|
I I I ii I I 1 U 1 I
<br />4
<br />3
<br />2
<br />1
<br />UI
<br />Ill
<br /><I
<br />DIYISI N 9 FINISHES C � . O E �T
<br />E. MATERIALS:
<br />1. GENERAL REQUIREMENTS: PAINTS NOT SPECIFICALLY LISTED SHALL BE "FIRST
<br />QUALITY" COMMERCIAL PRODUCTS FROM ONE OF THE FOLLOWING:
<br />a. BENJAMIN MOORE PAINT COMPANY.
<br />b. ICI PAINTS NORTH AMERICA
<br />2. ACRYLIC WALL SIZE: ONE OF THE FOLLOWING:
<br />a. ICI DEVOE "WONDERPRIME" DR51701 VAPOR BARRIER PRIMER/SEALER.
<br />b. ICI DULUX "ULTRA -HIDE" 1060 VAPOR BARRIER PRIMER/SEALER.
<br />c. BENJAMIN MOORE PAINT COMPANY "MOORE'S WALL -GRIP 203."
<br />F. SURFACE PREPARATION:
<br />1. PREPARE SURFACES BY REMOVING ALL DIRT, DUST, GREASE, OIL, MOISTURE, AND
<br />OTHER CONTAMINANTS WHICH WILL IMPAIR THE PROPER ADHESION OF THE FINISH.
<br />2. FERROUS METAL SHOP PRIMED UNDER OTHER SECTIONS: CLEAN PREVIOUSLY PRIMED
<br />SURFACES WITH NON -PETROLEUM BASED SOLVENT TO REMOVE OIL AND GREASE.
<br />REMOVE LOOSE RUST, BLISTERED AND PEELING PAINT TO BARE METAL BY SCRAPING,
<br />SANDING, AND WIRE BRUSHING IN ACCORDANCE WITH SSPC-SP2 AND SSPC-SP3.
<br />IMMEDIATELY APPLY TOUCH UP PRIME DAMAGED OR ABRADED SURFACES. LIGHTLY
<br />SAND ALL SHOP PRIME PAINTED SURFACES TO RECEIVE PAINT FINISH.
<br />3. GALVANIZED FERROUS METAL: CLEAN WITH NON -PETROLEUM BASED IN ACCORDANCE
<br />WITH SSPC-SP1; ABRADE SURFACE WITH 3M "SCOTCHBRITE HEAVY DUTY" (BROWN)
<br />PAD, AS NECESSARY TO ACHIEVE SUFFICIENT PROFILE FOR PAINT ADHESION.
<br />4. UNPRIMED FERROUS METAL:
<br />a. SOLVENT CLEAN IN ACCORDANCE WITH SSPC SP-1.
<br />b. COMMERCIAL BLAST PER SSPC SP6.
<br />5. WOOD - OPAQUE PAINT FINISH:
<br />a. SPOT COAT KNOTS, PITCH STREAKS, AND SAPPY SECTIONS WITH SEALER.
<br />b. FILL ALL NAIL HOLES AND CRACKS. SAND FILLER SMOOTH AND LEVEL WITH WOOD
<br />SURFACE.
<br />6. WOOD - TRANSPARENT FINISH: FILL ALL EXPOSED FINISH NAIL HOLES AND CRACKS
<br />WITH MATCHING COLOR FILLER AFTER PRIME COAT IS APPLIED. SAND FILLER SMOOTH
<br />AND LEVEL WITH ADJACENT SURFACES.
<br />7. CONCRETE AND CONCRETE MASONRY UNITS: REMOVE ALL CONTAMINANTS BY
<br />WASHING AND WIRE BRUSHING. SANDBLAST IF NECESSARY.
<br />8. GYPSUM PLASTER AND WALL BOARD: REMOVE ALL LIGHT DUST AND DIRT.
<br />9. EXISTING FINISHED SURFACES TO BE REPAINTED:
<br />a. REMOVE LOOSE, BLISTERED, SCALED, OR CRAZED FINISHES TO BARE SUBSTRATE;
<br />FEATHER NEW WORK INTO EXISTING WORK. PREPARE SURFACES TO THE NEAREST
<br />BREAK LINE IF NECESSARY TO BLEND NEW FINISHES WITH OLD FINISHES.
<br />b. WASH AND RINSE SURFACES WITH TRISODIUM PHOSPHATE AND WATER OR OTHER
<br />SOLUTION REQUIRED TO REMOVE REMAINING FILM WAX OIL GREASE, SMOKE OR
<br />FOREIGN MATTER WHICH WILL IMPAIR BOND OR CAUSE BLEED THROUGH OF NEWLY
<br />APPLIED FINISHES.
<br />c. LIGHTLY SAND, OR APPLY A LIQUID DEGLOSSER ON EXISTING SEMI -GLOSS AND
<br />HIGH -GLOSS FINISHES BEFORE REFINISHING.
<br />G. SPECIAL APPLICATION REQUIREMENTS:
<br />1. UNLESS SPECIFIED OR INDICATED OTHERWISE, FOLLOW PAINT MANUFACTURER'S
<br />LABEL DIRECTIONS FOR GENERAL APPLICATION PROCEDURES AND COVERAGE RATES.
<br />2. DO NOT APPLY FINISHES ON SURFACES THAT ARE NOT SUFFICIENTLY DRY. MAKE SURE
<br />EACH COAT OF FINISH IS DRY AND HARD BEFORE A FOLLOWING COAT IS APPLIED
<br />UNLESS THE MANUFACTURER'S DIRECTIONS STATE OTHERWISE.
<br />3. TINT FILLER TO MATCH STAIN WHEN CLEAR FINISHES ARE SPECIFIED; WORK FILLER
<br />WELL INTO GRAIN AND, BEFORE IT HAS SET, WORKING PERPENDICULARLY TO THE
<br />GRAIN, WIPE THE EXCESS FROM THE SURFACE.
