|
CONTRACTOR NOTES:
<br />1 . SABBATH EXCLUSION: NO WORK SHALL BE UNDERTAKEN DURING THE SABBATH (FRIDAY AT
<br />SUNSET THRU SATURDAY).
<br />2. OVERTIME: WORK PERFORMED DURING OVERTIME HOURS NOT INCLUDED IN THE CONTRACT
<br />FOR CONSTRUCTION SHALL BE APPROVED IN ADVANCE VIA CHANGE ORDER.
<br />3. ALL WORK SHALL BE DONE IN A SAFE WORKMANLIKE MANNER AND IN STRICT ACCORDANCE
<br />WITH THE LOCAL AND/ OR STATE (IF APPLICABLE) BUILDING CODES. NATIONAL ELECTRIC
<br />CODE (NEC), ADA-ADAAGS (ADOPTED HANDICAPP ACCESSIBILTY REQUIRMENTS), OSHA AND
<br />ALL APPLICABLE CODES, REGULATIONS, ORDINANCES AND AUTHORITITES HAVEING
<br />JURISDICTION.
<br />4. TO THE EXTENT REQUIRED BY LAW ALL WORK SHALL BE PERFORMED BY INDIVIDUALS DULY
<br />LICENSED AND AUTHORIZED BY LAW TO PERFORM SAID WORK.
<br />5. CONTRACTOR MAY AT ITS DISCRETION ENGAGE SUBCONTRACTORS TO PERFORM WORK
<br />HEREUNDER, PROVIDED CONTRACTOR SHALL FULLY PAY SAID SUBCONTRACTOR AND IN ALL
<br />INSTANCES REMAIN RESPONSIBLE FOR THE PROPER COMPLETION OF THIS CONTRACT.
<br />6. EACH SUBCONTRACTOR IS RESPONSIBLE FOR HAVING A THROUGH KNOWLEDGE OF ALL
<br />DRAWINGS AND SPECIFICATIONS IN THEIR RELATED FIELD. THE FAILURE TO ACQUAINT
<br />THEMSELVES WITH THIS KNOWLEDGE DOES NOT RELIEVE THEM OF ANY RESPONSIBLITY FOR
<br />PERFORMING THEIR WORK PROPERLY. NO ADDITIONAL COMPENSATION SHALL BE ALLOWED
<br />BECASUE OF CONDITIONS THAT OCCUR DUE TO FAILURE TO FAMILIARIZE WORKERS WITH THIS
<br />KNOWLEDGE.
<br />7. THE CONTRACTOR SHALL MAINTAIN THE INTEGRITY OF THE EXISTING BUILDING SECURITY AT ALL
<br />TIMES. THIS INCLUDES KEEPING THE BUILDING SECURE FROM PERSONS, ENVIRONMENTAL
<br />ELEMENTS OR HAZARDS. THE CONTRACTOR SHALL BE RESPONSIBLE TO MAINTAIN THE
<br />INTEGRITY OF ALL EXISTING SECURITY SYSTEMS.
<br />8. CONTRACTOR SHALL FURNISH OWNER APPROPRIATE RELEASES OR WAIVERS OF LIEN FOR ALL
<br />WORK PERFORMED OR MATERIALS PROVIDED AT THE TIME THE NEXT PERIODIC PAYMENT SHALL
<br />BE DUE.
<br />9. CONTRACTOR SHALL PROVIDE ALL CHANGE ORDERS IN WRITING. CHANGE ORDER SHALL
<br />DESCRIBE ALL COST, TIME AND INCLUDE A DESCRIPTION OF THE WORK. NO WORK SHALL
<br />COMMENCE WITHOUT CHANGE ORDER BEING SIGNED AND APPROVED BY BOTH OWNER
<br />AND ARCHITECT.
<br />10. CONTRACTOR WARRANTS IT IS ADEQUATELY INSURED FOR INJURY TO ITS EMPLOYEES AND
<br />OTHERS INCURRING LOSS OR INJURY AS A RESULT OF THE ACTS OF CONTRACTOR OR ITS
<br />EMPLOYEES AND SUBCONTRACTORS.
<br />11. CONTRACTOR SHALL AT ITS OWN EXPENSE OBTAIN ALL PERMITS NECESSARY FOR THE WORK TO
<br />BE PERFORMED.
<br />12. CONTRACTOR AGREES TO REMOVE ALL DEBRIS AND LEAVE THE PREMISES IN BROOM CLEAN
<br />CONDITION.
<br />13. IN THE EVENT OWNER SHALL FAIL TO PAY ANY PERIODIC OR INSTALLMENT PAYMENT DUE
<br />HEREUNDER, CONTRACTOR MAY CEASE WORK WITHOUT BREACH PENDING PAYMENT OR
<br />RESOLUTION OF ANY DISPUTE.
<br />14. CONTRACTOR SHALL NOT BE LIABLE FOR ANY DELAY DUE TO CIRCUMSTANCES BEYOND ITS
<br />CONTROL INCLUDING STRIKES, CASUALTY OR GENERAL UNAVAILABILITY OF MATERIALS.
<br />15. THE CONTRACTOR SHALL COMPLY WITH ALL APPLICABLE OSHA RULES AND REGULATIONS.
<br />16. ALL CONSTRUCTION CONDITIONS TO BE VERIFIED IN THE FIELD, ANY DISCREPANCIES,
<br />OMISSIONS AND ERRORS DISCOVERED BY THE CONTRACTOR SHALL BE BROUGHT TO THE
<br />ARCHITECT'S ATTENTION AT ONCE. THIS INCLUDES EXISTING AND NEW CONDITIONS AND
<br />DIMENSIONS. THE CONTRACTOR IS NOT TO PROCEED WITH OUT CONTACTING THE ARCHITECT,
<br />17. THE CONTRACT DOCUMENTS ARE A GRAPHIC REPRESENTATION OF THE CONDITIONS AND THE
<br />WORK TO BE DONE. THESE DOCUMENTS SHOULD NOT BE SCALED. THE WRITTEN DIMENSIONS
<br />SHALL TAKE PRECEDENT OVER ANY AND ALL SCALED DIMENSIONS. THE MANUFACTURERS
<br />SPECIFICATIONS SUPERSEDE THE CONTRACT DOCUMENTS AS APPLICABLE.
