUGE PIPING SADDLE AT EACH HANGER. NO WELDING OR CUTTING OF STEEL STRUCTURAL MEMBERS SHALL BE PERMITTED. LAYOUT BASIS SHALL BE ANVIL 260. ROD SIZE PER CLEVIS HANGER DIMENSIONS FOR EACH PIPE SIZE: 3/8" FOR 2" PIPE OR LESS, 1/2" UP TO 3" PIPE AND 5/8" FOR 4" PIPE 2. HANGER INSTALLATION FOR HOT WATER PIPING SHALL NOT PREVENT MOVEMENT FOR PIPING EXPANSION. SPACING AS FOLLOWS: STEEL PIPE: 1/2 TO 1-1/4 - 7' ; 1-1/2 TO 2-1/2 - 9' ; 3 &4 - 12' ; 6 &8 - 17' ; 10 AND UP- 22' COPPER PIPE: 1/2 TO 1 - 5' ; 1-1/4 TO 2 - 7' ; 2-1/2 AND UP - 9' CAST IRON: 10' WITH SUPPORT AT EACH JOINT, TAKEOFF, AND FITTING. PVC DRAINAGE (140 DEG F SERVICE UP TO 6 - 80 DEG F ABOVE 6 ): UP TO 3 - 3' ; 4 TO 6 - 4,; ABOVE 6 - 8' PVC VENT (80 DEG F SERVICE): UP TO 1-1/2 - 5' ; 2 -3 - 6' ; ABOVE 3 7' CHROME PLATED ESCUTCHEON AT WALL 3/4"xi/2" TEE. " C.W. SUPPLY '? HEADER ABOVE --\ \\J71, k, CEILING --- ----- -----L--- TRAP PRIMER VALVE WITH INTEGRAL BACKFLOW PREVENTER AND VACUUM BREAKER PORT. PRECISION PLUMBING PRODUCTS Pi-500 OR P2-500 —� 1/2" COPPER TUBIING TRAP SUPPLIES. ROUTE BELOW FLOOR TO FLOOR DRAIN TRAPS. SEE PLANS FOR EXACT NUMBER OF LINES. PIPE HANGER DETAIL. PROVIDE DISTRIBUTION HEADER ACCESSORY FOR PRIMERS SHOWN SERVING MULTIPLE FIXTURES. i I i NOTE: MOUNT THE TRAP PRIMER VALVE ABOVE CEILING AND AT LEAST ONE FOOT ABOVE THE FLOOD LEVEL RIM OF THE HUB DRAIN FLOOR FOR EVERY 20 FEET OF PRIMER LINE. PROVIDE WITH ACCESS PANEL WHERE LOCATED ABOVE A HARD CEILING). PROVIDE PRIMER SERVICE FOR ALL FLOOR DRAINS AND HUB DRAINS. TRAP PRIMER DETAIL COMBINATION T&P RELIEF VALVE ROUTE T&P DI TO SPILL INTC SINK. a;WI T =LIEF VALVE 3/4" CW ELECTRIC UNION, P ?ANSION TANK SURE TO WALL )EEP SHEETMETAL MN PAN ROUTE 3/4" DRAIN PAN TO MOP SINK ELEC. WATER HEATER DETAIL a PILLOW BLOCK MODEL SHOWN. MODEL 1.5 MAY USED FOR SMALLER PIPING. SEE P3.1 FOR PI SIZES. WC-2 LV-1 DOMESTIC WATER FLOOR PLAN_ NYLON ROLLER WITH TEFLON BASE MOUNTING HOLES FOR PLUMBER'S TAPE AS REQUIRED BY CODE. NOTE: 1) PIPE SUPPORTS SHALL BE SPACED AS SPECIFIED IN THE PLUMBING SPECIFICATIONS. 2) DO NOT ATTACH SUPPORTS TO ROOF. PROVIDE PROTECTIVE MEMBRANE BETWEEN ROOF AND SUPPORT PER ROOFING MANUFACTURER'S RECOMMENDATIONS. PROVIDED AND INSTALLED BY THE PLUMBING CONTRACTOR. 3) PIPING SUPPORT NOT PERMITTED ON REFRIGERANT OR ANY OTHER INSULATED ROOF PIPING, ROOF PLUMBING PIPE SUPPORT DETAIL VALVES FOR NATURAL GAS SYSTEM 1. PLUG VALVES (3" IN SIZE AND LARGER): VALVES SHALL BE THE SEMI -STEEL TYPE WITH CAST IRON BODY, LUBRICATED CAST IRON PLUG, FLANGED ENDS AND WRENCH OPERATED FOR 175 POUND W.O.G. VALVES LAYOUT BASIS SHALL BE WALWORTH1797F 2. PLUG VALVES (2 1/2" IN SIZE AND SMALLER): VALVES SHALL HAVE BRONZE BODY AND PLUG, THREADED ENDS AND SQUARE HEAD FOR 175 POUND W.O.G. VALVE LAYOUT BASIS SHALL BE: WALWORTH NO. 1736 3. BALL VALVES (1/2", 3/4", AND 1" UP TO 1/2 PSI FOR APPLIANCE CONNECTION): VALVE SHALL BE LEVER HANDLE, 600 PSI CWP RATED - 1/2 PSI FOR INDOOR APPLIANCE CONNECTIONS PER ANSI Z21.15 & CGA 9.1A. LAYOUT BASIS SHALL BE NIBCO GB1A. 4. LUBRICATED PLUG VALVES SHALL BE LUBRICATED AT THE FACTORY AND SEALANT SHALL BE DESIGNED FOR NATURAL GAS. PROVIDE SIX (6) STICKS OR TUBES OF SEALANT UTILIZED AND TURN SUCH OVER TO THE OWNER. PROVIDE ONE (1) VALVE WRENCH FOR EACH SIZE AND TYPE OF VALVE HEAD AND TURN SUCH WRENCHES OVER TO THE OWNER. 