|
UPDATED 11/02/2020
<br />STEP 1 STEP 2
<br />FIRST, MITER CANT
<br />STRIP AT CORNER
<br />-
<br />RUN ONE SHEET
<br />WRAP FIRST BASE FLASHING
<br />UP BOTH EDGES
<br />- AROUND CORNER PROVIDING
<br />E RELIEF CUTS AT CANT
<br />TRANSITIONS AND OVERLAP
<br />= FLASHING AS SHOWN
<br />MITER CUT IN
<br />FIELD SHEET
<br />OVERLAP & SEAL
<br />FIELD MEMBRANE
<br />FIELD MEMBRANE
<br />NT STRIP
<br />CANT STRIP
<br />CANT STRIP
<br />CANT STRIP
<br />STEP 3 STEP 4
<br />XTEND SECOND CUT PEANUT
<br />IASE FLASHINGw CUT OVER SHAPED TARGET
<br />IVER FIRST EDGE FOR PATCHES AND
<br />'IECE INTO CLEAN LINES } , HEAT WELD TO
<br />:ORNER BASE FLASHING
<br />., AS SHOWN
<br />,.,o e
<br />STRIP FIELD MEMBRANE
<br />CANT FIELD MEMBRANE STRIP CANT STRIP CANT STRIP
<br />Co
<br />PLAN VIEW
<br />OF PEANUT SHAPED
<br />TARGET PATCH
<br />NOTES:
<br />1. SBS HEAT WELDED FLASHINGS CAN ONLY BE USED WITH SBS OR BUR SYSTEMS. APP HEAT WELDED FLASHINGS CAN ONLY BE USED WITH APP
<br />OR BUR SYSTEMS. (PLEASE REFER TO THE APPROPRIATE TABLE IN THE BITUMINOUS FLASHING SPECIFICATION INDICATING ACCEPTABLE
<br />FLASHING PRODUCTS FOR EACH OF THE SBS OR APP HEAT WELDED SYSTEMS,)
<br />2. 3-COURSING WITH MBR UTILITY CEMENT & FABRIC OR MBR FLASHING CEMENT & FABRIC MAY BE
<br />USED IN LIEU OF TARGET PATCHES ALONG EDGE OF BASE FLASHING. REFER TO DETAIL DFE 26.
<br />3. PLEASE SEE BITUMINOUS FLASHING SPECIFICATIONS FOR A FULL DESCRIPTION OF INSTALLATION
<br />INSTRUCTIONS AND REQUIREMENTS WHICH ARE CONSIDERED A PART OF THIS DETAIL
<br />4. CAUTION: IMPROPER USE OF THESE MATERIALS AND APPLICATION EQUIPMENT CAN RESULT IN SEVERE BURNS, AND/ OR DAMAGE TO PROPERTY.
<br />THE MECHANIC MUST INSTALL THESE MATERIALS USING THE TECHNIQUES RECOMMENDED BY JM AND THOSE FOUND IN THE CERTIFIED ROOFING
<br />TORCH APPLICATOR (CERTA) PROGRAM AVAILABLE THROUGH THE NATIONAL ROOFING CONTRACTORS ASSOCIATION.
<br />DRAWING NO.
<br />BASE FLASHING AT INSIDE CORNER
<br />HW-2 •7 MEMBRANE TYPE: Johns Marwlle rs a nrenulaet" of clan roofing products and offers this general conceptual
<br />CURB & CORNER BUR wamatlon b you as a courbay, Ths can olkneMary assistance's not to be used or reted upon by
<br />anyone as a substlbte for goNsssind engin" design and documentation required by bullring
<br />ode. a Noble law B these comments do not waUb
<br />SCALE ISSUE GATE MAXIMUM GUARANTEE TERM:
<br />N.T.S 02-08-19 sprouscyoftheendanofenis Wsd,a or assu
<br />far aJoinstsmNeedtryhnsMnnfor soarnb S y�
<br />adequacy d the design d tees buidoshg a try sale massl not supplied by Johns Menmlle. II
<br />FASCIA COVER
<br />STAINLESS
<br />STEEL
<br />SPRING
<br />&I MgMBRANE COMPATIBLE MASTIC
<br />4'-0"
<br />�V1&R/BITUMINOUS CAP SHEET
<br />-
<br />m
<br />LASHING STRIP
<br />STAINLESS STEEL
<br />FASTENERS 12" (304 mm)
<br />O.C. PROVIDED BY JM
<br />JM INSULATION / COVER BOARD
<br />APPROVED DECK
<br />I \ WOOD
<br />NAILER
<br />SECURELY
<br />RNIM FLED
<br />MOM BRAN E
<br />DGMRE:
<br />LPONXWWC
<br />WALL 1/2"
<br />(13 mm)
<br />BELOW
<br />NAILER
<br />NOTES:
<br />1. REFER TO JOHNS MANVILLE WEBSITE (www.jm.com) FOR MOST UP-TO-DATE INFORMATION.
<br />2. PLEASE SEE SINGLE PLY FLASHING SPECIFICATIONS FOR A FULL DESCRIPTION OF INSTALLATION
<br />INSTRUCTIONS AND REQUIREMENTS WHICH ARE CONSIDERED A PART OF THIS DETAIL.
<br />3. ANY CARPENTRY OR METAL WORK SHOULD BE DESIGNED AND CONSTRUCTED IN ACCORDANCE
<br />WITH LOCAL CODE REQUIREMENTS AND/OR PROJECT SPECIFICATIONS. THESE COMPONENTS
<br />SHOULD BE REVIEWED AND APPROVED BY A LICENSED DESIGN PROFESSIONAL.
<br />DRAWING NO.
<br />(RFS) RAIL FASCIA SYSTEM FOR BUR/MOD. BIT. ROOFS
<br />H1N-
<br />MEMBRANE TYPE: Johns Manville is a manufacturer of conv+mclal roofing products and offers this general conceptual
<br />NEW DETAIL JM BUR information to you as a ow". Thb complimentary assistm Is not to be used or reNel upon by
<br />anyone as a sutsiftle for profess" erglreenng deep and docur edallon requyed by bOdmg
<br />SCALE ISSUE DATE MAXIMUM GUARANTEE TERM: code. contract a applicable law. By eaepi Mese eommerts you agree the do nil eonaleute any
<br />rreeppreseflstons, efdolsenleats d, a an aauanpgon by Johns MvMk d an for adher the
<br />N.T.S 7-30 14 30 YEAR akgreuauy of the dealgrh d alb blidng a any other material not supplied by Jotna rwiejohm
<br />.f�
<br />STEP 1 / \ STEP 2
<br />WRAP FIRST BASE v r
<br />FLASHING AROUND
<br />FIRST, MITER CANT CORNER
<br />STRIP AT CORNER
<br />RUN ONE SHEET PROVIIRELIEF
<br />UP BOTH EDGES CUTS AT CANT
<br />TRANSITIONS
<br />AS SHOWN,.••'
<br />CANT STRIP CANT STRIP CANT STRIP
<br />VERTICAL CUT
<br />IN FIELD SHEET
<br />FIELD MEMBRANE FIELD MEMBRANE
<br />STEP 3 \I \ STEP 4
<br />EXTEND 2nd
<br />BASE FLASHING CUT OVER
<br />OVER FIRST PIECE EDGE FOR
<br />OUT TO CORNER CLEAN LINES
<br />CUT -PEANUT
<br />SHAPED TARGEI
<br />PATCH96 AND
<br />HEAT WELD TO
<br />..-BASE FLASHING
<br />AS SHOWN
<br />co
<br />PLAN VIEW
<br />FIELD MEMBRANE OF PEANUT SHAPED FIELD MEMBRANE
<br />TARGET PATCH
<br />NOTES:
<br />1. SBS HEAT WELDED FLASHINGS CAN ONLY BE USED WITH SBS OR BUR SYSTEMS. APP HEAT WELDED FLASHINGS CAN ONLY
<br />BE USED WITH APP OR BUR SYSTEMS. (PLEASE REFER TO THE APPROPRIATE TABLE IN THE BITUMINOUS FLASHING
<br />SPECIFICATION INDICATING ACCEPTABLE FLASHING PRODUCTS FOR EACH OF THE SBS OR APP HEAT WELDED SYSTEMS.)
<br />2. 3-COURSING WITH MBR UTILITY CEMENT & FABRIC OR MBR FLASHING CEMENT & FABRIC MAY BE USED IN LIEU OF TARGET PATCHES
<br />ALONG EDGE OF BASE FLASHING. REFER TO DETAIL DFE 26,
<br />3. CAUTION: IMPROPER USE OF THESE MATERIALS AND APPLICATION EQUIPMENT CAN RESULT IN SEVERE BURNS, AND/ OR DAMAGE TO
<br />PROPERTY. THE MECHANIC MUST INSTALL THESE MATERIALS USING THE TECHNIQUES RECOMMENDED BY JM AND THOSE FOUND IN THE
<br />CERTIFIED ROOFING TORCH APPLICATOR (CERTA) PROGRAM AVAILABLE THROUGH THE NATIONAL ROOFING CONTRACTORS ASSOCIATION.
<br />4. PLEASE SEE BITUMINOUS FLASHING SPECIFICATIONS FOR A FULL DESCRIPTION OF INSTALLATION INSTRUCTIONS AND REQUIREMENTS
<br />WHICH ARE CONSIDERED A PART OF THIS DETAIL
<br />DRAWING NO.
<br />BASE FLASHING AT OUTSIDE CORNER
<br />HW-2 6 MEMBRANE TYPE: Johns Manville is a manufacturer ofcommert]al rooting products aid offers this general conceptual
<br />information b as a courtesy. This nta aosdsenoe is not to be used a raised
<br />CURB 8 CORNER BUR you r ccmWsne ry � by
<br />arlyore as a suballhrle_ fapprolessbnal anginvering
<br />and documentation r builditV
<br />SCALE ISSUE DATE MAXIMUM GUARANTEE TERM: cods, cdntacd, or app law. By amp these convi ents youagree they do rot constitute any
<br />N.T.S 02-08-19 d ft emits d, or an assumpt ah byend ri Manville d any 6aabi ry err stile the me ��
<br />a eq desgn d mils buNdfng a any oilmen mesas! rrot supposed by Johan Man,4flesa
<br />TOP HEM FILLED
<br />WITH CAULK,
<br />SEAL ALL SIDES
<br />GALVANIZED METAL
<br />FACE PLATE INSTALLED
<br />OVER SCUPPER SLEEVE
<br />PINNED & SEALED TO
<br />EXTERIOR WALL
<br />EXTERIOR WALL
<br />1A
<br />SCUPPER SLEEVE -
<br />THROUGH WALL
<br />ASPHALT PRIMER
<br />JM FESCANT PLUS
<br />TERMINATE TOP OF
<br />BASE FLASHINGS
<br />N
<br />AS SPECIFIED
<br />-A
<br />Z LL
<br />SMOOTH SBS TARGET
<br />S tn
<br />PATCH BEHIND
<br />co
<br />SCUPPER
<br />ADHERED
<br />n
<br />n `tot
<br />DXN_A�*LEX
<br />o
<br />4 (EXTEND, OVgW
<br />3CUPPERJ, ,,
<br />A
<br />3 COURSE ALL
<br />EDGES OF OUTER
<br />FLASHING AT SCUPPER
<br />W/ MBR UTILITY CEMENT
<br />si
<br />SUMP CORNER
<br />o `?.• MITERED TAPERED
<br />EDGE STRIPS
<br />UNDER MEMBRANE
<br />SET FLANGE INTO BED
<br />OF MBR UTILITY CEMENT
<br />NAIL FLANGE OF SCUPPER
<br />THROUGH BASE FLASHING
<br />AND ALL PLIES OF ROOF
<br />`r C1 �'cc. INTO WOOD NAILER BELOW
<br />T �cOI'FRF�pF,p �`c�o WITH RING SHANK NAILS
<br />F
<br />qp�'.., e0'�RpFOGF 'tic
<br />SPSo
<br />WOOD NAILER SECURED TO, 3 +
<br />l
<br />DECK UNDER SCUPPER FLANGE.
<br />(SHOWN OUTSIDE OFfE�(-
<br />NOTES: SUMP FOR CLARITY)
<br />1. ADHESIVE NOT SHOWN UNDER PLIES FOR CLARITY.
<br />2. PRIME ALL SCUPPER FLANGES ON BOTH SIDES WITH ASPHALT PRIMER.
<br />3. ALL SCUPPER FLANGES SHALL BE 4" WIDE. PLEASE REFER TO LOCAL CODES AND
<br />SMACNA FOR METAL SCUPPER AND CONDUCTOR HEAD FABRICATION REQUIREMENTS.
<br />4. REFER TO JOHNS MANVILLE WEBSITE (www.jm.com) FOR MOST UP-TO-DATE INFORMATION.
<br />5. SCUPPER FACEPLATE ON EXTERIOR SHOWN AS AN EXAMPLE.
<br />6. ANY CARPENTRY, METAL WORK, OR MASONRY CONSTRUCTION SHOULD BE DESIGNED AND CONSTRUCTED IN ACCORDANCE WITH
<br />LOCAL CODE REQUIREMENTS AND/OR PROJECT SPECIFICATIONS. THESE COMPONENTS SHOULD BE REVIEWED AND APPROVED
<br />BY A LICENSED DESIGN PROFESSIONAL.
<br />7. PLEASE SEE BITUMINOUS FLASHING SPECIFICATIONS FOR A FULL DESCRIPTION OF INSTALLATION
<br />INSTRUCTIONS AND REQUIREMENTS WHICH ARE CONSIDERED A PART OF THIS DETAIL.
<br />DRAWING NO- PRIMARY METAL SCUPPER IN SUMP
<br />D ■NGE -21 MEMBRANE TYPE:
<br />isle ts a deers mils I conceptual
<br />Jdva Marro rfinerhufaCdurer d commercial rcofi tots end genera
<br />l ptu ng 9a
<br />The men Is not to used a relied u D nbmation b OU as 8 assistance be DRAINS &VENTS BUR y uDD y
<br />anyone os a subetlhtkr e professional su9mmhnign 9 deand doarmertabon required by building
<br />SCALE ISSUE DATE MAXIMUM GUARANTEE TERM: code, ooNrad. or applicable law. By aocepNhg these comments you agree troy do not oonsatuae any
<br />N.T.S 6-12-14 =f"�sofanaa.inahrawmplionby oJ nMarneofairyhablitly for hnsMannvlle. to MM�,g10
<br />d tta design d this lUndfg a any oar mtbdal not auppaed by Jolla vie. f/
<br />HEX HEAD
<br />FASTENERS
<br />WATERPROOF
<br />MEMBRANE
<br />* * 1" DIA. CAP NAILS
<br />6" O.C. AT TOP -
<br />OPTIONAL PRESTO
<br />LOCK METAL
<br />COPING COVER
<br />PRESTO LOCK
<br />ANCHOR CLIP
<br />XF
<br />d=
<br />Z
<br />N
<br />z
<br />� N
<br />�C1
<br />4" MIN. (1 FLASHING)
<br />OR
<br />6" MIN. (2 FLASHINGS)
<br />CLEANBOND CAP
<br />ASPHALT
<br />MASONRY PRIMER
<br />MBR FLASHING CEMENT 0
<br />WALL,• MBR UTILITY CEMENT
<br />FESdANT
<br />PLUS ° -Q�c'p*CLEANBOND SA/SA
<br />.ty '• � qp �.