<br />18. ANY DEVIATION FROM THE CONTRACT DOCUMENTS MUST BE APPROVED BY THE ARCHITECT
<br />PRIOR TO CONSTRUCTION. ANY CHANGES THAT ARE NOT APPROVED SHALL BECOME THE
<br />RESPONSIBILITY OF THE CONTRACTOR
<br />19. ALL MATERIALS, SYSTEMS, AND COMPONENTS SHALL BE AS SPECIFIED AND INSTALLED IN
<br />ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS AND SPECIFICATIONS. THE
<br />CONTRACTOR COORDINATES THE WORK OF ALL TRADES, IN ORDER TO ASSURE PROPER
<br />COORDINATION.
<br />20. THE CONTRACTOR IS RESPONSIBLE FOR THE STORAGE AND SECURITY OF ALL BUILDING
<br />MATERIALS. THEY SHALL KEEP THE PREMISES AND WORK AREA IN A REASONABLY NEAT AND
<br />ORDERLY CONDITION. THE CLEANING OF THE AREAS ON A TIMELY BASIS IS NOT TO INTERFERE
<br />WITH ANY CONSTRUCTION CURRENTLY UNDER WAY.
<br />21. THE CONTRACTOR SHALL KEEP WORK AREA CLEAN AND FREE OF DEBRIS AND is TO REMOVE
<br />ALL TRASH AND DEBRIS FROM THE CONSTRUCTION AREA DAILY. NO FLAMMABLE MATERIALS
<br />OR LIQUIDS MAY BE STORED IN THE EXISTING BUILDING OR ANY NEW ADDITION.
<br />22. REMOVE ANY EXISTING ITEMS, SERVICES, FINISHES OR SURFACES AS REQUIRED FOR THE
<br />INSTALLATION OF NEW CONSTRUCTION. PROVIDE FURRING FOR CONDUITS AND PIPING,
<br />SHOWN OR NOT, AND FINISH OUT FURRING TO MATCH ADJACENT EXISTING FINISHES.
<br />COORDINATE INSTALLATION AND REMOVAL OF CONTRACTOR FURNISHED DUMPSTER WITH LANDLORD.
<br />23. REPAIR, RE-ROUTE, AND EXTEND ALL SERVICES, PIPING, CONDUIT OF EXISTING ITEMS AND
<br />EQUIPMENT AS REQUIRED DURING THE CONSTRUCTION PROCESS FOR THE COMPLETE
<br />INSTALLATION AND OPERATIONS OF NEW EQUIPMENT. THIS INCLUDES ALL ITEMS SHOWN OR
<br />NOT SHOWN ON THE DRAWINGS. RESET EXISTING EQUIPMENT OR RELATED ITEMS AS REQUIRED
<br />FOR PROPER OPERATION.
<br />24. THE CONTRACTOR SHALL BE RESPONSIBLE FOR THE TIMELY ORDERING OF MATERIALS TO
<br />PROHIBIT DELAYS OF THE CONSTRUCTION SCHEDULE OF THIS PROJECT. IT IS THE RESPONSIBILITY
<br />OF THE CONTRACTOR TO COORDINATE DELIVERY OF MATERIALS IN A TIMELY MANNER.
<br />25. THE GENERAL CONTRACTOR SHALL RESPOND TO ALL REQUIREMENTS OF THE
<br />ENGINEER/ARCHITECT FOR VERIFICATIONS, RESPONSES AND SUBMISSIONS.
<br />26. DURING ENTIRE CONSTRUCTION PERIOD, PROVIDE ONE U.L. LISTED 2A:20BC DRY CHEMICAL
<br />FIRE EXTINGUISHER, OR ONE STANDARD U.L. LISTED 2-1/2 GALLON WATER (E-1 0) AND ONE U.L.
<br />LISTED 1 OBC CARBON DIOXIDE FIRE EXTINGUISHER MOUNTED TOGETHER IN EACH 3000 SQ. FT.
<br />OF WORK AREA OR FRACTION THEREOF (MINIMUM OF TWO AVAILABLE IN ALL
<br />CONSTRUCTION AREAS AT ALL TIMES.)
<br />27. IF MODIFICATION TO SPRINKLER SYSTEM (WHEN SPRINKLED) IS REQUIRED, GENERAL
<br />CONTRACTOR SHALL HIRE A LICENSED SPRINKLER CONTRACTOR. SPRINKLER CONTRACTOR TO
<br />SUBMIT SIGNED AND SEALED SPRINKLER DRAWINGS TO THE ARCHITECT FOR APPROVAL PRIOR
<br />TO ANY ALTERATION OF THE AUTOMATIC SPRINKLER SYSTEM. WORK TO BE DONE UNDER
<br />SEPARATE PERMIT.
<br />28. CONTRACTOR IS RESPONSIBLE FOR PROTECTING ADJACENT PREMISES FROM MOISTURE,
<br />CONSTRUCTION NOISE, DUST AND DEBRIS.
<br />29. ANY DAMAGE CAUSED BY THE CONTRACTOR TO EXISTING FACILITY TO REMAIN SHALL BE
<br />REPAIRED TO BEFORE DAMAGE CONDITIONS AT THE CONTRACTOR'S SOLE EXPENSE.
<br />30. COORDINATE ALL WORK TO BE DONE WITH ALL THE CONTRACTORS INVOLVED PRIOR TO
<br />INSTALLATION.
<br />31. FIELD VERIFY LOCATIONS OF PIPING, EQUIPMENT, STRUCTURAL COMPONENTS, ETC. PRIOR TO
<br />COMMENCING ANY WORK.