5. PRESSURE REGULATING VALVE: VALVE SHALL HAVE INTERCHANGEABLE ALUMINUM ORIFICE, MOLDED DEEP CONVOLUTION DIAPHRAGM WITH O-RING SEAL, PLATED STEEL DIAPHRAGM PLATE, STAINLESS STEEL LEVER PIN, ONE PIECE MOLDED BUNA-N VALVE SEAT, DIE CAST ZINC VALVE STEM, DELRINFI VENT VALVE WITH BUNA-N SEAT, SPRING LOADED INTERNAL RELIEF VALVE ASSEMBLY, 1" AND 3/4" THREADED VENT WITH STAINLESS STEEL SCREEN, FIBERGLASS REINFORCED POLETHELYNE SEAL CAP WITH INTEGRAL RELIEF VALVE STOP, AND FIELD INTERCHANGEABLE ADJUSTMENT SPRING, CSA 6-18 APPROVED. PROVIDE THREE SPRINGS AT RATED OUTLET PRESSURE PLUS SPRING FOR NEXT HIGHES AND LOWEST PRESSURE RATING FOR BALANCING PURPOSES. PROVIDE ALL VENTING REQUIRED BY THE MANUFACTURER FOR ALL INDOOR MOUNTED REGULATORS. LAYOUT BASIS SHALL BE ACTARIS B42N. 6. CONTRACTOR SHALL PROVIDE REGULATORS AT ALL APPLIANCE CONNECTIONS REGARDLESS OF SUPPLY PRESSURE UNLESS THE REQUIRED EQUIPMENT DELIVERY PRESSURE CAN BE DELIVERED WITHOUT THE USE OF A REGULATOR. 7. CONTRACTOR TO COORDINATE INLET/OUTLET PRESSURES WITH DRAWINGS AND GAS EQUIPMENT MANUFACTURERS REQUIREMENTS. 8. INSTALL ALL REGULATORS CLEAR OF ANY EQUIPMENT ACCESS SUCH THAT VALVE SPRINGS AND ORIFICE CAN BE ACCESSED WITHOUT REMOVING VALVE. MAKE CONNECTION TO OR APPLIANCE FLEX HOSE QUICK CONNECTION FITTING OR UNIT GAS MANIFOLD INSIDE CABINET WITH GROUND JOINT UNION. PROVIDE GROMMET IN CABINET FOR WATER -TIGHT SEAL FOR C HVAC CONNECTIONS. PRESSURE REGULATOR WITH VENT LIMITER OR VENT TO OUTDOORS. PROVIDE AT EACH APPLIANCE WHEN SERVICE IS GREATER THAN 7" W.C. cq-� FULL SIZE FULL PORT GAS COCK OR BALL VALVE RIP/DIRT POCKET NOTE: CONTRACTOR SHALL VERIFY ALL GAS FIRED EQUIPMENT CONNECTION LOCATIONS IN THE FIELD PRIOR TO INSTALLING ANY GAS PIPE MAINS OR BRANCHES. INSTALL THE GAS TRAIN SUCH THAT ACCESS PANEL SWINGSHALL NOT BE IMPEDED. GAS PIPING EQUIPMENT CONNECTION DETAIL, NATURAL GAS FLOOR PLAN vas„ _ 11_0„ LAP SEALANT S/S CLAMPING RING PRE -MOLDED PIPE FLASHING BOOT. — ATTACH BOOT TO ROOF PER ROOF MFR ---N RECOMMENDATIONS. TO INDOOR GAS EQUIPMENT--, PRESSURE REGULATOR WITH INTERNAL VENT. in STEEL SLEEVE WELD TO STRUCTURE AND FILL WITH WATER PROOF MASTIC GAS PIPING RUN TIGHT TO BOTTOM OF STRUCTURE GROUND JOINT UNION GAS COCK WITH PLUGGED 1/8" NPT TEST GAUGE CONNECTION DRIP/DIRT POCKET GAS PIPING DETAIL- ROOF INSTALLATION GAS PIPING ON ROOF. SEE P200 FOR ROUTING. GAS PIPE ADJUSTMENT AT ROOF OBSTRUCTIONS TYPICAL GAS PIPE SUPPORT. SEE DETAIL 13/P400 (TYP) • U z H Zw� �A c) C �co N o � co CD �UwwC/)a-) Nz�Q� L11::)I rr=cam F—UJzUco oN� � pc\l _- cn h� w z w v Q 0 Ir 0 J CONTRACT DATE: 01.05.2016 BUILDING TYPE: N/A PLAN VERSION: DEC 2015 SITE NUMBER: N/A STORE NUMBER: N/A SHELL BUILDOUT 5935 GALL BLVD ZEPHYRHILLS, FL 33541 REMODEL PHASE 1 DOMETIC WATER AND NATURAL GAS FLOOR PLANS P1.0 PLOT DATE: