|
SECTION 01 7419 - CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL
<br />PART 1 - GENERAL
<br />1.1 PERFORMANCE REQUIREMENTS
<br />A. General: Develop waste management plan that results in end -of -Project rates for salvage/recycling of a minimum 50 percent by weight of total waste
<br />generated by the Work.
<br />1.2 SUBMITTALS
<br />A. Waste Reduction Progress Reports: Concurrent with each Application for Payment, submit two copies of report. Include separate reports for demolition
<br />and construction waste. Include the following information:
<br />1. Material category.
<br />2. Generation point of waste.
<br />3. Total quantity of waste in tons.
<br />4. Quantity of waste salvaged, both estimated and actual in tons.
<br />5. Quantity of waste recycled, both estimated and actual in tons.
<br />6. Total quantity of waste recovered (salvaged plus recycled) in tons.
<br />7. Total quantity of waste recovered (salvaged plus recycled) as a percentage of total waste.
<br />B. Records of Donations: Indicate receipt and acceptance of salvageable waste donated to individuals and organizations. Indicate whether organization is
<br />tax exempt.
<br />C. Recycling and Processing Facility Records: Indicate receipt and acceptance of recyclable waste by recycling and processing facilities licensed to accept
<br />them. Include manifests, weight tickets, receipts, and invoices.
<br />D. Landfill and Incinerator Disposal Records: Indicate receipt and acceptance of waste by landfills and incinerator facilities licensed to accept them.
<br />Include manifests, weight tickets, receipts, and invoices.
<br />1.3 WASTE MANAGEMENT PLAN
<br />A. General: Develop plan consisting of waste identification, waste reduction work plan, and cost/revenue analysis. Indicate quantities by weight or
<br />volume, but use same units of measure throughout waste management plan.
<br />B. Waste Identification: Indicate anticipated types and quantities of demolition and construction waste generated by the Work. Include estimated
<br />quantities and assumptions for estimates.
<br />C. Waste Reduction Work Plan: List each type of waste and whether it will be salvaged, recycled, or disposed of in landfill or incinerator. Include
<br />points of waste generation, total quantity of each type of waste, quantity for each means of recovery, and handling and transportation procedures.
<br />1. Salvaged Materials for Reuse: For materials that will be salvaged and reused in this Project, describe methods for preparing salvaged materials
<br />before incorporation into the Work.
<br />2. Salvaged Materials for Donation: For materials that will be donated to individuals and organizations, include list of their names, addresses,
<br />and telephone numbers.
<br />3. Recycled Materials: Include list of local receivers and processors and type of recycled materials each will accept. Include names, addresses,
<br />and telephone numbers.
<br />4. Disposed Materials: Indicate how and where materials will be disposed of. Include name, address, and telephone number of each landfill
<br />and incinerator facility.
<br />5. Handling and Transportation Procedures: Include method that will be used for separating recyclable waste including sizes of containers,
<br />container labeling, and designated location on Project site where materials separation will be located.
<br />PART 2 - PRODUCTS (Not Used)
<br />PART 3 - EXECUTION
<br />3.1 PLAN IMPLEMENTATION
<br />A. General: Implement waste management plan. Provide handling, containers, storage, signage, transportation, and other items as required to
<br />implement waste management plan during the entire duration of the Contract.
<br />B. Training: Train workers, subcontractors, and suppliers on proper waste management procedures, as appropriate for the Work occurring at Project site.
<br />1. Distribute waste management plan to everyone concerned within three days of submittal return.
<br />2. Distribute waste management plan to entities when they first begin work on -site. Review plan procedures and locations established for salvage,
<br />recycling, and disposal.
<br />C. Site Access and Temporary Controls: Conduct waste management operations to ensure minimum interference with roads, streets, walks, walkways,
<br />and other adjacent occupied and used facilities.
<br />3.2 RECYCLING DEMOLITION AND CONSTRUCTION WASTE, GENERAL
<br />A. General: Recycle paper and beverage containers used by on -site workers.
<br />B. Procedures: Separate recyclable waste from other waste materials, trash, and debris. Separate recyclable waste by type at Project site to the
<br />maximum extent practical.
<br />1. Provide appropriately marked containers or bins for controlling recyclable waste until they are removed from Project site. Include list of acceptable
<br />and unacceptable materials at each container and bin.
<br />a. Inspect containers and bins for contamination and remove contaminated materials if found.
<br />2. Stockpile processed materials on -site without intermixing with other materials. Place, grade, and shape stockpiles to drain surface water.
<br />Cover to prevent windblown dust.
<br />3. Stockpile materials away from construction area. Do not store within drip line of remaining trees.
<br />4. Store components off the ground and protect from the weather.
<br />5. Remove recyclable waste off Owner's property and transport to recycling receiver or processor.
<br />3.3 RECYCLING DEMOLITION WASTE
<br />A. Concrete: Remove reinforcement and other metals from concrete and sort with other metals.
<br />B. Wood Materials: Sort and stack members according to size, type, and length. Separate lumber, engineered wood products, panel products,
<br />and treated wood materials.
<br />C. Metals: Separate metals by type.
<br />1. Structural Steel: Stack members according to size, type of member, and length.
<br />2. Remove and dispose of bolts, nuts, washers, and other rough hardware.
<br />D. Gypsum Board: Stack large clean pieces on wood pallets and store in a dry location. Remove edge trim and sort with other metals.
<br />Remove and dispose of fasteners.
<br />E. Acoustical Ceiling Panels and Tile: Stack large clean pieces on wood pallets and store in a dry location.
<br />1. Separate suspension system, trim, and other metals from panels and tile and sort with other metals.
<br />F. Carpet: Roll large pieces tightly after removing debris, trash, adhesive, and tack strips.
<br />1. Store clean, dry carpet in a closed container or trailer provided by Carpet Reclamation Agency or carpet recycler.
<br />G. Equipment: Drain tanks, piping, and fixtures. Seal openings with caps or plugs. Protect equipment from exposure to weather.
<br />H. Plumbing Fixtures: Separate by type and size.
<br />1. Piping: Reduce piping to straight lengths and store by type and size. Separate supports, hangers, valves, sprinklers, and other components by type and size
<br />J. Lighting Fixtures: Separate lamps by type and protect from breakage.
<br />K. Electrical Devices: Separate switches, receptacles, switchgear, transformers, meters, panelboards, circuit breakers, and other devices by type.
<br />L. Conduit: Reduce conduit to straight lengths and store by type and size.
<br />3.4 RECYCLING CONSTRUCTION WASTE
<br />A. Packaging:
<br />1. Cardboard and Boxes: Break down packaging into flat sheets. Bundle and store in a dry location.
<br />2. Polystyrene Packaging: Separate and bag materials.
<br />3. Pallets: As much as possible, require deliveries using pallets to remove pallets from Project site. For pallets that remain on -site, break down
<br />pallets into component wood pieces and comply with requirements for recycling wood.
<br />4. Crates: Break down crates into component wood pieces and comply with requirements for recycling wood.
<br />B. Wood Materials:
<br />1. Clean Cut -Offs of Lumber: Grind or chip into small pieces.
<br />2. Clean Sawdust: Bag sawdust that does not contain painted or treated wood.
<br />C. Gypsum Board: Stack large clean pieces on wood pallets and store in a dry location.
<br />3.5 DISPOSAL OF WASTE
<br />A. General: Except for items or materials to be salvaged, recycled, or otherwise reused, remove waste materials from Project site and legally
<br />dispose of them in a landfill or incinerator acceptable to authorities having jurisdiction.
<br />1. Except as otherwise specified, do not allow waste materials that are to be disposed of accumulate on -site.
<br />2. Remove and transport debris in a manner that will prevent spillage on adjacent surfaces and areas.
<br />B. Disposal: Transport waste materials off Owners property and legally dispose of them.
<br />END OF SECTION 01 74 19
<br />SECTION 02 41 19 - SELECTIVE STRUCTURE DEMOLITION
<br />PART1- GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Comply with EPA regulations and hauling and disposal regulations of authorities having jurisdiction.
<br />B. Owner will occupy portions of building immediately adjacent to selective demolition area. Conduct selective demolition so Owners operations will not
<br />be disrupted.
<br />C. It is not expected that hazardous materials will be encountered in the Work. If materials suspected of containing hazardous materials are encountered,
<br />do not disturb; immediately notify Architect and Owner. Owner will remove hazardous materials under a separate contract.
<br />PART 2 - PRODUCTS (Not Applicable)
<br />PART 3 - EXECUTION
<br />3.1 DEMOLITION
<br />A. Maintain services/systems indicated to remain and protect them against damage during selective demolition operations. Before proceeding with demolition,
<br />provide temporary services/systems that bypass area of selective demolition and that maintain continuity of services/systems to other parts of the building.
<br />B. Locate, identify, shut off, disconnect, and cap off utility services and mechanical/electrical systems serving areas to be selectively demolished.
<br />C. Provide temporary barricades and other protection required to prevent injury to people and damage to adjacent buildings and facilities to remain.
<br />D. Provide and maintain shoring, bracing, and structural supports as required to preserve stability and prevent movement, settlement, or collapse of
<br />construction and finishes to remain or construction being demolished.
<br />E. Provide temporary weather protection to prevent water leakage and damage to structure and interior areas.
<br />F. Protect walls, ceilings, floors, and other existing finish work that are to remain. Erect and maintain dustproof partitions. Cover and protect furniture,
<br />furnishings, and equipment that have not been removed.
<br />G. Neatly cut openings and holes plumb, square, and true to dimensions required. Use cutting methods least likely to damage construction to remain or
<br />adjoining construction.
<br />H. Promptly remove demolished materials from Owners property and legally dispose of them. Do not bum demolished materials.
<br />END OF SECTION 02 41 19
<br />06 50 00 - METAL FABRICATIONS
<br />PART� ENE AL
<br />1.1 SE 10 !QUIREMENTS
<br />'_
<br />A. Submittals: Sho wings showing details of fabrication and installation.
<br />op-Qra
<br />PART 2 - PRODUCTS
<br />2.1 METALS
<br />A. Numinum Extrusions: ASTM Alloy 6063-T6.
<br />B. Numinum-Alloy Rolled Tread [at : M B 632/13 632M, Alloy 6061-T6.
<br />C. Aluminum Castings: ASTM B 6/ 26M, A 443.0-F.
<br />2.2 GROUT
<br />A. Nonshrink, Nonmetallic Grout: ASTM C 1107; recom ded by manufacturer for exterior plications.
<br />2.3 FABRICATION
<br />A. General: Shear and punch metals cleanly and accurately. Rem burrs and e exposed edges. Form bent -metal corners to smallest radius
<br />possible without impairing work.
<br />B. Welding: Weld comers and seams continuously. Use materials and tho hat minimize distortion and develop strength and corrosion
<br />resistance of base metals. At exposed connections, finish welds su ce smo ith contour of welded surface matching those adjacent.
<br />2.4 STEEL AND IRON FINISHES
<br />A. Prepare uncoated ferrous metal surfaces to comply i SSPC-SP 3, "Power Tool Cleaning, d paint with a st-curing, lead- and
<br />chromate -free, universal modified -alkyd primer co ying with MPI#79.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />.. -
<br />A. Perform cutting, drilling, and fi - required for installing miscellaneous metal fabrications. Set metal fabrication a rately in location,
<br />alignment, and elevation; wi ges and surfaces level, plumb, true, and free of rack.
<br />B. Fit exposed conneci s accurately together to form hairline joints.
<br />C. Coat conceal rfaces of aluminum that will come into contact with grout, concrete, masonry, wood, or dissimilar metals with a coat of
<br />bituminous * t.
<br />END ECTION 05 50 00
<br />SECTION 07 84 13 - PENETRATION FIRESTOPPING
<br />PART1- GENERAL
<br />1.1 PERFORMANCE REQUIREMENTS
<br />A. General: For the following constructions, provide penetrating firestopping that are produced and installed to resist spread of fire according to
<br />requirements indicated, resist passage of smoke and other gases, and maintain original fire -resistance rating of assembly penetrated.
<br />1. Fire -resistance -rated non -load -bearing walls, including partitions, with fire -protection -rated openings.
<br />2. Comply with jurisdictional requirements for locations and firestopping systems.
<br />B. F-Rated Systems: Provide penetrating firestopping with F-ratings indicated, as determined per ASTM E 814, but not less than that equaling
<br />or exceeding fire -resistance rating of constructions penetrated.
<br />C. T-Rated Systems: For the following conditions, provide penetrating firestopping with T-ratings indicated, as well as F-ratings, as determined
<br />per ASTME 814, where systems protect penetrating items exposed to potential contact with adjacent materials in occupiable floor areas:
<br />1. Penetrations located outside wall cavities.
<br />2. Penetrations located in construction containing fire -protection -rated openings.
<br />3. Penetrating items larger than 4-inch- diameter nominal pipe or 16 sq. in. in overall cross -sectional area.
<br />D. For penetrating firestopping exposed to view, traffic, moisture, and physical damage, provide products that after curing do not deteriorate when
<br />exposed to these conditions both duriong and after construction.
<br />1. For piping penetrations for plumbing provide moisture -resistant penetrating firestopping.
<br />2. For penetrations involving insulated piping, provide penetrating firestopping not requiring removal of insulation.
<br />E. For penetrating firestopping exposed to view, provide products with flame -spread ratings of less than 25 and smoke -developed ratings of less
<br />than 450, as determined per ASTM E 84.
<br />1.2 SUBMITTALS
<br />A. Product Data: For each type of penetrating firestopping system product indicated.
<br />B. Shop Drawings: For each penetrating firestopping, show each kind of construction condition penetrated, relationships to adjoining construction,
<br />and kind of penetrating item. Include firestop design designation of testing and inspecting agency acceptable to authorities having jurisdiction that
<br />evidences compliance with requirements for each condition indicated.
<br />1. Submit documentation, including illustrations, from a qualified testing and inspecting agency that is applicable to each penetrating firestopping
<br />configuration for construction and penetrating items.
<br />2. Where Project conditions require modification of qualified testing and inspecting agency's illustration to suit a particular penetrating firestopping
<br />condition, submit illustration, with modifications marked, approved by penetrating firestopping manufacturers fire -protection engineer.
<br />C. Qualification Data: If requested by Architect, for firms and persons specified in "Quality Assurance" Article to demonstrate their capabilities and
<br />experience. Include lists of completed projects with project names and addresses, names and addresses of architects and owners, and other
<br />information specified.
<br />1.3 QUALITY ASSURANCE
<br />A. Installer Qualifications: An experienced installer who specializes in the installation of firestop and has completed penetrating firestopping similar
<br />in material, design, and extent to that indicated for this Project and whose work has resulted in construction with a record of successful in-service
<br />performance.
<br />B. Source Limitations: Obtain penetrating firestopping, for each kind of penetration and construction condition indicated, from a single manufacturer.
<br />C. Fire -Test -Response Characteristics: Provide penetrating firestopping that comply with the following requirements and those specified in
<br />"Performance Requirements" Article:
<br />1. Firestopping tests are performed by a qualified testing and inspecting agency. A qualified testing and inspecting agency is UL, or another agency
<br />performing testing and follow-up inspection services for firestop systems acceptable to authorities having jurisdiction.
<br />2. Penetrating firestopping are identical to those tested per ASTM E 814. Provide rated systems complying with the following requirements:
<br />a. Penetrating firestopping products bear classification marking of qualified testing and inspecting agency.
<br />b. Penetrating firestopping correspond to those indicated by reference to penetrating firestopping system designations listed by the following:
<br />1) UL in "Fire Resistance Directory."
<br />D. Do not cover up firestop system installations that will become concealed behind other construction until building inspector, if required by authorities
<br />having jurisdiction, have examined each installation.
<br />PART 2 - PRODUCTS
<br />2.1 FIRESTOPPING, GENERAL
<br />A. Compatibility: Provide penetrating firestopping that are compatible with one another, with the substrates forming openings, and with the items,
<br />if any, penetrating penetrating firestopping, under conditions of service and application, as demonstrated by penetrating firestopping manufacturer
<br />based on testing and field experience.
<br />B. Accessories: Provide components for each firestop system that are needed to install fill materials and to comply with "Performance
<br />Requirements" Article. Use only components specified by firestop system manufacturer and approved by the qualified testing and inspecting
<br />agency for firestop systems indicated. Accessories include, but are not limited to, the following items:
<br />1. Permanent forming/damming/backing materials, including the following:
<br />a. Slag4rock-wool-fiber insulation.
<br />b. Sealants used in combination with other forming/damming/backing materials to prevent leakage of fill materials in liquid state.
<br />c. Fire -rated form board.
<br />d. Fillers for sealants.
<br />2. Temporary forming materials.
<br />3. Substrate primers.
<br />4. Collars.
<br />5. Steel sleeves.
<br />2.2 FILL MATERIALS
<br />A. General: Provide penetrating firestopping containing the types of fill materials indicated in the penetrating firestopping. Schedule at the end of
<br />Part 3 by reference to the types of materials described in this Article. Fill materials are those referred to in directories of the referenced testing and
<br />inspecting agencies as fill, void, or cavity materials.
<br />B. Latex Sealants: Single -component latex formulations that after cure do not re -emulsify during exposure to moisture.
<br />C. Firestop Devices: Factory -assembled collars formed from galvanized steel and lined with intumescent material sized to fit specific diameter
<br />of penetrant.
<br />D. Intumescent Composite Sheets: Rigid panels consisting of aluminum -foil -faced elastomeric sheet bonded to galvanized steel sheet.
<br />E. Intumescent Putties: Nonhardening dielectric, water-resistant putties containing no solvents, inorganic fibers, or silicone compounds.
<br />F. Intumescent Wrap Strips: Single -component inturnescent elastomeric sheets with aluminum foil on one side.
<br />G. Pillows/Bags: Reusable, heat -expanding pillows/bags consisting of glass -fiber cloth cases filled with a combination of mineral -fiber,
<br />water -insoluble expansion agents and fire -retardant additives.
<br />H. Silicone Foams: Multicomponent, silicone -based liquid elastomers that, when mixed, expand and cure in place to produce a flexible,
<br />nonshrinking foam.
<br />1. Silicone Sealants: Moisture -curing, single -component, silicone -based, neutral -curing elastomeric sealants of grade indicated below:
<br />1. Grade: Pourable (self -leveling) formulation for openings in floors and other horizontal surfaces and nonsag formulation for openings in vertical
<br />and other surfaces requiring a nonslumping, gunnable sealant, unless indicated firestop system limits use to nonsag grade for both opening conditions.
<br />PART 3 - EXECUTION
<br />3.1 EXAMINATION
<br />A. Examine substrates and conditions, with Installer present, for compliance with requirements for opening configurations, penetrating items,
<br />substrates, and other conditions affecting performance.
<br />B. Proceed with installation only after unsatisfactory conditions have been corrected.
<br />3.2 PREPARATION
<br />A. Surface Cleaning: Clean out openings immediately before installing penetrating firestopping to comply with written recommendations of firestop
<br />system manufacturer and the following requirements:
<br />1. Remove from surfaces of opening substrates and from penetrating items foreign materials that could interfere with adhesion of penetrating
<br />firestopping.
<br />2. Clean opening substrates and penetrating items to produce clean, sound surfaces capable of developing optimum bond with penetrating
<br />firestopping. Remove loose particles remaining from cleaning operation.
<br />B. Priming: Prime substrates where recommended in writing by penetrating firestopping manufacturer using that manufacturer's recommended
<br />products and methods. Confine primers to areas of bond; do not allow spillage and migration onto exposed surfaces.
<br />C. Masking Tape: Use masking tape to prevent penetrating firestopping from contacting adjoining surfaces that will remain exposed on completion
<br />of Work and that would otherwise be permanently stained or damaged by such contact or by cleaning methods used to remove smears from firestop
<br />system materials. Remove tape as soon as possible without disturbing firestop system's seal with substrates.
<br />3.3 PENETRATING FIRESTOPPING INSTALLATION
<br />A. General: Install penetrating firestopping to comply with "Performance Requirements" Article and firestop system manufacturers written installation
<br />instructions and published drawings for products and applications indicated.
<br />B. Install forming/damming/backing materials and other accessories of types required to support fill materials during their application and in the
<br />position needed to produce cross -sectional shapes and depths required to achieve fire ratings indicated.
<br />C. Install fill materials for firestop systems by proven techniques to produce the following results:
<br />1. Fill voids and cavities formed by openings, forming materials, accessories, and penetrating items as required to achieve fire -resistance ratings
<br />indicated.
<br />2. Apply materials so they contact and adhere to substrates formed by openings and penetrating items.
<br />3. For fill materials that will remain exposed after completing Work, finish
<br />3.4 IDENTIFICATION
<br />A. Identify penetrating firestopping with pressure -sensitive, self-adhesive, preprinted vinyl labels. Attach labels permanently to surfaces of penetrated
<br />construction on both sides of each firestop system installation where labels will be visible to anyone seeking to remove penetrating items or firestop
<br />systems. Include the following information on labels:
<br />1. The words: "Warning- Penetrating Firestopping --Do Not Disturb. Notify Building Owner of Any Damage."
<br />2. Contractors name, address, and phone number.
<br />3. Penetrating Firestopping designation of applicable testing and inspecting agency.
<br />4. Date of installation.
<br />5. Penetrabng Firestopping manufacturers name.
<br />6. Installers name.
<br />3.5 CLEANING AND PROTECTION
<br />A. Clean off excess fill materials adjacent to openings as Work progresses by methods and with cleaning materials that are approved in writing by
<br />Penetrating Firestopping manufacturers and that do not damage materials in which openings occur.
<br />B. Provide final protection and maintain conditions during and after installation that ensure penetrating firestopping are without damage or deterioration
<br />at time of Substantial Completion. If, despite such protection, damage or deterioration occurs, cut out and remove damaged or deteriorated penetrating
<br />firestopping immediately and install new materials to produce penetrating firestopping complying with specified requirements.
<br />END OF SECTION 07 84 13
<br />SECTION 07 92 00 - JOINT SEALANTS
<br />PART1- GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Submittals: Product Data and color Samples.
<br />B. Environmental Limitations: Do not proceed with installation of joint sealants when ambient and substrate temperature conditions are outside limits
<br />permitted by joint sealant manufacturer or are below 40 deg F.
<br />PART 2 - PRODUCTS
<br />2.1 JOINT SEALANTS
<br />A. Compatibility: Provide joint sealants, joint fillers, and other related materials that are compatible with one another and with joint substrates under service
<br />and application conditions.
<br />C. Sealant for Use in Interior Joints in Ceramic Tile and Other Hard Surfaces in Toilet Rooms and Around Plumbing Fixtures:
<br />1. Single -component, mildew -resistant silicone sealant, ASTM C 920, Type S; Grade NS; Class 25; Uses NT, G, A, and 0; formulated with fungicide.
<br />D. Sealant for Interior Use at Perimeters of Door and Window Frames:
<br />1. Latex sealant, single -component, nonsag, mildew -resistant, paintable, acrylic -emulsion sealant complying with ASTMI C 834.
<br />E. Acoustical Sealant for Exposed Interior Joints:
<br />1. Nonsag, paintable, nonstaining, latex sealant complying with ASTM C 834.
<br />F. Acoustical Sealant for Concealed Joints:
<br />1. Nondrying, nonhardening, nonskinning, nonstaining, gunnable, synthetic -rubber sealant recommended for sealing interior concealed joints to reduce
<br />transmission of airborne sound.
<br />2.2 JOINT -SEALANT BACKING
<br />A. General: Provide sealant backings of material and type that are nonstaining; are compatible with joint substrates, sealants, primers, and otherjoint fillers;
<br />and are approved for applications indicated by sealant manufacturer.
<br />B. Cylindrical Sealant Backings: ASTM C 1330, of size and density to control sealant depth and otherwise contribute to producing optimum sealant
<br />performance.
<br />C. Bond -Breaker Tape: Polyethylene tape or other plastic tape recommended by sealant manufacturer for preventing sealant from adhering to rigid,
<br />inflexible joint -filler materials or joint surfaces at back of joint.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. Comply with ASTM C 11 93.
<br />B. Install sealants using proven techniques that comply with the following:
<br />1. Place sealants so they directly contact and fully wet joint surfaces.
<br />2. Completely fill recesses in each joint configuration.
<br />3. Produce uniform depths and shapes relative to joint width.
<br />C. Comply with ASTM C 919 for use of joint sealants in acoustical applications.
<br />D. Clean off excess sealant adjacent to joints as the Work progresses by methods and cleaning materials approved in writing by manufacturer of joint
<br />sealant and of product in which joints occur.
<br />END OF SECTION 07 92 00
<br />SECTION 08 14 16 - FLUSH WOOD DOORS
<br />PART1- GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Submittals: Samples for factory -finished doors.
<br />B. Quality Standard: WDMA I.S.1-A.
<br />C. Fire -Rated Wood Doors: Labeled by a testing and inspecting agency acceptable to authorities having jurisdiction based on testing per NFPA 252.
<br />1. At stairs and exit passageways, provide doors that have a temperature rise rating of 450 deg F.
<br />PART 2 - PRODUCTS
<br />2.1 DOOR CONSTRUCTION, GENERAL
<br />A. WDMA I.S.1-A Performance Grade:
<br />1. Heavy Duty unless otherwise indicated.
<br />B. Core Doors: Provide partical board lumber cores for doors, containing no ureaformaldehyde.
<br />C. Fire -Protection -Rated Doors: Provide core specified or mineral core as needed to provide fire -protection rating indicated. Provide the following for
<br />mineral -core doors:
<br />1. Composite blocking where required to eliminate through -bolting hardware.
<br />2. Laminated -edge construction.
<br />3. Formed -steel edges and astragals for pairs of doors.
<br />2.2 FLUSH WOOD DOORS
<br />A. Doors for Transparent Finish:
<br />1. Interior Solid -Core Doors: Custom grade, five or seven -ply, structural composite lumber cores.
<br />a. Faces: Grade A species as indicated.
<br />b. Veneer Matching: Slip match, end balanced.
<br />c. Pair matching and set matching.
<br />d. Continuous matching for doors with transoms.
<br />2.3 FABRICATION AND FINISHING
<br />A. Factory fit doors to suit frame -opening sizes indicated and to comply with clearances specified.
<br />B. Factory machine doors for hardware that is not surface applied. Locate hardware to comply with DHI-WDHS-3.
<br />C. Factory finish doors indicated for transparent finish with stain and manufacturer's standard finish complying with WDMA System TR-4, conversion
<br />varnish for grade specified for doors.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. Install doors to comply with manufacturer's written instructions, WDMA I.S.1 -A and as indicated.
<br />1. Install fire -rated doors to comply with NFPA 80.
<br />B. Align and fit doors in frames with uniform clearances and bevels. Machine doors for hardware. Seal cut surfaces after fitting and machining.
<br />C. Clearances: As follows, unless otherwise indicated:
<br />1. 1/8 inch at heads, jambs, and between pairs of doors.
<br />2. 1/8 inch from bottom of door to top of decorative floor finish or covering.
<br />3. 1/4 inch from bottom of door to top of threshold.
<br />4. Comply with NFPA 80 for fire -rated doors.
<br />D. Repair, refinish, or replace factory -finished doors damaged during installation, as directed by Architect.
<br />END OF SECTION 08 14 16
<br />SECTION 08 71 00 - DOOR HARDWARE
<br />PART1- GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Submittals: Hardware schedule and keying schedule.
<br />B. Deliver keys to Owner.
<br />C. Fire -Resistance -Rated Assemblies: Provide products that comply with NFPA 80 and are listed and labeled by a testing and inspecting agency
<br />acceptable to authorities having jurisdiction for applications indicated. On exit devices provide label indicating "Fire Exit Hardware."
<br />PART 2 - PRODUCTS
<br />A. Hinges:
<br />1. Hinges with stainless -steel pins for exterior.
<br />2. Nonremovable hinge pins for exterior and public interior exposure.
<br />3. Ball -bearing hinges for doors with closers and entry doors.
<br />4. 3 hinges for 1-3/4-inch- thick doors 90 inches or less in height; 4 hinges for doors more than 90 inches in height.
<br />B. Locksets and Latchsets:
<br />1. BHMA Al 56.2, Series 4000, Grade 1 for bored locks and latches.
<br />2. BHMA Al 56.3, Grade 1 for exit devices.
<br />3. BHMA Al 56.5, Grade 1 for auxiliary locks.
<br />4. BHMA Al 56.13, Series 1 000, Grade 1 for mortise locks and latches.
<br />5. Lever handles on locksets and latchsets.
<br />6. Provide trim on exit devices matching locksets.
<br />C. Key locks to Owner's new master -key system.
<br />1. Cylinders with six -pin tumblers and removable cores.
<br />2. Provide cylinders for overhead doors, storefront doors, and other locking doors that do not require other hardware.
<br />D. Closers:
<br />1. Mount closers on interior side (room side) of door opening. Provide regular -arm, parallel -arm, or top -jamb -mounted closers as necessary.
<br />2. Adjustable delayed opening (accessible to people with disabilities) feature on closers.
<br />E. Provide wall stops or floor stops for doors without closers.
<br />F. Provide hardware finishes as indicated.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. Mount hardware in locations recommended by the Door and Hardware Institute unless otherwise indicated.
<br />END OF SECTION 08 71 00
<br />SECTION 08 80 00 - GLAZING
<br />PART 1 - GENERAL (Not Applicable)
<br />1.1 SECTION REQUIREMENTS
<br />A. Glass Thickness: Comply with ASTM C1 036 for glass lites.
<br />1. Deflection subject to rejection by Architect.
<br />PART 2 - PRODUCTS
<br />2.1 GLASS
<br />A. Heat -Treated Float Glass: ASTM C 1048, Condition A (uncoated) or Condition C (coated), Type 1, Class 1 (clear) or Class 2 (tinted), Quality Q3,
<br />Kind FT (fully tempered) as indicated.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. Comply with combined recommendations of manufacturers of glass, sealants, gaskets, and other glazing materials, unless more stringent requirements
<br />are contained in GANA's "Glazing Manual."
<br />B. Set glass lites in each series with uniform pattern, draw, bow, and similar characteristics.
<br />C. Remove nonpermanent labels, and clean surfaces immediately after installation.
<br />END OF SECTION 08 80 00
<br />SECTION 08 83 00 - MIRRORS
<br />PART 1 - GENERAL
<br />1.1 SUBMITTALS
<br />A. Product Data: For mirror hardware.
<br />1.2 QUALITY ASSURANCE
<br />A. Glazing Publications: Comply with GANA's "Glazing Manual" and GANA Mirror Division's "Mirrors, Handle with Extreme Care: Tips for the
<br />Professional on the Care and Handling of Mirrors" unless more stringent requirements are indicated
<br />PART 2 - PRODUCTS
<br />2.1 SILVERED FLAT GLASS MIRROR MATERIALS
<br />A. Clear Glass Mirrors: ASTM C 1503, Mirror Glazing Quality.
<br />2.2 MISCELLANEOUS MATERIALS
<br />A. Setting Blocks: Elastomeric material with a Type A Shore durometer hardness of 85, plus or minus 5.
<br />B. Edge Sealer: Coating compatible with glass coating and approved by mirror manufacturer for use in protecting against silver deterioration at
<br />mirrored glass edges.
<br />C. Mirror Mastic: An adhesive setting compound, produced specifically for setting mirrors and certified by both mirror manufacturer and mastic
<br />manufacturer as compatible with glass coating and substrates on which mirrors will be installed.
<br />2.3 MIRROR HARDWARE
<br />A. Mirror Clips: As indicated.
<br />B. Mirror Standoff: As indicated.
<br />C. Fasteners: Fabricated of same basic metal and alloy as fastened metal and matching it in finished color and texture where fasteners are exposed.
<br />D. Anchors and Inserts: Provide devices as required for mirror hardware installation. Provide toothed or lead -shield expansion -bolt devices for
<br />drilled -in -place anchors. Provide galvanized anchors and inserts for applications on inside face of exterior walls and where indicated.
<br />2.4 FABRICATION
<br />A. Mirror Sizes: To suit Project conditions, cut mirrors to final sizes and shapes.
<br />B. Cutouts: Fabricate cutouts for notches and holes in mirrors without marring visible surfaces. Locate and size cutouts so they fit closely around
<br />penetrations in mirrors. Cutouts to be approved by Architect.
<br />C. Mirror Edge Treatment: Rounded polished edge.
<br />1. Seal edges of mirrors after edge treatment to prevent chemical or atmospheric penetration of glass coating.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. General: Install mirrors to comply with mirror manufacturer's written instructions and with referenced GANA publications. Mount mirrors accurately
<br />in place in a manner that avoids distorting reflected images.
<br />B. Provide a minimum air space of 1/8 inch (3 mm) between back of mirrors and mounting surface for air circulation between back of mirrors and face of
<br />mounting surface.
<br />C. For wall -mounted mirrors, install with mirror hardware.
<br />1. Attach mirror hardware securely to mounting surfaces with mechanical fasteners installed with anchors or inserts as applicable. Install fasteners so
<br />heads do not impose point loads on backs of mirrors.
<br />D. Protect mirrors from breakage and contaminating substances resulting from construction operations.
<br />E. Do not permit edges of mirrors to be exposed to standing water.
<br />F. Maintain environmental conditions that will prevent mirrors from being exposed to moisture from condensation or other sources for continuous periods
<br />of time.
<br />END OF SECTION 08 83 00
<br />SECTION 09 22 16 - NON-STRUCTURAL METAL FRAMING
<br />PARTI- GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Submittals: Product Data.
<br />B. Fire -Resistance -Rated Assemblies: Provide materials and construction identical to those tested in assemblies per ASTM E 119 by an independent
<br />testing and inspecting agency acceptable to authorities having jurisdiction.
<br />PART 2 - PRODUCTS
<br />2.1 METAL FRAMING AND SUPPORTS
<br />A. Steel Framing Members, General: ASTM C 754.
<br />1. Steel Sheet Components: ASTM C 645. Thickness specified is minimum uncoated base -metal thickness.
<br />2. Protective Coating: ASTM A 653/A 653M, G40, hot -dip galvanized zinc coating.
<br />B. Suspended Ceiling and Soffit Framing:
<br />1. Tie Wire: ASTM A 641/A 641M, Class 1 zinc coating, soft temper, 0.0625-inch diameter, or double strand of 0.0475-inch- diameter wire.
<br />2. Wire Hangers: ASTM A 641 /A 641 M, Class I zinc coating, soft temper, and 0. 1 62-inch diameter.
<br />3. Carrying Channels: Cold -rolled steel, 0.0538 inch thick.
<br />C. Partition and Soffit Framing:
<br />1. Studs and Runners: In depth and thickness as indicated.
<br />2. Flat Strap and Backing: 0.0179 inch thick.
<br />3. Rigid Hat -Shaped Furring Channels: In depth indicated and 0.0179 inch thick.
<br />4. Resilient Furring Channels: 1/2 inch deep, with single- or double -leg configuration.
<br />5. Cold -Rolled Furring Channels: 0.0538 inch thick, 3/4 inch deep.
<br />6. Z-Furring: In depth required by insulation, 1-1/4-inch face flange, 7/8-inch wall -attachment flange, and 0.0179 inch thick.
<br />2.2 ACCESSORIES
<br />A. General: Comply with referenced installation standards.
<br />1. Fasteners for Metal Framing: Of type, material, size, corrosion resistance, holding power, and other properties required to fasten steel members to
<br />substrates.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. Install steel framing to comply with ASTM C 754 and with ASTM C 840 requirements that apply to framing installation and with United States Gypsum's
<br />"Gypsum Construction Handbook."
<br />B. Install supplementary framing, and blocking to support fixtures, equipment services, heavy trim, grab bars, toilet accessories, furnishings, or similar
<br />construction.
<br />C. Isolate steel framing from building structure, except at floor, to prevent transfer of loading imposed by structural movement.
<br />D. Fire -Resistance -Rated Assemblies: Comply with requirements of listed assemblies.
<br />END OF SECTION 09 22 16
<br />SECTION 09 29 00 - GYPSUM BOARD
<br />PART 1 - GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Submittals: Product Data.
<br />B. Fire -Resistance -Rated Assemblies: Provide materials and construction identical to those tested in assemblies per ASTM E 119 by an independent
<br />testing and inspecting agency acceptable to authorities having jurisdiction.
<br />C. STC-Rated Assemblies: Provide materials and construction identical to those tested in assemblies per ASTM E 90 and classified per ASTM E 413 b
<br />qualified independent testing and inspecting agency.
<br />PART 2 - PRODUCTS
<br />2.1 PANEL PRODUCTS
<br />A. Provide in maximum lengths available to minimize end -to -end butt joints.
<br />B. Interior Gypsum Board: ASTM C 36/C 36M or ASTM C 1396/C 1396M, in thickness indicated, with manufacturers standard edges. Type X where
<br />indicated and Sag -resistant type for ceiling surfaces.
<br />2.2 ACCESSORIES
<br />A. Trim Accessories: ASTMI C 1047, formed from galvanized or aluminum -coated steel sheet, rolled zinc, plastic, or paper -faced galvanized -steel sheei
<br />For exterior trim, use accessories formed from hot -dip galvanized -steel sheet, plastic, or rolled zinc.
<br />1. Provide comerbead at outside comers unless otherwise indicated.
<br />2. Provide LC -bead (J-bead) at exposed panel edges.
<br />: A
<br />o.r-roviueCO"LrOijoinLsvvi,eicinuL,CILU .
<br />B. Aluminum Accessories: Extruded -aluminum accessories indicated with Class 11, clear anodic finish; AA-C12C22A31. CAMPBELL + VAN DUSEN
<br />C. Joint -Treatment Materials: ASTM C 475/C 475M. ARCHITECTURE INTERIOR DESIGN
<br />1. Joint Tape: Paper unless otherwise recommended by panel manufacturer.
<br />2. Joint Compounds: Drying -type, ready -mixed, all-purpose compounds.
<br />3. Skim Coat: For final coat of Level 5 finish, use high -build interior coating product designed for application by aidess sprayer and to be used instead of
<br />skim coat to produce Level 5 finish.
<br />D. Acoustical Sealant for Exposed and Concealed Joints: Nonsag, paintable, nons ining latex sealant complying with ASTM C 834. CAMPBELL + VAN DUSEN Design Studio, LLC.
<br />E. Sound -Attenuation Blankets: ASTM C 665, Type I (unfaced). 255 South Orange Avenue Suite # 1 240
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION Orlando, Florida 32801
<br />A. Install gypsum board to comply with ASTM C 840. Phone: 407.930.6016
<br />1. Isolate gypsum board assemblies from abutting structural and masonry work. Provide edge trim and acoustical sealant. FL. Lic. No. AROO 1 6053
<br />22. z3ingle-Layer Fas ning Methods: Fasten gypsum panels supports with screws.
<br />3. Multilayer Fastening Methods: Fasten base layers and face layer separately to supports with screws.
<br />B. Fire -Resistance -Rated Assemblies: Comply with requirements of listed assemblies.
<br />C. Finishing Gypsum Board: ASTM C 840.
<br />1. At concealed areas, unless a higher level of finish is required for fire -resistance -rated assemblies, provide Level 1 finish: Embed tape at joints.
<br />2. At substrates for tile, provide Level 2 finish: Embed tape and apply separate first coat of joint compound to tape, fasteners, and trim flanges.
<br />3. Unless otherwise indicated, provide Level 4 finish: Embed tape and apply separate first, fill, and finish coats of joint compound to tape, fasteners,
<br />and trim flanges.
<br />4. Where indicated, provide Level 5 finish: Embed tape and apply separate first, fill, and finish coats of joint compound to tape, fasteners, and trim flanges.
<br />Apply skim coat to entire surface.
<br />END OF SECTION 09 29 00
<br />SECTION 09 30 00 - TILING
<br />PART1- GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Submittals: Product Data for tile and installation materials and Samples for tile.
<br />B. Floor Tiles: Static coefficient of friction not less than 0.6 for level surfaces and 0.8 for ramps, per ASTM C 1028.
<br />PART 2 - PRODUCTS
<br />2.1 TILE
<br />A. Tile that complies with Standard grade requirements in ANSI Al 37. 1, "Specifications for Ceramic Tile."
<br />2.2 INSTALLATION MATERIALS
<br />A. VOC Limit for Adhesives and Fluid -Applied Waterproofing Membranes: 65 g/L when calculated according to 40 CFR 59, Subpart D
<br />(EPA Method 24).
<br />B. Crack -Suppression Membranes for Thin -Set Tile Installation: Manufacturers standard fabric -reinforced liquid latex product complying with
<br />ANSI Al 18.1 0.
<br />1. Install for flooring tiles of 12 by 12 or larger.
<br />C. Setting and Grouting Materials: Comply with material standards in ANSI's "Specifications for the Installation of Ceramic Tile" that apply to
<br />materials and methods indicated wiht low voc content.
<br />1. Thin -Set Mortar Type: Latex-portland cement.
<br />2. Grout Type: Polymer modified unless otherwise indicated.
<br />3. Grout Color: As indicated on Finish Schedule.
<br />D. Metal Edge Strips: Angle of L-Shap, height to match tile and setting -bed thickness, metal designed specifically for flooring application.
<br />E. Grout Sealer: Manufacturers standard product for sealing grout joints and that does not change color or appearance of grout.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. Comply with tile installation standards in ANSI's "Specifications for the Installation of Ceramic Tile" that apply to materials and methods indicated.
<br />1. For installations indicated below, follow procedures in ANSI's "Specifications for the Installation of Ceramic Tile" for providing 95 percent mortar
<br />coverage.
<br />a. Tile floors composed of tiles 8 by 8 inches or larger.
<br />b. Tile floors composed of rib -backed tiles.
<br />B. Comply with TCA's "Handbook for Ceramic Tile Installation."
<br />C. Floor Tile Installation Method(s):
<br />1. Over Concrete Subfloors: TCA F1 13 (thin -set mortar on concrete).
<br />2. Over Concrete Subfloors for Floor Tile 12 by 12 Inches or Larger: TCA F122 thin -set mortar over crack suppression membrane on concrete.
<br />D. Wall Tile Installation Method(s):
<br />1. Over Gypsum Board: TCA W242 (organic adhesive on gypsum board and metal studs).
<br />2. Over Glass -Mat, Water -Resistant Backer Board: TCA W245 with thin -set mortar (thin -set mortar on glass -mat, water-resistant backer board).
<br />E. Install tiles on floors as selected by architect.
<br />F. Install tiles on walls as selected by architect.
<br />G. Lay tile in grid pattern, unless otherwise indicated. Align joints where adjoining tiles on floor, base, walls, and trim are the same size.
<br />H. Perform rutting and drilling of tile without marring visible surfaces. Carefully grind cut edges of tile abutting trim, finish, or built-in items for straight
<br />aligned joints. Fit tile closely to electrical outlets, piping, fixtures, and other penetrations so plates, collars, or covers overlap tile.
<br />END OF SECTION 09 30 00
<br />SECTION 09 61 13 - ACOUSTICAL PANEL CEILINGS
<br />PART 1-GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Submittals: Product Data and material Samples.
<br />B. Surface -Burning Characteristics of Panels: ASTM E 1264, Class A materials, tested per ASTM E 84.
<br />C. Fire -Resistance -Rated Assemblies: Provide materials and construction identical to those tested in assemblies per ASTM E 119 by an
<br />independent testing and inspecting agency acceptable to authorities having jurisdiction.
<br />D. Seismic Standard: Provide acoustical panel ceilings designed and installed to withstand the effects of earthquake motions according to
<br />the following:
<br />1. CISCA's Recommendations for Acoustical Ceilings: Comply with CISCA's "Recommendations for Direct -Hung Acoustical Tile and Lay -in
<br />Panel Ceilings".
<br />PART 2 - PRODUCTS
<br />2.1 ACOUSTICAL PANELS
<br />A. Provide acoustical panels and suspension system as indicated on Finish Schedule.
<br />B. Attachment Devices: Sized for 5 times the design load indicated in ASTM C 635, Table 1, Direct Hung, unless otherwise indicated. Comply
<br />with seismic design requirements.
<br />C. Wire Hangers, Braces, and Ties: Zinc -coated carbon -steel wire; ASTM A 641 /A 641 M, Class 1 zinc coating, soft temper.
<br />D. Seismic Struts: Manufacturers standard product designed to accommodate seismic forces.
<br />E. Seismic Clips: Manufacturer's standard seismic clips designed to secure panels in place.
<br />F. Roll -Formed, Sheet -Metal Edge Moldings and Trim: Type and profile indicated or, if not indicated, manufacturer's standard moldings for
<br />edges and penetratons that comply with seismic design requirements; formed from sheet metal of same material, finish, and color as that used for
<br />exposed flangesof suspension system runners.
<br />G. Extruded -Aluminum Edge Moldings and Trim: Where indicated, provide manufacturers extruded -aluminum edge moldings and trim of
<br />profile indicated or referenced by manufacturer's designations, including splice plates, corner pieces, and attachment and other clips, complying
<br />with seismic design requirements and the following:
<br />1. Provide trim in full lengths to elevate joint. If joints are reequired, joints to be butted and tight gaps are not acceptable.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. Ceiling Suspension System Installation: Comply with ASTM C 636 and CISCA's "Ceiling Systems Handbook."
<br />1. Fire -Rated Assembly: Install fire -rated ceiling systems according to tested fire -rated design.
<br />B. Install acoustical panels with undamaged edges and fit accurately into suspension system runners and edge moldings. Scribe and cut panels
<br />at borders and penetrations to provide a neat, precise fit.
<br />C. Arrange directionally patterned acoustical panels as indicated on Reflective Ceiling Plan.
<br />END OF SECTION 09 51 13
<br />SECTION 09 65 13 - RESILIENT BASE AND ACCESSORIES
<br />PART1- GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Submittals: Product Data and Samples.
<br />PART 2 - PRODUCTS
<br />2.1 RESILIENT BASE AND ACCESSORIES
<br />A. Provide resilient rubber base transition strips and accessories as indicated on Finish Schedule.
<br />B. Provide manufacturers continuous rolls.
<br />2.2 INSTALLATION ACCESSORIES
<br />A. Trowelable Leveling and Patching Compounds: Latex -modified, portland cement- or blended hydraulic cement -based formulation provided or
<br />approved by flooring manufacturer for applications indicated.
<br />B. Adhesives: Water-resistant type containing low voc recommended by manufacturer to suit products and substrate conditions.
<br />C. Stair -Tread -Nose Filler: Two-part epoxy compound recommended by resilient tread manufacturer to fill nosing substrates that do not
<br />conform to tread contours.
<br />D. Resilient Transition Strips: Rubber, in profile as indicated.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. Prepare concrete substrates according to ASTM F 71 0. Verify that substrates are dry and free of curing compounds, sealers, and hardeners.
<br />B. Adhesively install resilient wall base and accessories.
<br />C. Install wall base in maximum lengths possible. Apply to walls, columns, pilasters, casework, and other permanent fixtures in rooms or areas
<br />where base is required.
<br />D. Install stair -tread -nose filler to nosing substrates that do not conform to tread contours.
<br />E. Install reducer strips at edges of floor coverings that would otherwise be exposed.
<br />F. Transition strips: Butt to adjacent materials and tightly adhere to substrates throughout length of each piece.
<br />END OF SECTION 09 65 13
<br />SECTION 09 65 19 - RESILIENT TILE FLOORING
<br />PART 1 - GENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. Submittals: Product Data and Samples.
<br />B. Fire -Test Response: Resilient tile has critical radiant flux classification of Class 1, not less than 0.45 W/sq. cm per ASTM E 648.
<br />PART 2 - PRODUCTS
<br />2.1 RESILIENT TILE FLOORING
<br />A. Provide resilient tile flooring as indicated on Finish Schedule.
<br />2.2 INSTALLATION ACCESSORIES
<br />A. Trowelable Leveling and Patching Compounds: Latex -modified, portland cement- or blended hydraulic cement -based formulation provided
<br />or approved by flooring manufacturer for applications indicated.
<br />B. Adhesives: Low voc water-resistant type recommended by manufacturer to suit resilient products and substrate conditions indicated.
<br />C. Metal Edge Strips: Extruded aluminum in maximum available lengths to minimize joints.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION
<br />A. Prepare concrete substrates according to ASTM F 71 0. Verify that substrates are dry and free of curing compounds, sealers, and hardeners.
<br />1. Moisture Testing: Perform tests recommended by manufacturer complying with ASTM F1 869 and ASTM F2170.
<br />2. Proceed with installation only after substrates pass testing.
<br />B. Lay out tiles so tile widths at opposite edges of room are equal and are at least one-half of a tile.
<br />C. Match tiles for color and pattern by selecting tiles from cartons in same sequence as manufactured and packaged. Lay tiles in patterns indicated.
<br />END OF SECTION 09 65 19
<br />:��
<br />0
<br />l__
<br />QL
<br />Q:�
<br />(.)
<br />V)
<br />LU
<br />n
<br />�_
<br />U
<br />LU
<br />)
<br />0
<br />0!�
<br />IL
<br />www.CVDsfudio.com
<br />X"�,�,,,,, I
<br />�
<br />-1 7 , 111�A
<br />7
<br />ARCHITECT OF RECORD
<br />FRANK W. CAMPBELL AIA
<br />FLLIC NO. AR0016053
<br />COPY OF THIS PLAN IS NOT VALID UNLESS SIGNED,
<br />SEALED AND DATED BY THE ARCHITECT OF RECORD
<br />COPY OF THIS PLAN IS NOT VALID UNLESS SIGNED,
<br />SEALED AND DATED BY THE ENGINEER OF RECORD
<br />so
<br />rw
<br />MR
<br />no
<br />=
<br />0
<br />RM
<br />Ogg
<br />4
<br />+
<br />LO
<br />1-0
<br />I
<br />I
<br />UJ
<br />C/)
<br />I
<br />I
<br />=
<br />0.0-0
<br />>_
<br />=
<br />Cl-
<br />uj
<br />r1-_J
<br />_J
<br />Li-
<br />,
<br />V)
<br />__J
<br />_J
<br />_17
<br />13:�
<br />>_
<br />=
<br />0-
<br />W
<br />F-4
<br />�
<br />0
<br />>
<br />_J
<br />ca
<br />__J
<br />_J
<br /><
<br />0 �
<br />110 11q_
<br />NO LO
<br />00 (y)
<br />r_1 (y)
<br />CONSTRUCTION DOCUMENTS
<br />03.24.2023
<br />M-110MAII � DESCRIPTION
<br />IIIIIIIIIIIIIIIIIIIIIII
<br />IIIIIIIIIIIIIIIIIIIIIIII IIII1IIIIIIIIIIIIIIII1IIIIIIIIIIIIIIIII_
<br />IIIIIIIIIIIIIIIIIIIIIII __
<br />IIIIIIIIIIIIIIIIIIIIIII ��� IIIIIIIIIIIIIIIIIIIIIII
<br />IIIIIIIIIIIIIIIIIIIIIII ��� - - M
<br />IIIIIIIIIIIIIIIIIIIIIII ��
<br />IIIIIIIIIIIIIIIIIIIIIII ��� ______
<br />IIIIIIIIIIIIIIIIIIIIIII ��� IIIIIIIIIIIIIIIIII
<br />IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIII1IIIIIIII1IIIIIIIIIIIIII11
<br />PRINCIPAL IN CHARGE
<br />F. CAMPBELL
<br />.. .................................................................
<br />PROJECT MANAGER
<br />M. TORRES
<br />.... I ...............................................................
<br />ADVENT HEALTH
<br />WELL 65+
<br />ZEPHYRHILLS
<br />22-0328-01
<br />NOTES
<br />A0.3
<br />
|