<br />SECTION 00 72 00 - GENERAL CONDITIONS OF THE CONTRACT FOR CONSTRUCTION
<br />"General Conditions of the Contract for Construction', AIA A201 is hereby made a part of these documents as if bound herein. Copies of the AIA A201 can
<br />31. PROVIDE ADA COMPLIANT PRO WRAP DRAIN AND STOP INSULATION SYSTEM OR
<br />be obtained from Owners Representative.
<br />DRAINSHEILD ON ALL LAVATORIES.
<br />END OF SECTION 00 72 00
<br />32. ALL SPECIFIED ELECTRICAL NOTES ARE REQUIRED, ALL EQUIPMENT AND OUTLETS ARE TO
<br />SECTION 01 20 00 - PRICE AND PAYMENT PROCEDURES
<br />BE PLACED BY GENERAL CONTRACTOR.
<br />PART 1 - GENERAL
<br />33. FIRE EXTINGUISHERS, SMOKE AND FIRE DETECTION SYSTEMS TO BE INSTALLED BY GENERAL
<br />1.1 CONTRACT MODIFICATION PROCEDURES
<br />CONTRACTOR PER LOCAL CODE.
<br />A. On Owner's approval of a proposal from Contractor on AIA Document G709, Architect will issue a Change Order on AIA Document G701, for all changes to the
<br />Contract Sum or the Contract Time.
<br />34. ALL DIMENSIONS TO BE VERIFIED BY GENERAL CONTRACTOR ON SITE.
<br />B. When Owner and Contractor disagree on the terms of a proposal, Architect may issue a Construction Change Directive on AIA Document G714, instructing
<br />35. GENERAL CONTRACTOR SHALL MAKE FINAL CONNECTIONS TO ALL OWNER FURNISHED
<br />Contractor to proceed with the change, for subsequent inclusion in a Change Order. Construction Change Directive will contain a description of the change and
<br />ITEMS.
<br />designate the method to be followed to determine changes to the Contract Sum or the Contract Time.
<br />1.2 PAYMENT PROCEDURES
<br />36. GENERAL CONTRACTOR IS RESPONSIBLE TO COORDINATE DELIVERY, RECEIVE, UNLOAD,
<br />A. Submit a Schedule of Values at least 1 0 days before the initial Application for Payment. Break down the Contract Sum into at least one line item for each
<br />STORE, PROTECT ITEMS CALLED FOR IN SCOPE OF WORK FROM THE DELIVERY TRUCK
<br />INTO STORAGE AND THROUGH THE COMPLETE INSTALLATION PROCESS, ANY ITEMS
<br />Specification Section in the Project Manual table of contents. Coordinate the Schedule of Values with Contractors Construction Schedule.
<br />DAMAGED AFTER RECEIVING BY CONTRACTOR SHALL BE REPLACED AS DETERMINED BY
<br />1. Round amounts to nearest whole dollar; total shall equal the Contract Sum.
<br />THE OWNER, AT THE CONTRACTOR'S SOLE EXPENSE.
<br />2. Provide separate line items in the Schedule of Values for initial cost of materials and for total installed value of that part of the Work.
<br />B. Submit 3 copies of each application for payment on AIA Document G702/703, according to the schedule established in Owner/Contractor Agreement.
<br />37. ALL WOOD IN CONTACT WITH CONCRETE MUST BE PRESSURE TREATED MOISTURE
<br />RESISTANT.
<br />1. With each Application for Payment, submit waivers of mechanic's liens from subcontractors, sub -subcontractors, and suppliers for construction period covered
<br />by the previous application.
<br />38. REPAIR ROOF AT ALL ROOF PENETRATIONS AS REQUIRED TO MAINTAIN A WATERTIGHT /
<br />2. Submit final Application for Payment after completion of Project closeout procedures with release of liens and supporting documentation.
<br />PRE- PENETRATED ROOF SYSTEM.
<br />a. Include consent of surety to final payment on AIA Document G707 and insurance certificates.
<br />b. Submit final meter readings for utilities, a record of stored fuel, and similar data as of the date of Substantial Completion.
<br />39. RE -KEY ALL EXISTING LOCKSETS.
<br />PART 2 - PRODUCTS (Not Applicable)
<br />40. PROVIDE SIGN ON EXTEROR DOORS STATING "DOOR TO REMAIN UNLOCKED WHILE
<br />PART 3 - EXECUTION (Not Applicable)
<br />BUILDING IS OCCUPIED", I" HIGH LETTERS.
<br />END OF SECTION 01 20 00
<br />41. ALL DOOR HARDWARE TO MEET ADA GUIDELINES.
<br />SECTION 01 30 00 - ADMINISTRATIVE REQUIREMENTS
<br />PART 1 - GENERAL
<br />42. PROVIDE SIGN STATING MAXIMUM OCCUPANT LOAD WHERE REQUIRED BY AUTHORITY
<br />1. 1 PROJECT MANAGEMENT AND COORDINATION
<br />HAVING JURISDICTION.
<br />A. Coordinate construction to ensure efficient and orderly installation of each part of the Work.
<br />43. PROVIDE FIRESTOPPING MATERIAL AT ALL PENETRATIONS OF ANY FIRE WALL.
<br />B. Schedule and conduct progress meetings at Project site at regular intervals. Notify Owner and Architect of meeting dates and times. Require attendance of
<br />each subcontractor or other entity concerned with current progress or involved with planning or coordination of future activities-
<br />44. IF MODIFICATION TO FIRE ALARM SYSTEM (WHEN PRESENT) IS REQUIRED, GENERAL
<br />1. Architect will record minutes and distribute to everyone concerned, including Owner and Architect.
<br />CONTRACTOR SHALL HIRE A LICENSED FIRE ALARM CONTRACTOR. FIRE ALARM
<br />1.2 SUBMITTAL PROCEDURES
<br />CONTRACTOR TO SUBMIT SIGNED AND SEALED FIRE ALARM DRAWINGS TO THE
<br />ARCHITECT FOR APPROVAL PRIOR TO ANY ALTERATION OF THE FIRE ALARM SYSTEM.
<br />A. Coordinate each submittal with fabrication, purchasing, testing, delivery, other submittals, and related activities that require sequential activity.
<br />WORK TO BE DONE UNDER SEPARATE PERMIT.
<br />1. No extension of the Contract Time will be authorized because of failure to transmit submittals enough in advance of the Work to permit processing, including
<br />resubmittals.
<br />45. PROTECT EXISTING BUILDING STRUCTURAL SYSTEMS AND PROVIDE BRACING AT ALL
<br />2. Submit three copies of each submittal. Architect will return one copy.
<br />EXISTING PARTITIONS COMPROMISED BY DEMOLITION ACTIVITIES IN ANY WAY.
<br />3. Architect will discard submittals received from sources other than Contractor.
<br />46. CONSTRUCTION SAFEGUARDS REQUIRED EXITS, EXISTING STRUCTURAL ELEMENTS, FIRE
<br />B. Place a permanent label or title block on each submittal for identification. Provide a space approximately 6 by 8 inches on label or beside title block to record
<br />PROTECTION DEVICES AND SANITARY SAFEGUARDS SHALL BE MAINTAINED AT ALL TIMES
<br />Contractor's review and approval markings and action taken by Architect. Include the following information on the label:
<br />DURING REMODELING, ALTERATIONS, REPAIRS OR ADDITIONS TO ANY BUILDING OR
<br />1. Project name.
<br />STRUCTURE. EXCEPTIONS: 1. WHEN SUCH REQUIRED ELEMENTS OR DEVICES ARE BEING
<br />2. Date.
<br />REMODELED, ALTERED OR REPAIRED, ADEQUATE SUBSTITUTE PROVISIONS SHALL BE
<br />MADE. 2. WHEN THE EXISTING BUILDING IS NOT OCCUPIED. FBC 3302.1
<br />3. Name and address of Contractor.
<br />4. Name and address of subcontractor or supplier.
<br />5. Number and title of appropriate Specification Section.
<br />C. Identify deviations from the Contract Documents on submittals.
<br />ACCESSIBILITY N TES:
<br />D. Contractor's Construction Schedule Submittal Procedure: Submit two copies of schedule within 15 days after date established for Commencement ofthe Work.
<br />I . H.C. ACCESS TO THESE FACILITIES SHALL BE PROVIDED AT PRIMARY ENTRANCE
<br />PART 2 - PRODUCTS
<br />2.1 ACTION SUBMITTALS
<br />2. THE SLOPE OF PUBLIC WALKS SHALL NOT EXCEED MAX CROSS SLOPE 2% WALKING
<br />A. Product Data: Mark each copy to show applicable products and options. Include the following:
<br />SURFACE SLOPING GREATER THEN 2% SHALL BE SLIP RESISTANT
<br />1. Manufacturer's written recommendations, product specifications, and installation instructions.
<br />3. EVERY REQUIRED EXIT DOORWAY SHALL BE SIZED FOR A DOOR NOT LESS THEN 31-01 WIDE
<br />2. Wiring diagrams showing factory -installed wiring.
<br />BY NOT LESS THEN 6-8" HIGH CAPABLE OF OPENING 9T DEGREES AND MOUNTED TO
<br />3. Printed performance curves and operational range diagrams.
<br />THAT THE CLEAR WIDTH OF EXIT WAY IS 32'MIN.
<br />4. Testing by recognized testing agency.
<br />5. Compliance with specified standards and requirements.
<br />4. THRESHOLD TO BE MAX 1/4'ABOVE ADJACENT FINISH FLOOR
<br />B. Shop Drawings: Prepare Project -specific information, drawn accurately to scale. Do not base Shop Drawings on reproductions of the Contract Documents or
<br />5. MAXIMUM EFFORT TO OPERATE DOORS SHALL NOT EXCEED 5 LBS.
<br />standard printed data. Submit on sheets at least 8-1/2 by I I inches but no larger than 30 by 42 inches. Include the following:
<br />1. Dimensions and identification of products.
<br />6. THE BOTTOM I 9'OF ALL DOORS EXCEPT AUTOMATIC AND SLIDING SHALL HAVE A
<br />2. Fabrication and installation drawings and roughing -in and setting diagrams.
<br />SMOOTH UNINTERRUPTED SURFACE.
<br />3. Wiring diagrams showing field -installed wiring.
<br />7. PROVIDE LEVER TYPE HARDWARE, PANIC BARS, PUSH-PULL ACTIVATING BARS, OR
<br />4. Notation of coordination requirements.
<br />OTHER HARDWARE DESIGNED TO PROVIDE PASSAGE WITHOUT REQUIRING THE ABILITY
<br />5. Notation of dimensions established by field measurement.
<br />TO GRASP THE OPENING HARDWARE (39- TO 44- AFF.)
<br />C. Samples: Submit Samples for review of kind, color, pattern, and texture and for a comparison of these characteristics between submittal and actual component
<br />as delivered and installed. Include name of manufacturer and product name on label.
<br />1. If variation is inherent in material or product, submit at least three sets of paired units that show variations.
<br />2.2 INFORMATION SUBMITTALS
<br />A. Qualification Data: Include lists of completed projects with project names and addresses, names and addresses of architects and owners, and other information
<br />specified.
<br />B. Product Certificates: Prepare written statements on manufacturer's letterhead certifying that product complies with requirements in the Contract Documents.
<br />2.3 CONTRACTOR'S CONSTRUCTION SCHEDULE
<br />A. Gantt -Chart Schedule: Submit a comprehensive, fully developed, horizontal Ganft-chart-type schedule within 15 days of date established for commencement
<br />of the Work.
<br />B. Preparation: Indicate each significant construction activity separately. Identify first workday of each week with a continuous vertical line.
<br />PART 3 - EXECUTION
<br />3.1 SUBMITTAL REVIEW
<br />A. Review each submittal and check for coordination with other Work of the Contract and for compliance with the Contract Documents. Note corrections and field
<br />dimensions. Mark with approval stamp before submitting to Architect.
<br />B. Architect will review each action submittal, make marks to indicate corrections or modifications required, stamp and mark as appropriate to indicate action taken,
<br />and return copies less those retained.
<br />3.2 CONTRACTOR'S CONSTRUCTION SCHEDULE
<br />A. Distribute copies of approved schedule to Owner, Architect, subcontractors, testing and inspecting agencies, and parties identified by Contractorwith a
<br />need -to -know schedule responsibility. When revisions are made, distribute updated schedules to the same parties.
<br />B. Updating: At weekly intervals, update schedule to reflect actual construction progress and activities. Issue schedule one week before each regularly scheduled
<br />progress meeting.
<br />1. As the Work progresses, indicate Actual Completion percentage for each activity.
<br />END OF SECTION 01 30 00
<br />SECTION 01 42 00 - REFERENCES
<br />PART1- GENERAL
<br />1.1 DEFINITIONS
<br />A. General: Basic Contract definitions are included in the Conditions of the Contract.
<br />B. "Approved": When used to convey Owner's action on Contractor's submittals, applications, and requests, "approved" is limited to Owner's duties and
<br />responsibilities as stated in the Conditions of the Contract.
<br />C. "Directed": A command or instruction by Owner. Other terms including "requested," "authorized," "selected," "approved," "required," and "permitted" have
<br />the same meaning as "directed."
<br />D. "Indicated": Requirements expressed by graphic representations or in written form on Drawings, in Specifications, and in other Contract Documents. Other
<br />terms including "shown," "noted," "scheduled," and "specified" have the same meaning as "indicated."
<br />E. "Regulations": Laws, ordinances, statutes, and lawful orders issued by authorities having jurisdiction, and rules, conventions, and agreements within the
<br />construction industry that control performance of the Work.
<br />F. "Furnish": Supply and deliver to Project site, ready for unloading, unpacking, assembly, installation, and similar operations.
<br />G. "Install": Operations at Project site including unloading, temporarily storing, unpacking, assembling, erecting, placing, anchoring, applying, working to dimension,
<br />finishing, curing, protecting, cleaning, and similar operations.
<br />H. "Provide": Furnish and install, complete and ready for the intended use.
<br />1. "Project Site": Space available for performing construction activities. The extent of Project site is shown on Drawings and may or may not be identical with the
<br />description of the land on which Project is to be built.
<br />1.2 INDUSTRY STANDARDS
<br />A. Applicability of Standards: Unless the Contract Documents include more stringent requirements, applicable construction industry standards have the same
<br />force and effect as if bound or copied directly into the Contract Documents to the extent referenced. Such standards are made a part of the Contract Documents
<br />by reference.
<br />B. Publication Dates: Comply with standards in effect as of date of the Contract Documents, unless otherwise indicated.
<br />C. Copies of Standards: Each entity engaged in construction on Project should be familiar with industry standards applicable to its construction activity. Copies of
<br />applicable standards are not bound with the Contract Documents.
<br />1. Where copies of standards are needed to perform a required construction activity, obtain copies directly from publication source.
<br />1.3 ABBREVIATIONS AND ACRONYMS
<br />A. Industry Organizations: Where abbreviations and acronyms are used in Specifications or other Contract Documents, they shall mean the recognized name of
<br />the entities indicated in Gale Research's "Encyclopedia of Associations" or in Columbia Books' "National Trade & Professional Associations ofthe U.S."
<br />PART 2 - PRODUCTS (Not Used)
<br />PART 3 - EXECUTION (Not Used)
<br />END OF SECTION 01 42 00
<br />SECTION 01 50 00 - TEMPORARY FACILITIES AND CONTROLS
<br />PART 1 - GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Use Charges: Cost or use charges for temporary facilities shall be included in the Contract Sum.
<br />B. Use water and electric power from Owner's existing system without metering and without payment of use charges.
<br />C. Electrical Service: Comply with NEMA, NECA, and UL standards and regulations for temporary electric service. Install service to comply with NFPA 70.
<br />PART 2 - PRODUCTS
<br />2.1 EQUIPMENT
<br />A. Heating Equipment: Unless Owner authorizes use of permanent heating system, provide vented, self-contained heaters with thermostatic control.
<br />1. Use of gasoline -burning space heaters, open -flame heaters, or salamander -type heating units is prohibited.
<br />2. Heating Units: Listed and labeled, by a testing agency acceptable to authorities having jurisdiction, and marked for intended use.
<br />PART 3 - EXECUTION
<br />3.1 TEMPORARY UTILITIES
<br />A. General: Arrange with utility company, Owner, and existing users for time when service can be interrupted, if necessary, to make connections for temporary
<br />services.
<br />B. Sanitary Facilities: Use of Owner's existing toilet facilities will be permitted, as long as facilities are cleaned and maintained in a condition acceptable to Owner.
<br />At Substantial Completion, restore these facilities to condition existing before initial use.
<br />C. Heating and Cooling: Provide temporary heating and cooling required for curing or drying of completed installations or for protecting installed construction from
<br />adverse effects of low temperatures or high humidity. Select equipment that will not have a harmful effect on completed installations or elements being installed.
<br />D. Provide temporary lighting with local switching that provides adequate illumination for construction operations, observations, inspections, and traffic conditions.
<br />3.2 TEMPORARY SUPPORT FACILITIES
<br />A. Provide field offices, storage and fabrication sheds, and other support facilities as necessary for construction operations.
<br />B. Provide waste -collection containers in sizes adequate to handle waste from construction operations. Collect waste daily and, when containers are full, legally
<br />dispose of waste off -site. Comply with requirements of authorities having jurisdiction.
<br />C. Install project identification and other signs in locations approved by Owner and Architect to inform the public and persons seeking entrance to Project.
<br />3.3 TEMPORARY SECURITY AND PROTECTION FACILITIES
<br />A. Provide temporary environmental protection, operate temporary facilities, and conduct construction in ways and by methods that comply with environmental
<br />regulations and that minimize possible air, waterway, and subsoil contamination or pollution or other undesirable effects.
<br />B. Provide temporary enclosures for protection of construction and workers from inclement weather and for containment of heat.
<br />C. Provide floor -to -ceiling dustproof partitions to limit dust and dirt migration and to separate areas occupied by Owner and tenants from fumes and noise.
<br />D. Comply with requirements of authorities having jurisdiction for erecting structurally adequate barricades, including warning signs and lighting.
<br />E. Remove and safely store existing window treatment during construction.
<br />1. Clean and reinstall at time of Substantial Completion.
<br />E. Furnish and install site enclosure in a manner that will prevent easy entering except by entrance gates.
<br />F. Install and maintain temporary fire -protection facilities. Comply with NFPA 241.
<br />3.4 TERMINATION AND REMOVAL
<br />A. Temporary Utilities: At earliest feasible time, when acceptable to Owner, change over from use of temporary service to use of permanent service.
<br />B. Remove temporary facilities and controls no later than Substantial Completion. Personnel remaining after Substantial Completion will be permitted to use
<br />permanent facilities, under conditions acceptable to Owner.
<br />END OF SECTION 01 50 00
<br />SECTION 01 60 00 - PRODUCT REQUIREMENTS
<br />PART 1 - GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. The term "product" includes the terms "material," "equipment," "system," and terms of similar intent.
<br />C. Product Substitutions will only be considered when specified product is no longer available.
<br />D. Product Substitutions: Substitutions include changes in products, materials, equipment, and methods of construction from those required by the Contract
<br />Documents and proposed by Contractor after award of the Contract.
<br />1. Submit three copies of each request for product substitution.
<br />2. Submit requests within days after the Notice of Award.
<br />3. Do not submit unapproved substitutions on Shop Drawings or other submittals.
<br />4. Identify product to be replaced and show compliance with requirements for substitutions. Include a detailed comparison of significant qualities of proposed
<br />substitution with those of the Work specified, a list of changes needed to other parts of the Work required to accommodate proposed substitution, and
<br />any proposed changes in the Contract Sum or the Contract Time should the substitution be accepted.
<br />5. Architect will review the proposed substitution and notify Contractor of its acceptance or rejection by Change Order.
<br />E. Deliver, store, and handle products using means and methods that will prevent damage, deterioration, and loss, including theft. Comply with manufacturers
<br />written instructions.
<br />1. Schedule delivery to minimize long-term storage at Project site and to prevent overcrowding of construction spaces.
<br />2. Deliver products to Project site in manufacturer's original sealed container or packaging, complete with labels and instructions for handling, storing,
<br />unpacking, protecting, and installing.
<br />3. Inspect products on delivery to ensure compliance with the Contract Documents and to ensure that products are undamaged and properly protected.
<br />4. Store materials in a manner that will not endanger Project structure.
<br />5. Store products that are subject to damage by the elements, under cover in a weathertight enclosure above ground, with ventilation adequate to prevent
<br />condensation.
<br />F. Warranties specified in other Sections shall be in addition to, and run concurrent with, other warranties required by the Contract Documents.
<br />Manufacturers disclaimers and limitations on product warranties do not relieve Contractor of obligations under requirements of the Contract Documents.
<br />PART 2 - PRODUCTS
<br />2.1 PRODUCT OPTIONS
<br />A. Product Selection Procedures:
<br />1. Where Specifications name a single product or manufacturer, provide the item indicated that complies with requirements.
<br />2. Where Specifications include a list of names of products or manufacturers, provide one of the items indicated that complies with requirements.
<br />B. Unless otherwise indicated, Architect will select color, pattern, and texture of each product from manufacturers full range of options that includes both
<br />standard and premium items.
<br />PART 3 - EXECUTION (Not Applicable)
<br />END OF SECTION 01 60 00
<br />SECTION 01 70 00 - EXECUTION AND CLOSEOUT REQUIREMENTS
<br />PART1- GENERAL
<br />1. 1 CLOSEOUT SUBMITTALS
<br />A. Record Drawings: Maintain a set of prints of the Contract Drawings as Record Drawings. Mark to show actual installation where installation varies from
<br />that shown originally.
<br />1. Identify and date each Record Drawing; include the designation "PROJECT RECORD DRAWING" in a prominent location.
<br />PART 2 - PRODUCTS (Not Applicable)
<br />PART 3 - EXECUTION
<br />3.1 EXAMINATION AND PREPARATION
<br />A. Examine substrates and conditions for compliance with manufacturer's written requirements including, but not limited to, surfaces that are sound, level,
<br />plumb, smooth, clean, and free of deleterious substances; substrates within installation tolerances; and application conditions within environmental limits.
<br />Proceed with installation only after unsatisfactory conditions have been corrected.
<br />B. Before proceeding to lay out the Work, verify layout information shown on Drawings, in relation to property survey and existing benchmarks.
<br />C. Take field measurements as required to fit the Work properly. Where fabricated products are to be fitted to other construction, verify dimensions by field
<br />measurement before fabrication and, when possible, allow for fitting and trimming during installation.
<br />3.2 CUTTING AND PATCHING
<br />A. Do not cut structural members or operational elements without prior written approval of Architect.
<br />B. Where existing services/systems are required to be removed, relocated, or abandoned, bypass such services/systems before cutting to prevent interruption
<br />to occupied areas.
<br />C. Patch with durable seams that are as invisible as possible. Provide materials and comply with installation requirements specified in other Sections.
<br />3.3 INSTALLATION
<br />A. Comply with manufacturer's written instructions for installation. Anchor each product securely in place, accurately located and aligned with other portions
<br />of the Work. Clean exposed surfaces and protect from damage.
<br />B. Clean Project site and work areas daily, including common areas.
<br />3.4 FINAL CLEANING
<br />A. Complete the following cleaning operations before requesting inspection for certification of Substantial Completion:
<br />1. Remove labels that are not permanent.
<br />2. Clean transparent materials, including mirrors. Remove excess glazing compounds. Replace chipped or broken glass.
<br />3. Clean exposed finishes to a dust -free condition, free of stains, films, and foreign substances. Sweep concrete floors broom clean.
<br />4. Vacuum carpeted surfaces and wax resilient flooring.
<br />5. Wipe surfaces of mechanical and electrical equipment. Remove excess lubrication. Clean plumbing fixtures. Clean light fixtures, lamps, globes,
<br />and reflectors.
<br />6. Clean windows and window treatments.
<br />7. Clean Project site, yard, and grounds, in areas disturbed by construction activities.
<br />3.5 CLOSEOUT PROCEDURES
<br />A. Substantial Completion: Before requesting Substantial Completion inspection, complete the following:
<br />1. Prepare a list of items to be completed and corrected (punch list), the value of items on the list, and reasons why the Work is not complete.
<br />2. Advise Owner of pending insurance changeover requirements.
<br />3. Submit specific warranties, maintenance service agreements, and similar documents.
<br />4. Obtain and submit releases permitting Owner unrestricted use of the Work and access to services and utilities. Include occupancy permits, operating
<br />certificates, and similar releases.
<br />5. Submit Record Drawings, operation and maintenance manuals, and similar final record information.
<br />6. Deliver tools, spare parts, extra materials, and similar items.
<br />7. Make final changeover of permanent locks and deliver keys to Owner.
<br />8. Complete startup testing of systems.
<br />9. Remove temporary facilities and controls.
<br />1 0. Submit changeover information related to Owner's occupancy, use, operation, and maintenance.
<br />1 1. Complete final cleaning requirements, including touchup painting.
<br />12. Touch up and otherwise repair and restore marred exposed finishes to eliminate visual defects.
<br />B. Submit a written request for inspection for Substantial Completion. On receipt of request, Architect will proceed with inspection or advise Contractor of
<br />unfulfilled requirements. Architect will prepare the Certificate of Substantial Completion after inspection or will advise Contractor of items that must be
<br />completed or corrected before certificate will be issued.
<br />C. Request inspection for Final Completion, once the following are complete:
<br />1. Submit a copy of Substantial Completion inspection list stating that each item has been completed or otherwise resolved for acceptance.
<br />2. Instruct Owner's personnel in operation, adjustment, and maintenance of products, equipment, and systems.
<br />D. Request reinspection when the Work identified in previous inspections as incomplete is completed or corrected.
<br />E. Submit a written request for final inspection for acceptance. On receipt of request, Architect will proceed with inspection or advise Contractor of unfulfilled
<br />requirements. Architect will prepare final Certificate for Payment after inspection or will advise Contractor of items that must be completed or corrected before
<br />certificate will be issued.
<br />3.6 DEMONSTRATION AND TRAINING
<br />A. Engage qualified instructors to instruct Owners personnel to adjust, operate, and maintain systems, subsystems, and equipment not part of a system.
<br />Include a detailed review of the following:
<br />1. Include instruction for basis of system design and operational requirements, review of documentation, emergency procedures, operations, adjustments,
<br />troubleshooting, maintenance, and repairs.
<br />END OF SECTION 01 70 00
<br />SECTION 01 73 29 - CUTTING AND PATCHING
<br />PART 1 - GENERAL
<br />1.1 SUBMITTALS
<br />A. Cutting and Patching Proposal: Submit a proposal describing procedures at least I 0 days before the time cutting and patching will be performed
<br />requesting approval to proceed. Include the following information:
<br />1. Extent: Describe cutting and patching, show how they will be performed, and indicate why they cannot be avoided.
<br />2. Changes to In -Place Construction: Describe anticipated results. Include changes to structural elements and operating components as wel
<br />as changes in building's appearance and other significant visual elements.
<br />3. Products: List products to be used and firms or entities that will perform the Work.
<br />4. Dates: Indicate when cutting and patching will be performed.
<br />5. Utility Services and Mechanical/Electrical Systems: List services/systems that cutting and patching procedures will disturb or affect. List
<br />services/systems that will be relocated and those that will be temporarily out of service. Indicate how long services/systems will be disrupted.
<br />6. Structural Elements: Where cutting and patching involve adding reinforcement to structural elements, submit details and engineering calculations
<br />showing integration of reinforcement with original structure.
<br />7. Architect's] Approval: Obtain approval of cutting and patching proposal before cutting and patching. Approval does not waive right to later require
<br />removal and replacement of unsatisfactory work.
<br />1.2 QUALITY ASSURANCE
<br />A. Structural Elements: Do not cut and patch structural elements in a manner that could change their load -carrying capacity or load-defiection ratio.
<br />B. Operational Elements: Do not cut and patch operating elements and related components in a manner that results in reducing their capacity to perform
<br />as intended or that results in increased maintenance or decreased operational life or safety.
<br />C. List below is an example only. Revise to suit Project's operating systems. With advice of counsel, delete below if Architect's approval is not required.
<br />If list is deleted, delete option in paragraph above.
<br />D. Miscellaneous Elements: Do not cut and patch miscellaneous elements or related components in a manner that could change their load -carrying
<br />capacity, that results in reducing their capacity to perform as intended, or that results in increased maintenance or decreased operational life or safety.
<br />E. Visual Requirements: Do not cut and patch construction in a manner that results in visual evidence of cutting and patching. Do not cut and patch
<br />construction exposed on the exterior or in occupied spaces in a manner that would, in Architect's opinion, reduce the building's aesthetic qualities. Remove
<br />and replace construction that has been cut and patched in a visually unsatisfactory manner.
<br />1.3 WARRANTY
<br />A. Existing Warranties: Remove, replace, patch, and repair materials and surfaces cut or damaged during cutting and patching operations, by methods
<br />and with materials so as not to void existing warranties.
<br />PART 2 - PRODUCTS
<br />2.1 MATERIALS
<br />A. General: Comply with requirements specified in other Sections.