<br />4. OPAQUE FINISHES:
<br />a. APPLY NUMBER OF COATS SCHEDULED FOR EACH APPLICATION, EXCEPT THAT
<br />ADDITIONAL FINISH COATS SHALL BE APPLIED AS NECESSARY FOR COMPLETE HIDING OF
<br />SUBSTRATE COLORS.
<br />b. APPLY PRIMER COATS UN -TINTED. WHERE MORE THAN ONE COAT OF PAINT IS REQUIRED,
<br />TINT EACH SUCCEEDING COAT UP TO THE FINAL COAT SIMILAR IN TINT, BUT SLIGHTLY
<br />LIGHTER IN VALUE (SHADE).
<br />c. SAND LIGHTLY BETWEEN COATS IF NECESSARY TO ACHIEVE REQUIRED FINISH; SAND
<br />BETWEEN ALL COATS APPLIED TO WOOD SUBSTRATES.
<br />5. ROLLERS FOR APPLICATION AND BACKROLLING OF LATEX PAINTS SHALL HAVE A NAP
<br />OF 3/8 INCH OR LESS.
<br />6. WHERE ROLLER TEXTURE IS SCHEDULED FOR APPLICATION TO GYPSUM BOARD
<br />SURFACES, FINISH COATS MAY BE ROLLER APPLIED, OR SPRAY APPLIED AND
<br />BACKROLLED AT CONTRACTOR'S OPTION.
<br />7. FACTORY PRIMED SURFACES: APPLY SCHEDULED FINISH SYSTEM, LESS PRIMER COAT,
<br />EXCEPT AS NECESSARY TO FOR PATCHING DAMAGE TO FACTORY PRIME COATING.
<br />8. EXCEPT WHERE SCHEDULED OR INDICATED OTHERWISE, THE INTENT IS TO PAINT ALL
<br />NEW ROOMS AND AREAS.
<br />9. EXISTING AREAS WHICH HAVE NOT BEEN REMODELED OR DO NOT HAVE PATCHED
<br />SURFACES ARE NOT TO BE REPAINTED. WHERE EXISTING SURFACES HAVE BEEN
<br />REMODELED OR PATCHED THE ENTIRE ROOM IS TO BE REPAINTED, INCLUDING THE
<br />ASSOCIATED ACCESS PANELS, ELECTRICAL PANELS, HOLLOW METAL DOORS AND
<br />FRAMES (BOTH SIDES), AND SIMILAR ELEMENTS WITHIN THE ROOM.
<br />H. INTERIOR SYSTEMS:
<br />1. GYPSUM BOARD - LATEX SYSTEM:
<br />a. SYSTEM: THREE COATS - FIRST COAT LATEX PRIMER SEALER (UN -TINTED), SECOND AND
<br />THIRD COAT LATEX PAINT.
<br />b. SHEEN: ROLLER TEXTURE, SATIN SHEEN, EXCEPT PROVIDE FLAT SHEEN AT LIGHT COVES,
<br />CEILINGS, SKYLIGHT AREAS, CLERESTORY AREAS, INTERIOR FASCIAS, AND OTHER LIGHT
<br />SENSITIVE SURFACES. VERIFY LOCATIONS OF EACH SHEEN WITH ARCHITECT BEFORE
<br />PROCEEDING WITH WORK.
<br />c. APPLICATION:
<br />i. USE ON ALL EXPOSED GYPSUM BOARD SURFACES, INCLUDING THE EXPOSED PORTIONS
<br />OF WALL SURFACES BETWEEN ADJACENT WALL -MOUNTED FIXTURES.
<br />ii, PROVIDE PRIME COAT ONLY BEHIND PERMANENTLY MOUNTED MECHANICALLY WALL
<br />MOUNTED FIXTURES.
<br />iii. DO NOT APPLY PRIMER OR PAINT COATINGS TO SURFACES TO RECEIVE ADHESIVELY
<br />MOUNTED MIRRORS OR TILE.
<br />2. GYPSUM BOARD - SURFACES TO RECEIVE WALL COVERING: APPLY ONE COAT OF
<br />ACRYLIC WALL SIZE.
<br />I. COLOR SCHEDULE: PROVIDE PAINT COLORS TO MATCH THOSE INDICATED ON THE
<br />DRAWINGS. WHERE A PAINT COLOR IS LISTED FROM A SPECIFIC MANUFACTURER, PAINT
<br />PRODUCTS FROM OTHER APPROVED MANUFACTURERS MAY BE USED, PROVIDED THE
<br />COLOR EXACTLY MATCHES THE SPECIFIED COLOR, AND THE PAINT SYSTEM MEETS THE
<br />SPECIFIED REQUIREMENTS. WHERE NO PAINT COLOR IS INDICATED, PROVIDE COLOR AND
<br />SHEEN AS SELECTED BY THE ARCHITECT.
<br />1. INSTALL SEALANT BEHIND FLANGES AND AT PENETRATIONS THROUGH PANELING, AND
<br />BETWEEN TOP CAP OF PANEL AND SUBSTRATE.
<br />2. CLEANING: REMOVE EXCESS ADHESIVE FROM FACE OF LAMINATE USING SOLVENT
<br />RECOMMENDED BY MANUFACTURER.
<br />Df�'imb 1 q SP ci TtfES
<br />101402 REST ROOM SIGNAGE
<br />A. SUMMARY:
<br />1. CODE -REQUIRED INTERIOR SIGNAGE.
<br />2. INSTALLATION OF SIGNAGE.
<br />B. SYSTEM DESCRIPTION:
<br />1. ACCESSIBILITY SIGNAGE: PROVIDE ACRYLIC PLASTIC REVERSE SILK SCREENED SIGNS
<br />WITH INTERNATIONAL SYMBOL OF ACCESSIBILITY, RAISED LETTERS, AND BRAILLE, AT
<br />ACCESSIBLE TOILET FACILITIES; ONE FOR EACH SEX.
<br />C. QUALITY ASSURANCE:
<br />1. REGULATORY REQUIREMENTS: SIGNAGE SHALL CONFORM TO THE REQUIREMENTS OF
<br />THE JURISDICTIONAL CODE AUTHORITIES.
<br />D. MATERIALS:
<br />1. PLASTIC SHEET: 1/8 INCH THICK ACRYLIC SHEET; LOW GLOSS FINISH.
<br />2. DOUBLE STICK TAPE: 3M "SCOTCH BRAND #665" DOUBLE -STICK, DOUBLE -COATED TAPE,
<br />1/4" WIDE.
<br />SECTION 10810 -TOILET ACCESSORIES
<br />A. QUALITY ASSURANCE
<br />1. CONFORM TO APPLICABLE ACCESSIBILITY CODE FOR LOCATING ACCESSORIES.
<br />B. MATERIALS
<br />1. STAINLESS STEEL: SHEET - IN ACCORDANCE WITH ASTM A 167, TYPE 304.
<br />2. STAINLESS STEEL: TUBING - IN ACCORDANCE WITH ASTM A 269.
<br />3. GALVANIZED STEEL: IN ACCORDANCE WITH ASTM A 366.
<br />4. MIRROR GLASS: IN ACCORDANCE WITH ASTM C 1036, TYPE L, CLASS 1, QUALITY Q1.
<br />DIVISION 10SPECIALTIES, tONT.
<br />C. ACCESSORIES
<br />1. FASTENERS: STAINLESS STEEL WHERE EXPOSED, HOT DIP GALVANIZED WHERE
<br />CONCEALED; TYPE BEST SUITED TO SUBSTRATE CONDITIONS.
<br />2. FRAMED MIRROR: BOBRICK B-1652436
<br />3. WASTE RECEPTACLE: PROVIDED BY T-MOBILE, INSTALLED BY G.C..
<br />4. SEAT COVER DISPENSER: HEALTH GUARDS ITEM# 420660, MODEL #HG12-FURNISHED BY
<br />T-MOBILES VENDOR, INSTALLED BY G.C.
<br />5. GRAB BAR: BOBRICK B-6806
<br />6. AUTOMATIC HAND DRYER: EXCEL XL-BW WITH ADA RECSEED MOUNTING KIT 40502.
<br />FIXED NOZZLE, WHITE FINISH. FURNISHED BY T-MOBILE'S VENDOR, INSTALLED BY G.C.
<br />7. 7. TOILET PAPER DISPENSER: BOBRICK B-76857
<br />D. FABRICATION
<br />1. USE STAINLESS STEEL FOR EXPOSED SURFACES; GALVANIZED STEEL MAY BE USED IN
<br />CONCEALED LOCATIONS. FORM EXPOSED SURFACES FROM SINGLE SHEET OF STOCK,
<br />FREE FROM JOINTS, AND FLAT WITHOUT DISTORTION. WELD JOINTS OF FABRICATED
<br />COMPONENTS AND GRIND SMOOTH. FABRICATE GRAB BARS OF TUBING, FREE OF
<br />VISIBLE JOINTS, RETURN TO WALL WITH END ATTACHMENT FLANGES. KNURL GRIP
<br />SURFACES. FABRICATE SOAP DISPENSERS TO OPERATE WITH LESS THAN 5 POUND
<br />FORCE. PROVIDE HANGERS, ADAPTERS, ANCHOR PLATES AND ACCESSORIES
<br />REQUIRED FOR INSTALLATION. KEY LOCKS ALIKE; FURNISH SIX (6) KEYS.
<br />2. FRAMED MIRRORS: ONE COAT OF ORGANIC MIRROR BACKING COMPOUND TO THE BACK
<br />SURFACE OF THE GLASS.
<br />3. BACKING: GALVANIZED SHEET STEEL. ISOLATE GLASS FROM FRAME AND BACKING WITH
<br />RESILIENT, WATERPROOF PADDING
<br />4. FINISHES:
<br />a. STAINLESS STEEL: NO.4 SATIN.
<br />b. GALVANIZING: ASTM A 123 TO 1.25 OUNCES PER SQUARE FOOT.
<br />c. CHROME PLATING: ASTM B 456, TYPE SC 2, POLISHED FINISH
<br />5. SHOP ASSEMBLE UNITS AND PACKAGE COMPLETE WITH ANCHORS AND FITTINGS.
<br />E. INSTALLATION
<br />1. SET PLUMB AND LEVEL, SQUARE AND RIGIDLY ANCHORED. INSTALL IN ACCORDANCE
<br />WITH MANUFACTURER'S INSTRUCTIONS.
<br />104416 FIRE EXTINGUISHERS AND CABINETS
<br />A. SUBMITTALS: PRODUCT LITERATURE, INCLUDING EXTINGUISHER DIMENSIONS.
<br />B. EXTINGUISHERS: MULTI -PURPOSE DRY CHEMICAL TYPE: HEAVY DUTY DOT STEEL TANK; UL
<br />RATING 2A-10B;C, 5 LB CAPACITY, FM APPROVED; RED ENAMEL FINISH; PRESSURE GAGE;
<br />METAL VALVES AND SIPHON TUBES.
<br />C. FIRE EXTINGUISHER CABINETS:
<br />1. TYPE ONE OF THE EMER POTTER-R: FOLLOWING): INC.-DV-VB-RR OR
<br />O 0 INC #7023
<br />#7023-DV-VB-RR-FRC AT RATED CONSTRUCTION, LARSEN'S MANUFACTURING COMPANY
<br />#2409-R3 OR #FS-2409-R3 AT RATED CONSTRUCTION, J.L INDUSTRIES #1817V17 OR
<br />#1817V17 FIRE-FX AT RATED CONSTRUCTION.
<br />2. STYLE: SEMI -RECESSED (APPROXIMATELY 2-1/2" PROJECTION; ROLLED EDGE); STEEL
<br />FRAME AND DOOR WITH CONTEMPORARY 2 INCH WIDE DOUBLE STRENGTH GLASS
<br />INSERT.
<br />3. FINISH: MANUFACTURER'S STANDARD BAKED WHITE ENAMEL INTERIOR; FURNISH TO
<br />SECTION 099000 FOR FIELD PAINTING.
<br />4. LETTERING: BLACK LETTERING IN VERTICAL FORMAT.
<br />D. FIRE EXTINGUISHER BRACKETS: MANUFACTURER'S STANDARD J-TYPE. PROVIDE AT FIRE
<br />EXTINGUISHER LOCATIONS WHERE NO CABINET IS INDICATED.
<br />E. INSTALLATION:
<br />1. INSTALL BRACKETS 48 INCHES FROM FINISHED FLOOR TO TOP OF BRACKET.
<br />2. SECURE RIGIDLY IN PLACE IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS.
<br />3. INSTALL CABINETS PLUMB AND LEVEL IN WALL OPENINGS IN LOCATIONS AS INDICATED.
<br />UNLESS OTHERWISE INDICATED, INSTALL 30 INCHES FROM FINISHED FLOOR TO INSIDE
<br />BOTTOM OF CABINET.
<br />4. WHEN RECESSED CABINETS ARE INSTALLED IN FIRE RATED WALLS, MAINTAIN FIRE
<br />RESISTANCE RATING CONTINUOUSLY BEHIND THE CABINET.
<br />5. INSTALL IN LOCATIONS AS INDICATED ON THE DRAWINGS.
<br />105623 WIRE STORAGE SHELVING
<br />A. GENERAL: SHELVING SHALL CARRY THE APPROVAL OF THE NATIONAL SANITATION
<br />FOUNDATION (NSF)
<br />B. PRODUCT: APPROVED PRODUCTS BELOW (OR EQUAL):
<br />a. ALERA WIRE SHELVING 48" X 24" X 72"
<br />b. METRO SUPER ERECTA® (SES) 48" X 24" X 72"
<br />C. MATERIAL: SHELVES SHALL BE BRIGHT BASIC CARBON STEEL WIRE. POSTS SHALL BE COLD
<br />ROLLED CARBON STEEL TUBING, ELECTRIC WELDED. PLASTIC CLIPS MATERIAL SHALL BE
<br />ABS.
<br />D. FINISH: BRIGHT PLATED
<br />E. SHELVES: CONSTRUCTION SHALL BE OF OPEN WIRE DESIGN OFFERING GREATER LIGHT
<br />PENETRATION AND VISIBILITY, LIGHTER WEIGHT, AIR CIRCULATION AND MINIMAL DUST AND
<br />DIRT ACCUMULATION.
<br />F. FABRICATION: FACE RIBS SHALL RUN FRONT TO BACK EQUALLY SPACED ON 20.6MM
<br />CENTERS AND TO BE OF 3AMM WIRE. EACH SIDE (FOUR) OF SHELF SHALL CONSIST OF A
<br />CORRUGATED, REINFORCING TRUSS OF 4,5MM WIRE. AT THE FRONT AND BACK OF THE
<br />SHELF, THIS CORRUGATED REINFORCING SHALL BE WELDED TO 6.2MM RIB WIRE RUNNING
<br />PERPENDICULAR AND ABOVE THE FACE RIBS. A 6.2MM RIB WIRE SHALL BE WELDED TO THE
<br />BOTTOM OF THE TRUSS. AT THE ENDS OF THE SHELF, THE CORRUGATED REINFORCING
<br />TRUSS SHALL BE WELDED TO PARALLEL 6.2MM WIRE RIBS. DEPENDING UPON THE WIDTH
<br />AND LENGTH OF THE SHELF, IT SHALL HAVE THREE OR FIVE LONGITUDINAL RIBS (6.2 MM)
<br />WELDED TO THE FACE RIBS. IN ADDITION, CERTAIN LONGER LENGTHS SHALL HAVE ONE OR
<br />TWO CORRUGATED REINFORCING TRUSSES (6.2MM) WELDED TO THE UNDERSIDE. AT EACH
<br />CORNER OF THE SHELF THERE SHALL BE A TAPERED, CONICAL FITTING MADE OF 2.6MM
<br />COLD ROLLED STEEL TO THE PARALLEL RIB SUPPORTS. THE FITTING SHALL BE DESIGNED
<br />TO ACCOMMODATE THE VERTICAL SUPPORTS. THE CORRUGATED TRUSS SHALL BE IN THE
<br />SHAPE OF THE LETTER "W."
<br />G. POSTS: SHALL OF 1" O.D. ROUND STEEL TUBING, 1.5 MM THICK. THEY SHALL HAVE ROLLED
<br />GROOVES SPACED AT 1" O.C. ALONG THEIR LENGTH. THE TOPOF THE POST SHALL HAVE A
<br />FINISHED PLASTIC CAP. A DIE CAST THREADED INSERT WITH AN ADJUSTABLE LEVELING
<br />FOOT SHALL BE SHIPPED LOOSE FOR LATER INSERTION INTO THE POST BOTTOM.
<br />H. METHOD OF ASSEMBLY: SHALL BE OF THE FRUSTAL-CONICAL DESIGN INCORPORATING A
<br />TWO PART TAPERED PLASTIC CLIP. ENGAGEMENT AND LOCKING SHALL BE ACCOMPLISHED
<br />WITH A PROTRUDING BEAD ON THE INNER CIRCUMFERENCE OF THE PLASTIC CLIP WHICH
<br />WILL MATCH THE GROOVE IN THE POST. TWO PLASTIC CLIPS SHALL BE ATTACHED TO EACH
<br />CORNER POST FOR EACH SHELF. BOTH THE CLIPS AND THE CORNER FITTING OF THE
<br />SHELVES SHALL HAVE THE IDENTICAL TAPER TO CREATE A WEDGE EFFECT, THEREBY
<br />LOCKING THE SHELF SECURELY IN A RIGID POSITION. NO SCREWS OR OTHER FITTINGS
<br />SHALL BE REQUIRED TO EFFECT THIS ASSEMBLY. SHELVES SHALL BE VERTICALLY
<br />ADJUSTABLE IN 1" INCREMENTS.
<br />I. LOAD CAPACITY: 800 LBS. PER SHELF EVENLY DISTRIBUTED. MAXIMUM LOAD PER
<br />ASSEMBLED UNIT NOT TO EXCEED 2,000 LBS.
<br />J. CASTORS: SHALL BE ZINC PLATE ROUND STEM CASTER WITH POLYURETHANE TREAD AND
<br />WHEEL DIMENSIONS OF 5" X 1 %". WIRE SHELF CARTS ARE STANDARD WITH (2) SWIVEL
<br />AND (2) SWIVEL LOCKING CASTORS.
<br />K. SEISMIC ANCHORAGE: WHERE REQUIRED BY CODE AND/OR JURISDICTION HAVING
<br />GOVERNANCE, PROVIDE CROSS -BRACING AND ANCHOR PLATES FOR SUPER ERECTA®
<br />(SES) PER MANUFACTURER'S SPECIFICATIONS,
<br />E3NISIt3N 11-NOT USA
<br />DI' LS#C f.1,1 Fl f f I H: O
<br />0124813 -ENTRANCE FLOOR MATS AND FRAMES
<br />A. RELATED DOCUMENTS
<br />1. DRAWINGS AND GENERAL PROVISIONS OF THE CONTRACT, INCLUDING GENERAL AND
<br />SUPPLEMENTARY CONDITIONS AND DIVISION 01 SPECIFICATION SECTIONS, APPLY TO
<br />THIS SECTION.
<br />B. PRODUCTS
<br />1. REGULATORY REQUIREMENTS: COMPLY WITH APPLICABLE PROVISIONS IN [THE U.S.
<br />ARCHITECTURAL & TRANSPORTATION BARRIERS COMPLIANCE BOARD'S ADA-ABA
<br />ACCESSIBILITY GUIDELINES FOR BUILDINGS AND FACILITIES] AND [ICC A117.1]
<br />I-V `I ` N .F Nf HIN - C NT,
<br />t� 1S C� �! �f� � ��, a
<br />2. RESILIENT ENTRANCE MAT: RETAIN "MANUFACTURERS" PARAGRAPH AND LIST OF
<br />MANUFACTURERS BELOW TO REQUIRE PRODUCTS FROM MANUFACTURERS LISTED OR
<br />A COMPARABLE PRODUCT FROM OTHER MANUFACTURERS.
<br />3. MANUFACTURERS:
<br />a. LEGACY NOP BY MATS INC., PO BOX 839,37 SHUMAN AVENUE, STOUGHTON, MA, 02072;
<br />TELEPHONE 800-MATS-INC (800-628-7462) OR 781-344-1536; FAX 781-344-1537;
<br />WWW.MATSINC.COM.
<br />b. FOR VESTIBULES OR WHERE LOWER PROFILE IS REQUIRED: SUPREME NOP BY MATS INC.
<br />4. RECESSED FRAMES: AS SHOWN IN DRAWINGS.
<br />5. COLOR: MILL FINISH
<br />C. EXECUTION
<br />1. EXAMINE SUBSTRATES AND CONDITIONS WHERE FLOOR MATS WILL BE INSTALLED. DO
<br />NOT PROCEED WITH INSTALLATION UNTIL UNSATISFACTORY CONDITIONS ARE
<br />CORRECTED. SUB FLOOR SHALL BE CLEAN AND DRY, AND WITHIN ACCEPTABLE
<br />TOLERANCES.
<br />2. INSTALLATION
<br />a. INSTALL RECESSED MAT FRAMES TO COMPLY WITH MANUFACTURER'S WRITTEN
<br />INSTRUCTIONS. SET MAT TOPS AT HEIGHT RECOMMENDED BY MANUFACTURER FOR MOST
<br />EFFECTIVE CLEANING ACTION; COORDINATE TOPS OF MAT SURFACES WITH BOTTOMS OF
<br />DOORS THAT SWING ACROSS MATS TO PROVIDE CLEARANCE BETWEEN DOOR AND MAT.
<br />b. INSTALL NECESSARY SHIMS, SPACERS, AND ANCHORAGES FOR PROPER LOCATION, AND
<br />SECURE ATTACHMENT OF FRAMES.
<br />3. INSTALL GROUT AND FILL AROUND FRAMES AND, IF REQUIRED TO SET MAT TOPS AT
<br />PROPER ELEVATIONS, IN RECESSES UNDER MATS. FINISH GROUT AND FILL SMOOTH
<br />AND LEVEL.
<br />D. PROTECTION
<br />4. AFTER COMPLETING FRAME INSTALLATION AND CONCRETE WORK, PROVIDE
<br />TEMPORARY FILLER OF PLYWOOD OR FIBERBOARD IN RECESSES AND COVER FRAMES
<br />WITH PLYWOOD PROTECTIVE FLOORING. MAINTAIN PROTECTION UNTIL CONSTRUCTION
<br />TRAFFIC HAS ENDED AND PROJECT IS NEAR SUBSTANTIAL COMPLETION.
<br />DIVISION`13 -NOT USED
<br />DIYISICiN 14 *AN07 USED
<br />DIVISION 'IICI, fly f=ffE
<br />SECTION 15000 - MECHANICAL, PLUMBING & FIRE PROTECTION
<br />A. MECHANICAL
<br />1. INSTALLATION AND MATERIALS OF ALL SYSTEMS SHALL CONFORM TO THE
<br />REQUIREMENTS OF THE CITY, COUNTY, STATE, AND NATIONAL CODES.
<br />2. THE CONTRACTOR SHALL BE RESPONSIBLE FOR AND REQUIRED TO VISIT THE SITE,
<br />VERIFY DIMENSIONAL DATA AND REVIEW EXISTING CONDITIONS BEFORE PROCEEDING
<br />WITH THE WORK. ANY CONFLICTS WITH THE EXISTING CONDITIONS SHALL BE BROUGHT
<br />TO THE ATTENTION OF THE ARCHITECT.
<br />3. A COMPLETE AND OPERABLE SYSTEM SHALL BE PROVIDED. THIS IS DEFINED AS ONE
<br />WHICH HAS BEEN FURNISHED, MOUNTED, INSTALLED, AND PLACED IN OPERATION,
<br />BALANCED FOR AIR AND WATER, TESTED FOR CONFORMANCE TO THE CAPACITIES
<br />CORRESPONDING TO THE DESIGN CRITERIA.
<br />4. THE SYSTEM SHALL BE INSTALLED AND ADJUSTED IN ACCORDANCE TO THE
<br />MANUFACTURER'S RECOMMENDATIONS, TESTED FOR SEQUENCE OF CONTROL
<br />INCLUDING FAIL SAFE AND LIFE SAFETY CONSIDERATIONS AND AVAILABLE IN A CLEAN
<br />CONDITION.
<br />5. COORDINATE LOCATIONS OF ALL VISIBLE DEVICES WITH THE LIGHTING PLAN.
<br />B. DESIGN CRITERIA - HVAC SYSTEM
<br />1. MAINTAIN AN AVERAGE TEMPERATURE OF 68 TO 70 DEGREES DURING THE WINTER. 75
<br />TO 77 DEGREES DURING THE SUMMER.
<br />2. INTERIOR ZONES SHALL BE DESIGNED TO SERVE 1,800 SQUARE FEET EACH. EXTERIOR
<br />ZONES SHALL BE DESIGNED TO SERVE 700 SQUARE FEET EACH.
<br />3. EXHAUST ALL TOILET ROOMS TO THE OUTSIDE AT A RATE OF 2 CFM PER SQ. FT.
<br />C. DESIGN CRITERIA - PLUMBING SYSTEM
<br />1. PROVIDE COMPLETE PLUMBING SYSTEMS NECESSARY TO OPERATE THE DEVICES
<br />SHOWN IN THESE DOCUMENTS.
<br />D. DESIGN CRITERIA - FIRE PROTECTION SYSTEM
<br />1. PROVIDE THE NECESSARY FIRE SPRINKLER SYSTEMS AND FIRE ALARM SYSTEMS TO
<br />GIVE COMPLETE PROTECTION AS REQUIRED BY CODE.
<br />E. MEP / SPRINKLER NOTES
<br />1. ALL FIRE SPRINKLER WORK SHALL BE PERFORMED BY A BASE BUILDING APPROVED
<br />CONTRACTOR. SPRINKLER HEADS IN GYPSUM BOARD AND MALL FRONTS SHALL BE
<br />CONCEALED HEAD TYPE. SEMI -RECESSED OR CONCEALED TYPE MAY BE USED IN
<br />LAY -IN CEILINGS VISIBLE TO CUSTOMERS. SURFACE MOUNTED HEADS ARE
<br />ACCEPTABLE IN THE BACK AREA.
<br />2. FIRE SPRINKLER DESIGN SHALL BE PERFORMED BY A STATE LICENSED DESIGNER.
<br />3. PAINT ALL DIFFUSERS AND GRILLS TO MATCH ADJACENT SURFACES.
<br />4. BATTERY PACKS FOR EMERGENCY LIGHTS SHALL BE REMOTE OR RECESSED.
<br />5. IF CEILING ACCESS PANELS ARE REQUIRED, PAINT TO MATCH ADJACENT SURFACE.
<br />6. ALL TRACK LIGHTS MOUNTED ON P1 FINISH SHALL BE WHITE.
<br />7. VERIFY LOCATIONS OF DEMISING WALLS, CLEAR HEIGHTS, COLUMNS, MALL FRONTS
<br />AND ANY OTHER SIGNIFICANT COMPONENTS WITH THOSE INDICATED ON THE PLAN.
<br />NOTIFY THE ARCHITECT OF ANY DIFFERENCES.
<br />8. CEILING HEIGHTS INDICATED ON SHEET A-3 ARE INTENDED TO REPRESENT AN "IF
<br />POSSIBLE" SCENARIO. IF THE EXISTING STRUCTURE, MAJOR DUCTWORK OR OTHER
<br />OBSTRUCTIONS PROHIBIT THE REFERENCED HEIGHTS, PROVIDE AS MUCH HEIGHT AS
<br />POSSIBLE, MAINTAINING A 6" DIFFERENCE FROM THE GYPSUM BOARD SURROUND TO
<br />THE LAY -IN CEILING. NOTIFY THE ARCHITECT OF THE DIFFERENCES PRIOR TO
<br />INSTALLATION.
<br />Df VII+DN "I I=ARE
<br />DIVISION 16
<br />SECTION 16720 - FIRE ALARM SYSTEM
<br />A. GENERAL
<br />1. CONDITIONS OF THE CONTRACT
<br />A. THE GENERAL CONDITIONS AND SUPPLEMENTARY CONDITIONS SHALL APPLY TO AND FORM
<br />PART OF THIS DIVISION.
<br />2. SCOPE:
<br />A. THIS SECTION INCLUDES ALL LABOR, MATERIAL, EQUIPMENT AND RELATED SERVICES
<br />NECESSARY TO FURNISH, INSTALL AND CONNECT A COMPLETE FIRE ALARM SYSTEM.
<br />B. A FIRE ALARM SYSTEM SHALL BE PROVIDED WHERE REQUIRED BY LOCAL CODES AND/OR
<br />AS REQUIRED BY THE AHJ.
<br />C. PROVIDE COMPLETE SYSTEM DESIGN AND SUBMITTAL INCLUDING PRODUCT DATA AND
<br />SHOP DRAWINGS AND SUBMIT TO T-MOBILE FOR APPROVAL. UPON T-MOBILE APPROVAL,
<br />SUBMIT TO THE AHJ FOR APPROVAL AND PERMIT. COORDINATE ALL INSPECTIONS AND
<br />PERFORM SYSTEM TESTING PER THE AHJ REQUIREMENTS.
<br />B. PRODUCTS
<br />1. COMPLY WITH NFPA 72 AND THE NEC AS APPLICABLE TO CONSTRUCTION AND
<br />INSTALLATION OF FIRE ALARM AND DETECTION SYSTEM COMPONENTS AND
<br />ACCESSORIES. PROVIDE COMPONENTS AND SYSTEMS WHICH ARE UL LISTED AND
<br />LABELED FOR FIRE ALARM. PROVIDE FIRE ALARM AND DETECTION SYSTEMS AND
<br />ACCESSORIES WHICH ARE FM APPROVED. COMPLY WITH STATE AND LOCAL
<br />REQUIREMENTS AS APPLICABLE.
<br />1 IRE ALARfW C N DIVISION .6 F � "T
<br />2. ACCEPTABLE MANUFACTURERS: EDWARDS, NOTIFIER, SIEMENS, SIMPLEX. WHERE
<br />PART OF THE LANDLORD SYSTEM PROVIDE DEVICES MANUFACTURED BY AND
<br />COMPATIBLE WITH LANDLORD SYSTEM.
<br />3. WHERE PART OF THE LANDLORD SYSTEM PROVIDE DEVICES MANUFACTURED BY AND
<br />COMPATIBLE WITH LANDLORD SYSTEM. COMPLY WITH ALL REQUIREMENTS AS
<br />ESTABLISHED BY THE AHJ AND LANDLORD FOR TENANT SPACES.
<br />4. THE SYSTEM SHALL OPERATE AS A LOW VOLTAGE, INTELLIGENT, POINT IDENTIFICATION
<br />FIRE MANAGEMENT SYSTEM. THE FIRE DETECTION AND CONTROL SYSTEM SHALL
<br />MONITOR INTELLIGENT (ANALOG) AND ADDRESSABLE (DIGITAL) DEVICES, TRADITIONAL
<br />INITIATING DEVICES, POINT IDENTIFY THE ALARM LOCATION AND TRANSMIT A SIGNAL
<br />TO THE MONITORING AGENCY.
<br />5. AN ALARM SHALL BE DISPLAYED ON AN 80 CHARACTER ALPHANUMERIC DISPLAY AT
<br />THE MAIN PANEL. WHEN REQUIRED BY THE AHJ, PROVIDE REMOTE 80 CHARACTER
<br />KEYPAD ANNUNCIATOR AT APPROVED LOCATION.
<br />6. PROVIDE REQUIRED INTERFACE CONNECTION TO FIRE SPRINKLER SYSTEM TAMPER
<br />SWITCHES, FLOW SWITCHES AND HIGH/LOW AIR PRESSURE ALARM SWITCHES.
<br />INCLUDE CONNECTION TO TAMPER SWITCHES IN EXTERIOR VAULTS.
<br />7. PROVIDE CONNECTION FROM DUCT SMOKE DETECTORS TO FAN STARTER CONTROL
<br />CIRCUIT. FANS SHALL BE SHUT DOWN ON LOCAL DETECTION ONLY. PROVIDE
<br />INTERFACE RELAY TO CONTROL SYSTEM.
<br />8. PROVIDE F.A. POWER AND FIRE CLOSURE SIGNAL CONNECTION TO ALL FIRE SHUTTERS
<br />IN CORRIDORS. SHUTTERS SHALL BE POWERED FROM FIRE ALARM PANEL.
<br />9. PROVIDE MANUAL STATIONS WHERE REQUIRED. MANUAL STATIONS SHALL BE DIE-CAST
<br />ALUMINUM WITH WHITE LETTERING AND RED FINISH. EQUIP WITH PLASTIC GUARDS.
<br />10. PROVIDE SMOKE DETECTORS WHERE REQUIRED. SMOKE DETECTORS SHALL BE
<br />PHOTOELECTRIC TYPE WITH VISUAL INDICATION OF DETECTOR ACTUATION.
<br />DETECTORS SHALL BE ADDRESSABLE AND INTELLIGENT TYPE.
<br />11. DUCT SMOKE DETECTORS SHALL BE PHOTOELECTRIC TYPE AND SHALL OPERATE AT
<br />AIR VELOCITIES OF 300 FEET PER MINUTE TO 2000 FEET PER MINUTE. AN INTEGRAL
<br />FILTER SYSTEM SHALL BE INCLUDED TO REDUCE DUST AND RESIDUE ACCUMULATION.
