|
ARCHITECTURAL SPECIFICATIONS
<br />SECTION 08410
<br />METAL -FRAMED STOREFRONTS
<br />PRODUCTS
<br />MATERIALS - STOREFRONT AND DOORS
<br />A. ALUMINUM STOREFRONT FRAMING MEMBERS, DOOR FRAMES AND
<br />GLASS FRAMING MEMBERS SHALL BE EXTRUDED ALUMINUM SECTIONS
<br />PREPARED FOR FLUSH GLAZING ON ALL SIDES WITH THROUGH SIGHT
<br />LINES AND NO PROJECTING STOPS. DOOR FRAMING MEMBERS SHALL
<br />BE COMPATIBLE WITH GLASS FRAMING IN APPEARANCE, EXCEPT
<br />JAMBS, HEADERS OR TRANSOM BAR AT SINGLE ACTING DOORS SHALL
<br />HAVE BLADE DOOR STOP AND SILL MEMBER OF TRANSOM AT DOOR
<br />HEAD MAY HAVE SURFACE APPLIED GLASS STOPS.
<br />1. STOREFRONT FRAMING MEMBERS AND DOOR FRAMES SHALL BE
<br />1-3/4" x 4-1/2" AND 4-1/2" x 4-1/2".
<br />2. STOREFRONT SHALL BE DESIGNED FOR RESILIENT GLAZING.
<br />FURNISH
<br />NEOPRENE GLAZING STRIPS, GLASS SHIFT ARRESTORS AND ALL
<br />RELATED INSTALLATION AND GLAZING ACCESSORIES.
<br />A. GLAZING STRIPS SHALL BE 6" LONGER AT EACH END THAN
<br />ALUMINUM STOP.
<br />B. ALUMINUM DOORS SHALL BE MEDIUM STILE DESIGN, WITH EXTRUDED
<br />ALUMINUM STILES AND RAILS. MAJOR PORTION OF DOOR STILES AND
<br />RAILS SHALL BE. 125 INCHES IN THICKNESS, GLAZING MOLDINGS
<br />SHALL BE .050 INCHES THICK. BOTTOM RAIL SHALL BE 10" HIGH.
<br />1. ALUMINUM DOORS SHALL BE 1-3/4" THICK.
<br />2. ALL DOORS, EXCEPT INTERIOR VESTIBULE DOORS, SHALL BE
<br />WEATHER-STRIPPED ON 3 SIDES (JAMBS, HEAD AND MEETING STILES)
<br />WITH DOOR MANUFACTURERS STANDARD WEATHER-STRIPPING.
<br />3. GLAZING MOLDINGS SHALL BE SNAP -IN TYPE WITH NEOPRENE
<br />GLAZING STRIPS.
<br />4. BOTTOM DOOR CLEARANCE SHALL BE AS REQUIRED FOR STANDARD
<br />1/2" THRESHOLD INCLUDING ALL DOORS WHERE THRESHOLD IS NOT
<br />REQUIRED.
<br />C. ALL SCREWS, MISCELLANEOUS FASTENING DEVICES AND INTERNAL
<br />COMPONENTS SHALL BE STAINLESS STEEL, PLATED OR CORROSION -
<br />RESISTANT MATERIALS.
<br />D. MASTIC SHALL BE AS RECOMMENDED BY STOREFRONT SYSTEM
<br />MANUFACTURER.
<br />MATERIALS - HARDWARE
<br />A. HARDWARE FOR DOORS IN THIS SECTION SHALL BE FURNISHED AND
<br />INSTALLED BY THIS CONTRACTOR EXCEPT AS NOTED.
<br />B. HARDWARE FOR ALUMINUM DOORS SHALL BE AS SCHEDULED BELOW
<br />IN PARAGRAPHS "C" THROUGH "Q" OF THIS SECTION.
<br />1. LOCK CYLINDERS SHALL BE PROVIDED IN FINISH HARDWARE
<br />SECTION.
<br />C. PUSH BARS PULL HANDLES
<br />KAWNEER STYLE "L" KAWNEER STYLE "L"
<br />PPG STANDARD PPG STANDARD
<br />VISTAWALL STANDARD VISTAWALL STANDARD
<br />D. OFFSET PIVOTS: TOP PIVOT DOROMATIC #280AC BOTTOM PIVOT
<br />DOROMATIC #01175
<br />E. BUMPER ASSEMBLY: KAWNEER #37-485. (TWO SETS PER DOOR LEAF
<br />INSTALLED AS INDICATED ON DRAWINGS.)
<br />1. ALTERNATES: US ALUMINUM #KM-250, VISTAWALL #B-11
<br />OR AMARLITE #70448.
<br />F. PREPARE ALUMINUM DOORS TO RECEIVE BEST CYLINDER AS SPECIFIED IN
<br />SECTION 08710.
<br />G. CYLINDER GUARD FOR OUTSIDE CYLINDER: ADAMS RITE MS 4043 US26D.
<br />H. INTERIOR MORTISE CYLINDER US26D: (SEE "F" ABOVE).
<br />1. WHERE INTERIOR MORTISE CYLINDER IS NOT PERMITTED BY LOCAL
<br />BUILDING CODE, PROVIDE THUMB TURN IN LIEU OF CYLINDER.
<br />I. THUMB TURN: ADAMS RITE TT4066 US28 AT INSIDE OF EXTERIOR
<br />ALUMINUM DOORS.
<br />J. DEADLOCK: ADAMS RITE MS1851AW US28.
<br />K. ARMORED STRIKE: ADAMS RITE MS4002-111 US28.
<br />L. EXTENSION FLUSH BOLTS: ASA STANDARD
<br />IVES C457PA28
<br />CORBIN 8491/4 US28
<br />1. WHERE FLUSH BOLTS ARE NOT PERMITTED ON INACTIVE DOOR BY
<br />LOCAL CODE, OMIT DEADLOCK AND FLUSH BOLT AND FURNISH
<br />THREE POINT DEADLOCK (SEE 2.2, M. BELOW)
<br />M. THREE POINT DEADLOCK: ADAMS RITE MS1851AW x 4015-18-4085
<br />US28.
<br />N. CLOSER: LCN 4111 CUSH 9011 X AL X HAND X 18 PLATE, LCN 4011 H 901.
<br />1. OPERATING PRESSURE SHALL BE A MAXIMUM OF 5 POUNDS
<br />PRESSURE FOR INTERIOR DOORS AND 8.5# PRESSURE FOR
<br />EXTERIOR DOORS.
<br />0. WEATHERSTRIPPING: NATIONAL GUARD, PEMKO, REESE.
<br />P. THRESHOLD AND HOLDER: REESE S247A x 234A x S247A x 270.
<br />Q. EXIT DEVICES:
<br />#1 DOROMATIC 1690 X ALUMINUM (CONCEALED VERTICAL ROD)
<br />#2 DOROMATIC 1790 X ALUMINUM (RIM EXIT DEVICE)
<br />MANUFACTURERS
<br />A. STOREFRONT & DOOR FRAMING MEMBERS
<br />1. KAWNEER CO. INC., "TRI-FAB VG 450"
<br />2. VISTAWALL ARCH PROD., "SERIES FG 2000"
<br />B. DOORS
<br />1. KAWNEER COMPANY, INC., "MEDIUM STILE 350"
<br />2. VISTAWALL, "MEDIUM STILE 375"
<br />FABRICATION
<br />A. FURNISH PRE -FORMED STEEL CHANNEL STIFFENERS AT ALL DOOR
<br />JAMBS AND ELSEWHERE AS INDICATED ON DRAWINGS.
<br />1. INSULATE ALL ALUMINUM IN DIRECT CONTACT WITH INCOMPATIBLE
<br />MATERIALS WITH HEAVY COAT OF ZINC CHROMATE OR BITUMINOUS
<br />PAINT.
<br />B. ALL CUTOUTS, RECESSES, MORTISING OR MILLING OPERATIONS
<br />REQUIRED FOR HARDWARE SHALL BE ACCURATELY MADE AND
<br />REINFORCED WITH BACKING PLATES, TO INSURE ADEQUATE
<br />STRENGTH OF CONNECTION.