<br />1. Close and patch holes and opening in existing floor, wall, and ceiling which exist or result from demolition or alteration Work, to match adjacent
<br />undisturbed surfaces.
<br />2. Perform new Work, and restore and refinish existing Work, to comply with applicable requirements of Sections for new Work.
<br />B. In -Place Materials: Use materials identical to in -place materials. For exposed surfaces, use materials that visually match in -place adjacent surfaces
<br />to the fullest extent possible.
<br />1. If identical materials are unavailable or cannot be used, use materials that, when installed, will match the visual and functional performance of
<br />in -place materials.
<br />PART 3 - EXECUTION
<br />3.1 EXAMINATION
<br />A. Examine surfaces to be cut and patched and conditions under which cutting and patching are to be performed.
<br />1. Compatibility: Before patching, verify compatibility with and suitability of substrates, including compatibility with in -place finishes or primers.
<br />2. Proceed with installation only after unsafe or unsatisfactory conditions have been corrected.
<br />3.2 PREPARATION
<br />A. Temporary Support: Provide temporary support of Work to be cut.
<br />B. Protection: Protect in -place construction during cutting and patching to prevent damage. Provide protection from adverse weather conditions for
<br />portions of Project that might be exposed during cutting and patching operations.
<br />C. Adjoining Areas: Avoid interference with use of adjoining areas or interruption of free passage to adjoining areas.
<br />D. Existing Utility Services and Mechanical/Electrical Systems: Where existing services/systems are required to be removed, relocated, or
<br />abandoned, bypass such services/systems before cutting to prevent interruption to occupied areas.
<br />3.3 PERFORMANCE
<br />A. General: Employ skilled workers to perform cutting and patching. Proceed with cutting and patching at the earliest feasible time, and complete
<br />without delay.
<br />1. Cut in -place construction to provide for installation of other components or performance of other construction, and subsequently patch as required to
<br />restore surfaces to their original condition.
<br />B. Patching: Patch construction by filling, repairing, refinishing, closing up, and similar operations following performance of other Work. Patch with durable
<br />seams that are as invisible as possible. Provide materials and comply with installation requirements specified in other Sections.
<br />1. Inspection: Where feasible, test and inspect patched areas after completion to demonstrate integrity of installation.
<br />2. Exposed Finishes: Restore exposed finishes of patched areas and extend finish restoration into retained adjoining construction in a manner that will
<br />eliminate evidence of patching and refinishing.
<br />3. Floors and Walls: Where walls or partitions that are removed extend one finished area into another, patch and repair floor and wall surfaces in the
<br />new space. Provide an even surface of uniform finish, color, texture, and appearance. Remove in -place floor and wall coverings and replace with
<br />new materials, if necessary, to achieve uniform color and appearance.
<br />4. Ceilings: Patch, repair, or rehang in -place ceilings as necessary to provide an even -plane surface of uniform appearance.
<br />5. Exterior Building Enclosure: Patch components in a manner that restores enclosure to a weathertight condition.
<br />C. Cleaning: Clean areas and spaces where cutting and patching are performed. Completely remove paint, mortar, oils, putty, and similar materials.
<br />END OF SECTION 01 73 29
<br />CAMPBELL +VAN DUSEN
<br />ARCHITECTURE INTERIOR DESIGN
<br />www.CVDstudio.com
<br />CAMPBELL + VAN DUSEN Design Studio, LLC.
<br />255 South Orange Avenue Suite # 1 240
<br />Orlando, Florida 32801
<br />Phone: 407.930.6016
<br />FL. Lic. No. AR001 6053
<br />ARCHITECT OF RECORD
<br />FRANK W. CAMPBELL AIA
<br />FLLIC NO. AR0016053
<br />COPY OF THIS PLAN IS NOT VALID UNLESS SIGNED,
<br />SEALED AND DATED BY THE ARCHITECT OF RECORD
<br />COPY OF THIS PLAN IS NOT VALID UNLESS SIGNED,
<br />SEALED AND DATED BY THE ENGINEER OF RECORD
<br />_J
<br />Li-
<br />,
<br />(/)
<br />_J
<br />_J
<br />E
<br />2
<br />0!�
<br />0
<br />>_
<br />T:
<br />F-
<br />CL
<br />0-
<br />=
<br />LU
<br />rV
<br />F--
<br />r14
<br />u
<br />I
<br /><
<br />I
<br />r)
<br />v:i
<br />L/')
<br />>
<br />LLJ
<br />LILJ
<br />I
<br />_J
<br />in
<br />=
<br />I
<br />C0
<br />F-
<br />F-
<br />+
<br />L0
<br />=
<br />_J
<br />__J
<br />(.)
<br />-,7
<br />.,0
<br />af
<br /><
<br />UJ
<br />LLJ
<br />I
<br />>--
<br />()
<br />)
<br />0
<br />>_
<br />I
<br />=
<br />0-
<br />�
<br />1-0 lqq-
<br />ry
<br />C)
<br /><
<br />LU
<br />3�:
<br />ILLJ
<br />'O Lo
<br />00 (y)
<br />0-
<br />r_4
<br />r__1 CY)
<br />CONSTRUCTION DOCUMENTS
<br />_
<br />;
<br />03.24.2023
<br />��� DESCRIPTION
<br />IIIIIIIIIIIIIIIIIIIIIII
<br />����
<br />IIIIIIIIIIIIIIIIIIIIIII - M
<br />IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
<br />IIIIIIIIIIIIIIIIIIIIIII ���
<br />IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII1IIIIIIII11IIIIIIIIIIII1IIII
<br />IIIIIIIIIIIIIIIIIIIIIII ��-
<br />IIIIIIIIIIIIIIIIIIIIIII
<br />IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIN
<br />PRINCIPAL IN CHARGE
<br />F. CAMPBELL
<br />....................................................................
<br />PROJECT MANAGER
<br />M. TORRES
<br />....................................................................
<br />NOTES
<br />A0.2
<br />
|