<br />AN AIR FLOW MONITOR SHALL BE INCLUDED TO INDICATE THE PRESENCE AND
<br />DIRECTION OF AIR FLOW THROUGH THE DETECTOR. PROVIDE FOR ALL FAN SUPPLYING
<br />AIR TO BUILDING WITH CFM TOTALS OF 2000 CFM OR GREATER. PROVIDE AT SUPPLY
<br />AND/OR RETURN DUCT AS REQUIRED BY LOCAL CODE.
<br />12. HORN/STROBES SHALL BE SOLID STATE CONSTRUCTION AND SHALL PRO
<br />DUCE A
<br />BROADBAND HORN SOUND OUTPUT OF 96 DBA (103 PEAK DBA) AT 10 FEET IN AN
<br />ANECHOIC CHAMBER. THE STROBES SHALL PRODUCE 8000 PEAK CANDLEPOWER AT
<br />ONE FLASH PER SECOND.
<br />C. EXECUTION:
<br />1. INSTALLATION:
<br />a. PROVIDE THE SYSTEM IN ACCORDANCE WITH THE PLANS AND SPECIFICATIONS, ALL
<br />APPLICABLE CODES AND THE MANUFACTURER'S RECOMMENDATIONS. ALL WIRING SHALL
<br />BE INSTALLED IN STRICT COMPLIANCE WITH ALL THE PROVISIONS OF NEC: ARTICLE 760 A
<br />AND C, POWER -LIMITED FIRE PROTECTIVE SIGNALING CIRCUITS OR, IF REQUIRED, MAY BE
<br />RECLASSIFIED AS NON -POWER LIMITED AND WIRED IN ACCORDANCE WITH NEC: ARTICLE
<br />760 A AND B. UPON COMPLETION, THE CONTRACTOR SHALL SO CERTIFY IN WRITING TO
<br />T-MOBILE AND GENERAL CONTRACTOR.
<br />b. THE SUPPLIER SHALL HAVE THE CAPABILITIES OF RESPONDING TO A SERVICE CALL WITH
<br />A FACTORY TRAINED TECHNICAL REPRESENTATIVE WITHIN 24 HOURS. ALSO, THIS
<br />SUPPLIER SHALL MAINTAIN AN ADEQUATE STOCK OF ALL PARTS NECESSARY FOR THE
<br />REPAIR OF THIS EQUIPMENT ON HAND AT ALL TIMES.
<br />c. THE SYSTEM, UPON COMPLETION OF INSTALLATION BY THE CONTRACTOR, SHALL BE
<br />CHECKED OUT AND ALL CONNECTIONS TO INITIATING AND INDICATING DEVICES SHALL BE
<br />SUPERVISED BY FACTORY TRAINED TECHNICIANS IN THE EMPLOY OF A FACTORY
<br />FRANCHISED DEALER FOR THE PRODUCT INSTALLED. EACH INDIVIDUAL DEVICE SHALL BE
<br />CHECKED OUT AND TESTED FOR OPERATION BY A FACTORY TRAINED TECHNICIAN.
<br />d. THE COMPLETED FIRE ALARM SYSTEM SHALL BE FULLY TESTED IN ACCORDANCE WITH
<br />NFPA 72H BY THE CONTRACTOR IN THE PRESENCE OF T-MOBILE'S REPRESENTATIVE AND
<br />THE LOCAL FIRE MARSHAL. UPON COMPLETION OF A SUCCESSFUL TEST, THE
<br />CONTRACTOR SHALL SO CERTIFY IN WRITING TO T-MOBILE.
<br />Mobi'le'D
<br />12920 SE 38th STREET
<br />BELLEVUE, WA 98006
<br />www.T-Mobile.com
<br />COPYRIGHT NOTICE
<br />THESE DRAWINGS AND SPECIFICATIONS ARE COPYRIGHTED AND SUBJECT TO
<br />COPYRIGHT PROTECTION AS AN'ARCHITECTURAL WORK" UNDER SEC. 102 OF
<br />THE COPYRIGHT ACT, 17 U.S.C. AS AMENDED JANUARY 2003. THE PROTECTION
<br />INCLUDES, WITHOUT LIMITATION, THE OVERALL FORM, ARRANGEMENT AND
<br />COMPOSITION OF SPACES AND ELEMENTS OF THE DESIGN. UNDER SUCH
<br />PROTECTION, UNAUTHORIZED USE OF THESE DRAWINGS AND SPECIFICATIONS
<br />MAY RESULT IN CESSATION OF CONSTRUCTION, BUILDING SEIZURE, AND/OR
<br />MONETARY LIABILITY.
<br />ARCHITECT
<br />rmUzioN
<br />9096 EAST BAHIA DRIVE
<br />SUITE 103
<br />SCOTTSDALE, AZ 85260
<br />DESIGN@FUZIONVE.COM
<br />WWW.FUZIONVE.COM
<br />VENDOR PROJECT NO: 21,11.212680
<br />O F F(0 '
<br />a! • ��PM LOUIS P1
<br />✓C
<br />ti,
<br />ReD AR
<br />02/10/2022
<br />CONSULTING ENGINEER
<br />N
<br />W
<br />Q
<br />Q r
<br />Z ! M
<br />W
<br />C� W J
<br />J = �
<br />V O J
<br />m J
<br />0
<br />W J =
<br />00
<br />� N W
<br />-tiN
<br />J
<br />J
<br />,Q
<br />V
<br />DATE: February 5, 2022
<br />SCALE: AS NOTED
<br />DRAWN BY: LEO V.
<br />SAP NUMBER:
<br />4SIR
<br />CORPORATE TENANT REBUILD
<br />LDC
<br />SHEET TITLE:
<br />SPECIFICATIONS
<br />4
<br />3
<br />M
<br />1
<br />SHEET NUMBER:
<br />
|