<br />C. ALUMINUM FRAME AND DOORS SHALL BE REINFORCED AND
<br />FABRICATED TO RECEIVE PIVOTS. PIVOTS SHALL BE SCREWED TO 1/4'
<br />MINIMUM STEEL BAR REINFORCING. STEEL BARS SHALL BE SCREWED
<br />TO ALUMINUM FRAME AND DOORS WITH SELF-LOCKING "NYLOK"
<br />SCREWS. PIVOTS SHALL BE SCREWED TO STEEL BARS WITH SELF-
<br />LOCKING "NYLOK" SCREWS.
<br />D. PROVIDE POSITIVE METHOD OF SEALING GASKET IN ALUMINUM FRAMES
<br />TO GLASS BY INDUSTRY ACCEPTED METHOD.
<br />FINISH
<br />A. FINISH OF ALL ALUMINUM SHALL BE CLEAR ANODIZED CONFORMING
<br />TO ALUMINUM ASSOCIATION STANDARDS AA-M12C22A31.
<br />EXECUTION
<br />INSTALLATION
<br />A. INSTALL ALUMINUM DOORS AND FRAMING IN ACCORDANCE WITH
<br />MANUFACTURER'S INSTRUCTIONS.
<br />1. BOTTOM DOOR CLEARANCE SHALL BE AS REQUIRED FOR STANDARD
<br />1/2" THRESHOLD INCLUDING ALL DOORS WHERE THRESHOLD IS NOT
<br />REQUIRED.
<br />2. SURFACE MOUNT DOOR HOLDERS TO THE VESTIBULE SIDE TOP RAIL
<br />OF THE DOOR WITH THROUGH STAINLESS STEEL SEX BOLTS ON ONE
<br />PAIR OF EXTERIOR AND VESTIBULE DOORS ONLY. HOLDERS SHALL
<br />LOCK DOOR IN 90E POSITION.
<br />B. EXCEPT WHERE UNAVOIDABLE FOR APPLICATION OF HARDWARE, DO
<br />NOT USE EXPOSED FASTENERS. FOR THE APPLICATION OF HARDWARE
<br />USE FASTENERS THAT MATCH THE FINISH OF MEMBER OR HARDWARE
<br />BEING FASTENED.
<br />C. WEATHER-STRIPPING INSTALLATION: ALIGN WITH WEATHER-STRIPPING
<br />WITH INSIDE FACE OF STOREFRONT FRAME.
<br />SECTION 08721
<br />AUTOMATIC DOOR OPERATORS
<br />DESCRIPTION
<br />A. PROVIDE ALL MATERIALS, LABOR, EQUIPMENT, SERVICE, ETC.,
<br />NECESSARY AND INCIDENTAL TO FURNISH ALL AUTOMATIC DOOR
<br />OPERATORS SHOWN ON THE DRAWINGS AND AS SPECIFIED HEREIN.
<br />B. WORK INCLUDED CONSISTS OF BUT IS NOT LIMITED TO THE FOLLOWING:
<br />1. FURNISHING AND INSTALLING A COMPLETE SYSTEM OF
<br />AUTOMATIC DOOR OPERATOR EQUIPMENT ON DOORS AS
<br />SHOWN ON PLANS AND SPECIFIED HEREIN.
<br />QUALITY ASSURANCE
<br />A. THE EQUIPMENT SHALL BE BY ONE OF THE FOLLOWING APPROVED
<br />MANUFACTURERS/PRODUCTS:
<br />BESAM, INC. - SWINGMASTER 300 (NEW) OR 450 (RETROFIT)
<br />GYRO -TECH. INC. - GT SYSTEM 300 (NEW) OR 400 (RETROFIT)
<br />DOR-O-MATIC - ASTRO-SWING
<br />STANLEY MAGIC -DOOR - MAGIC -SWING
<br />1. REFERENCE IS MADE TO STANLEY PRODUCTS AS CRITERIA.
<br />PRODUCTS
<br />OPERATORS
<br />A. STANLEY MAGIC -SWING "IN -HEADER" CONCEALED OPERATOR SHALL BE
<br />AN ELECTRO-MECHANICAL SYSTEM, SEALED AGAINST DUST, DIRT, AND
<br />CORROSION IN A CAST ALUMINUM CASE.
<br />1. FINISH OF HEADER CASE SHALL MATCH STOREFRONT.
<br />2. FURNISH HEADER CASE TO ALUMINUM STOREFRONT
<br />SUBCONTRACTOR FOR INSTALLATION.
<br />3. PIVOTS SHALL BE FURNISHED BY AUTOMATIC DOOR OPERATOR
<br />MANUFACTURER.
<br />B. THE OPERATOR SHALL OPEN THE DOOR WITH A 1/8 HP, DC MOTOR
<br />REDUCTION GEARS, BALL SCREW ACTUATOR, FORGED STEEL RACK AND
<br />PINION, OPENING TIME TO BACKCHECK (APPROXIMATELY 750) SHALL BE
<br />1.25-1.6 SECONDS. THE OPERATOR SHALL STOP THE DOOR IN THE OPEN
<br />POSITION BY ELECTRICALLY REDUCING THE MOTOR VOLTAGE AND
<br />STALLING AGAINST AN ADJUSTABLE 900 STOP.
<br />C. THE OPERATOR SHALL CLOSE THE DOOR BY SPRING ENERGY. CLOSING
<br />SPEED SHALL BE CONTROLLED BY EMPLOYING THE MOTOR AS A
<br />DYNAMIC BRAKE, AND CLOSING TO LATCH CHECK (APPROXIMATELY 100)
<br />SHALL BE IN 3 SECONDS. CLOSING THROUGH THE LAST 100 SHALL BE IN
<br />1.5 SECONDS MINIMUM.
<br />D. THE OPERATOR SHALL HAVE BUILT-IN EMERGENCY RELEASE WITH
<br />CONTROLLED SPRING RETURN TO THE CLOSED POSITION WITHOUT
<br />MANUAL RESETTING. WHILE THE DOOR IS IN THE EMERGENCY RELEASE
<br />MODE, A DISCONNECT SWITCH SHALL PREVENT POWERED OPERATION.
<br />NOT MORE THAN 50 LBF AT THE LOCK STILE SHALL BE REQUIRED FOR
<br />EMERGENCY USE, PER ANSI A-1 56.10-1985.
<br />E. THE OPERATOR SHALL FUNCTION AS A MANUAL DOOR CLOSER IN THE
<br />DIRECTION OF SWING WITH OR WITHOUT ELECTRICAL POWER.
<br />1. PROVIDE ON/OFF SWITCH AT HEADER CASE,
<br />F. THE FORCES AND SPEEDS OF POWER OPENING, MANUAL OPENING IN
<br />BOTH DIRECTIONS OF SWING, AND SPRING CLOSING IN DIRECTIONS OF
<br />SWING SHALL CONFORM TO THE REQUIREMENTS OF ANSI A-156.10-
<br />LATEST ADDITION.
<br />CONTROLS
<br />A. CONTROLS SHALL CONSIST OF STANLEY MODEL SENTREX A3" SWING
<br />DOOR SENSOR SYSTEM (RETROFIT APPLICATIONS) OR OTHER APPROVED
<br />LISTED DOOR OPERATOR MANUFACTURERS.
<br />RAILS
<br />A. RAILS SHALL BE MINIMUM 30" HIGH X WIDTH OF DOOR AND SHALL HAVE
<br />ONE INTERMEDIATE RAIL. WIRE MESH OR PLASTIC INFILL ONLY WHERE
<br />REQUIRED BY CODE.
<br />EXECUTION
<br />INSTALLATION
<br />A. THE INSTALLATION SHALL BE BY MANUFACTURER'S APPROVED INSTALLER
<br />OR DISTRIBUTOR.
<br />B. THE INSTALLER/DISTRIBUTOR WILL WORK WITH THE GENERAL
<br />CONTRACTOR TO COORDINATE ALL OF THOSE DETAILS NECESSARY
<br />PERTINENT TO THE INSTALLATION OF THE MECHANICAL AND ELECTRICAL
<br />PHASES AS OUTLINED BY THE DETAILS OF THE MANUFACTURER.
<br />COMPLETE MANUFACTURING DRAWINGS AND DETAILS SHALL BE
<br />FURNISHED FOR THE INSTALLATION OF THE EQUIPMENT. FINAL
<br />CONNECTIONS SHALL BE MADE BY THE DISTRIBUTOR/INSTALLER WHO
<br />WILL TUNE -IN THE EQUIPMENT AND LEAVE IT IN SATISFACTORY
<br />OPERATING CONDITION. THE MANUFACTURER SHALL HAVE A FACTORY
<br />TRAINED ENGINEER AVAILABLE FOR JOB ORIENTATION WHEN REQUIRED
<br />BY ANY OF THE TRADES.
<br />C. PROVIDE AND INSTALL "OUT" AND "DO NOT ENTER" DECALS ON
<br />AUTOMATIC DOOR AS SPECIFIED IN ANSI A-156-10.
<br />WARRANTY
<br />THE MANUFACTURER SHALL WARRANT ALL EQUIPMENT; INCLUDING
<br />OPERATORS, CARPETS, CONTROLS AND ETC.; AND THE INSTALLATION OF
<br />THE EQUIPMENT FOR A PERIOD OF TWO (2) FULL YEARS FROM THE
<br />INSTALLATION DATE OF THIS EQUIPMENT, THE MANUFACTURER AND/OR
<br />THE MANUFACTURER'S DISTRIBUTOR SHALL REPLACE ALL DEFECTIVE
<br />EQUIPMENT AT NO ADDITIONAL COST TO THE KMART DURING THIS TWO
<br />(2) YEAR WARRANTY PERIOD. THE DISTRIBUTOR SHALL HAVE AVAILABLE
<br />ON A LOCAL AREA LEVEL ANY PARTS AND SERVICES REQUIRED
<br />THROUGHOUT THE LIFE OF THIS EQUIPMENT.
<br />STORAGE UNIT
<br />ALL SPECIFICATIONS ARE FOR STORAGE SHEDS AS MANUFACTURED BY
<br />"ARROW" OR APPROVED EQUAL
<br />STYLE/MODEL: VINYL MILFORD / #VM108
<br />WALL COLOR: ALMOND WITH GRAY BARK TRIM
<br />ROOF COLOR: HICKORY BROWN
<br />SIZE: 10 FT x 12 FT
<br />INTERIOR DIMENSIONS:
<br />WIDTH: 1181/4DEPTH: 90" HEIGHT: 84 3/4'
<br />WALL HEIGHT: 661/2"
<br />DOOR OPENING:
<br />WIDTH: 551/2" HEIGHT:641/2'
<br />SHIPPING WEIGHT (Ibs): 290
<br />MATERIAL:
<br />WALLS: VINYL COATED STEEL PANELS
<br />ROOF:
<br />HEAVY DUTY STEEL TRUSS SUPPORTS
<br />ARROW KIT "13131<1012"
<br />ANCHOR. -
<br />MODEL AK100 FOR ANCHORING INTO CONCRETE
<br />SECTION 09260
<br />GYPSUM BOARD SYSTEMS
<br />1. GENERAL
<br />1.1 DESCRIPTION
<br />A. FURNISH ALL MATERIALS, ACCESSORIES, LABOR, EQUIPMENT, SERVICES, ETC., NECESSARY
<br />AND INCIDENTAL FOR THE COMPLETION OF ALL GYPSUM BOARD SYSTEM WORK AS SHOWN ON
<br />THE DRAWINGS AND AS SPECIFIED HEREIN.
<br />1.2 DELIVERY, STORAGE AND HANDLING
<br />A. DELIVER MATERIALS IN ORIGINAL PACKAGES, CONTAINERS OR BUNDLES BEARING BRAND
<br />NAME AND IDENTIFICATION OF MANUFACTURER OR SUPPLIER.
<br />B. STORE MATERIALS INSIDE UNDER COVER AND KEEP THEM DRY AND PROTECTED AGAINST
<br />DAMAGE FROM WEATHER, DIRECT SUNLIGHT, SURFACE CONTAMINATION, CORROSION,
<br />CONSTRUCTION TRAFFIC AND OTHER CAUSES. NEATLY STACK GYPSUM BOARDS FLAT TO
<br />PREVENT SAGGING.
<br />C. HANDLE GYPSUM BOARDS TO PREVENT DAMAGE TO EDGES, ENDS, AND SURFACES. DO NOT
<br />BEND OR OTHERWISE DAMAGE METAL CORNER BEADS AND TRIM.
<br />2. PRODUCTS
<br />2.1 MATERIALS
<br />A. GYPSUM BOARD FOR WALLS SHALL BE 1/2" THICK TAPERED EDGE GYPSUM PANELS,
<br />B. EXTERIOR TYPE GYPSUM BOARD SHALL BE 1/2" THICK AND SHALL BE DESIGNATED FOR
<br />EXTERIOR APPLICATIONS.
<br />1. SHEETROCK EXTERIOR GYPSUM CEILING BOARD.
<br />C. TRIM ACCESSORIES SHALL BE GALVANIZED STEEL PERFORATED METAL OR EXPANDED
<br />FINE -MESH FLANGES.
<br />1, CORNER BEAD SHALL BE #800 SERIES OR DUR-A-BEAD.
<br />2. EDGE TRIM SHALL BE #200 SERIES AND #800 SERIES.
<br />3. CONTROL JOINT SHALL BE #093.
<br />D. REINFORCING JOINT TAPE SHALL BE PERF-A-TYPE,
<br />E. JOINT COMPOUND EXCEPT FINISH COAT SHALL BE "DURABOND" SERIES. TYPE SHALL BE AS
<br />RECOMMENDED BY MANUFACTURER (I.E. PREFILL, TOPPING, LAMINATING, ETC.)
<br />F. JOINT COMPOUND FOR WATER RESISTANT GYPSUM BOARD SHALL BE "W/R COMPOUND"
<br />G. JOINT COMPOUND FOR FINISH COAT SHALL BE "JOINT COMPOUND - TOPPING"
<br />H. FASTENINGS, CLIPS, SCREWS, NAILS, ETC., SHALL BE TYPE, SIZE AND DESIGN AS
<br />RECOMMENDED BY DRYWALL SYSTEM MANUFACTURER FOR USE INTENDED.
<br />J. ACOUSTICAL SEALANT SHALL BE AS MANUFACTURED BY TREMCO AND DAP.
<br />2.2 MANUFACTURERS
<br />A. UNITED STATES GYPSUM - SPECIFIED
<br />B. GEORGIA-PACIFIC CORPORATION
<br />C. GOLD BOND BUILDING PRODUCTS
<br />D. DOMTAR GYPSUM, INC.
<br />3. EXECUTION
<br />3.1 EXAMINATION
<br />A. EXAMINE SUBSTRATES TO WHICH DRYWALL CONSTRUCTION ATTACHES OR ABUTS, PRESET
<br />HOLLOW METAL FRAMES, CAST -IN -ANCHORS, AND STRUCTURAL FRAMING, WITH INSTALLER
<br />PRESENT, FOR COMPLIANCE WITH REQUIREMENTS FOR INSTALLATION TOLERANCES AND OTHER
<br />CONDITIONS AFFECTING PERFORMANCE OF DRYWALL CONSTRUCTION.
<br />B. DO NOT PROCEED WITH INSTALLATION UNTIL UNSATISFACTORY CONDITIONS HAVE BEEN
<br />CORRECTED.
<br />3.2 INSTALLATION
<br />A. INSTALL GYPSUM DRYWALL SYSTEMS AS SPECIFIED AND IN ACCORDANCE WITH APPLICABLE
<br />PORTIONS OF U.S. GYPSUM CO. PUBLICATION "DRYWALL CONSTRUCTION HANDBOOK", LATEST
<br />EDITION.
<br />1. DO NOT CONNECT OR SUSPEND STEEL FRAMING FROM DUCTS, PIPES, CONDUIT OR METAL
<br />ROOF DECK. KEEP HANGERS AND BRACES TWO INCHES CLEAR OF DUCTS, PIPES AND CONDUITS.
<br />B. INSTALLATION OF GYPSUM BOARD
<br />1. LOCATE EXPOSED END -BUTT JOINTS AS FAR FROM CENTER OF WALLS AND CEILINGS AS
<br />POSSIBLE, AND STAGGER NOT LESS THAN 24 INCHES IN ALTERNATE COURSES OF BOARD.
<br />2, ATTACH GYPSUM BOARD TO SUPPLEMENTARY FRAMING AND BLOCKING PROVIDED FOR
<br />ADDITIONAL SUPPORT AT OPENINGS AND CUTOUTS.
<br />3. SPOT GROUT HOLLOW METAL DOOR FRAMES FOR SOLID CORE WOOD DOORS, HOLLOW
<br />METAL DOORS AND DOORS OVER 32 INCHES WIDE. APPLY SPOT GROUT AT EACH JAMB ANCHOR
<br />CLIP JUST BEFORE INSERTING BOARD INTO FRAME.
<br />4. AT ALL EXPOSED EDGES, EXTERIOR CORNERS, WHERE GYPSUM BOARD WALLS OR CEILINGS
<br />TERMINATE AGAINST MASONRY, WOOD FRAMES, OTHER DISSIMILAR MATERIALS AND ELSEWHERE
<br />AS INDICATED ON DRAWINGS PROVIDE METAL TRIM.
<br />C. COMPLETELY CONCEAL METAL CORNER REINFORCEMENT AND METAL EDGE TRIM IN JOINT
<br />COMPOUND.
<br />1. PROVIDE METAL CONTROL JOINTS AS RECOMMENDED BY DRYWALL MANUFACTURER.
<br />2. COMPLETELY FILL JOINT BETWEEN BOTTOM OF GYPSUM BOARD PANEL AND CONCRETE
<br />FLOOR SLAB WITH JOINT COMPOUND AND SAND SMOOTH WITH BOARD SURFACE.
<br />3. APPLY JOINT TREATMENT AT GYPSUM BOARD WALL AND CEILING JOINTS (BOTH DIRECTIONS),
<br />FLANGES OF CORNER BEAD, EDGE TRIM, CONTROL JOINTS, PENETRATIONS, FASTENER HEADS
<br />SURFACE DEFECTS AND ALL JOINTS AT CHANGE OF DIRECTION..
<br />4. APPLY TREATMENT IN A MANNER THAT ACHIEVES A SMOOTH, UNIFORM FINISH.
<br />SECTION 09900
<br />PRODUCT
<br />MATERIALS
<br />THINNERS: USE ONLY MATERIALS RECOMMENDED BY PAINT MANUFACTURER.
<br />MANUFACTURERS:
<br />A. PAINT
<br />1. SEARS
<br />FINISHES
<br />COLORS - REFER TO DRAWINGS. WHERE NOT INDICATED ON DRAWINGS, COLORS SHALL BE AS
<br />SELECTED BY OWNER'S REPRESENTATIVE.
<br />A. INTERIOR
<br />1. CONCRETE MASONRY:
<br />A. PRIME COAT - (1 COAT):
<br />B. FINISH (1 COAT TO PROVIDE PINHOLE FREEaFULLHIDING COVERAGE):
<br />C. SEE DRAWINGS FOR COLOR AND TYPE OF FINISH.
<br />2. GYPSUM BOARD:
<br />A. PRIME COAT - (1 COAT):
<br />B. FINISH COAT - (1 COAT TO PROVIDE FULL HIDING COVERAGE):
<br />C. SEE DRAWINGS FOR COLOR AND TYPE OF FINISH.
<br />3. HOLLOW METAL DOORS AND FRAMES:
<br />A. FINISH COAT - (2 COATS):
<br />4. ALL MISCELLANEOUS EXPOSED METAL ITEMS IN FINISHED AREAS (HANDRAILS, RAILING
<br />BRACKETS, JAMB AND SILL.ANGLES, STEEL LINTELS):
<br />A. FINISH COAT- (2 COATS):
<br />EXECUTION
<br />EXAMINATION
<br />THIS CONTRACTOR IS RESPONSIBLE FOR INSPECTING THE WORK OF OTHERS PRIOR TO THE
<br />APPLICATION OF ANY PAINT OR FINISHING MATERIAL.
<br />APPLICATION
<br />A. PAINT MAY BE APPLIED BY SPRAY, ROLLER OR BRUSH UNLESS OTHERWISE SPECIFIED. METHOD
<br />SELECTED MUST BE IN ACCORDANCE WITH MATERIAL MANUFACTURER'S SPECIFICATIONS
<br />AND/OR RECOMMENDATIONS, SUITABLE FOR SURFACE TO WHICH MATERIAL IS APPLIED AND
<br />FINISH SPECIFIED.
<br />1. CARE MUST BE EXERCISED AND PROTECTION PROVIDED FOR ADJACENT PREFINISHED OR
<br />UNFINISHED ITEMS, MOVING PARTS, OR ASSEMBLIES, SPRINKLER HEADS, VALVES, MOTORS,
<br />MACHINERY, ETC. PROVIDE ALL REQUIRED COVERING, MASKING TAPE, ETC.
<br />B. FINISH COLORS SHALL BE AS INDICATED ON THE DRAWINGS OR AS DIRECTED BY OWNER'S
<br />REPRESENTATIVE. TINT PRIMER AND UNDERCOAT TO THE APPROXIMATE SHADE OF THE FINISH
<br />COAT.
<br />C. AT COMPLETION OF CONSTRUCTION ACTIVITIES OF OTHER TRADES, TOUCH UP AND RESTORE
<br />DAMAGED OR DEFACED PAINTED SURFACES.
<br />D. ALL COATS MUST BE THOROUGHLY DRY BEFORE APPLYING SUCCEEDING COATS.
<br />E. ALL WORK WHERE A COAT OF MATERIAL HAS BEEN APPLIED, MUST BE INSPECTED AND
<br />APPROVED BY THE GENERAL CONTRACTOR BEFORE THE APPLICATION OF THE SUCCEEDING
<br />SPECIFIED COAT, OTHERWISE NO CREDIT FOR THE COAT APPLIED WILL BE GIVEN, AND THIS
<br />CONTRACTOR SHALL THEN ASSUME THE RESPONSIBILITY AND RE -COAT THE WORK IN
<br />QUESTION.
<br />1. PUTTY NAIL HOLES, CRACKS AND OTHER DEFECTS IN ALL WOODWORK AND PLYWOOD
<br />SCHEDULED TO BE FINISHED AFTER THE FIRST COAT, WITH PUTTY COLORED TO MATCH THE
<br />FINISH. BRING PUTTY FLUSH WITH THE ADJOINING SURFACE.
<br />2. BETWEEN COATS, SAND ENAMEL OR VARNISH FINISH APPLIED TO WOOD OR METAL WITH
<br />FINE SANDPAPER AND CLEAN TO PRODUCE AN EVEN SMOOTH FINISH.
<br />DESCRIPTION
<br />PROVIDE ALL MATERIALS, LABOR, EQUIPMENT, SERVICE, SCAFFOLDING, ETC., NECESSARY AND
<br />INCIDENTAL TO THE COMPLETION OF ALL PAINTING AS SHOWN ON THE DRAWINGS AND AS
<br />SPECIFIED HEREIN.
<br />REVISIONS
<br />BIDDERS PRINTS ISSUED
<br />JANUARY 17, 2007
<br />BULLETIN #1
<br />APRIL 16, 2007
<br />Cl�
<br />+4
<br />�O
<br />cd
<br />Or,
<br />w C)
<br />U
<br />cn
<br />co
<br />Q
<br />CI]
<br />x
<br />Q
<br />0
<br />L
<br />�L
<br />O
<br />J
<br />LL. NQ
<br />L.L
<br />J Q
<br />J_
<br />L.L
<br />0
<br />m
<br />CL
<br />W -�
<br />NCD
<br />J
<br />1
<br />r
<br />C4 N
<br />1` N
<br />CM
<br />it
<br />�L
<br />LO
<br />CD
<br />Co
<br />m
<br />1
<br />w
<br />m
<br />100
<br />'T
<br />co
<br />co
<br />z
<br />40
<br />-
<br />Q
<br />S
<br />U
<br />�
<br />cn
<br />_J
<br />~
<br />v
<br />z
<br />WIr
<br />za�Q
<br />Cn
<br />Q
<br />�
<br />I-
<br />LN
<br />J
<br />Q
<br />cn
<br />Ln
<br />U
<br />LL
<br />Project Arch./ Engineer:
<br />R.THORNTON
<br />Drawn:
<br />RKT
<br />Checked:
<br />JOHN LINEGAR
<br />Date:
<br />JANUARY 17, 2007
<br />I "
<br />r11
<br />Sheet No:
<br />SPm2
<br />
|