<br />., pR
<br />NOTES:
<br />1. REFER TO JOHNS MANVILLE WEBSITE (www.jm.com) FOR MOST UP-TO-DATE INFORMATION.
<br />2. *AN SBS BACKER PLY EXTENDING 2" MIN. FROM TOE OF CANT IS REQUIRED FOR EXTENDED TERM 25 AND 30 YEAR GUARANTEES.
<br />3. **A TERMINATION BAR FASTENED 6" O.C. IS AN ACCEPTABLE SECUREMENT ALTERNATIVE ALONG THE TOP EDGE OF THE FLASHING,
<br />4. ANY CARPENTRY, METAL WORK, OR MASONRY CONSTRUCTION SHOULD BE DESIGNED AND CONSTRUCTED IN ACCORDANCE WITH
<br />LOCAL CODE REQUIREMENTS AND/OR PROJECT SPECIFICATIONS. THESE COMPONENTS SHOULD BE REVIEWED AND APPROVED BY A
<br />LICENSED DESIGN PROFESSIONAL. CONTACT JM TECHNICAL FOR METAL OPTIONS TO BE INCLUDED WITHIN THE JM NDL GUARANTEE.
<br />5. VERTICAL JOINTS ARE TO BE OVERLAPPED 4" MINIMUM FOR ALL APPLICATIONS. 3 COURSING WITH MBR UTILITY CEMENT AND
<br />FABRIC OR JM MBR FLASHING CEMENT IS RECOMMENDED ON ALL VERTICAL FLASHING LAPS AND INSIDE/OUTSIDE CORNERS
<br />EXTENDING PAST LEADING EDGE OF CANT STRIP.
<br />6. PLEASE SEE BITUMINOUS FLASHING SPECIFICATIONS FOR A FULL DESCRIPTION OF INSTALLATION
<br />INSTRUCTIONS AND REQUIREMENTS WHICH ARE CONSIDERED A PART OF THIS DETAIL.
<br />7. INSTALL PRESTO LOCK COPING IN ACCORDANCE WITH INSTALLATION INSTRUCTIONS INCLUDED WITH THE PRODUCT.
<br />PREFABRICATED INSIDE/OUTSIDE CORNERS AND END CAPS ARE AVAILABLE TO COMPLETE THE INSTALLATION. SHOP
<br />FABRICATED COPINGS SHOULD BE INSTALLED IN ACCORDANCE WITH SMACNA GUIDELINES.
<br />DRAWING NO. BASE FLASHING FOR MASONRY WALL < 24" W/ COPING
<br />CBE-6 (TL) MEMBRANE TYPE
<br />Johns Montfie e a s andaabey of eomrnerdal lords siproducts nce and oilers this darnel d Won by
<br />BUR nbmhanon to you at a couMsy The oonfp8medary asaipance is not to be used a riled upon by
<br />anyone as a sub $A for prohnslon t anpNnenng design and doc rnen46on required by building
<br />SCALE I ISSUE DATE MAXIMUM GUARANTEE TERM: cafe. contract, or applicable law. By accepting those comments you agree do nillstW cale try
<br />N.T.S 02-06-19 representations, endowments of, or an assumption by Johns Minis ofalyliabary for real, aleas V�%�
<br />adequacy of the design dale built" a sed any other maal nil suppled by Johns MaroNM. i Iry.
<br />Cz_
<br />DRAIN STRAI
<br />SUMP CORNER
<br />® CLAMPING RING
<br />CAP SHEET UNDER
<br />CLAMPING RING
<br />UNDERDECK DRAIN � `J { '> f2,fT11f>fff>>yff>ff)T>ryf>>ffTf
<br />`-� JM CLEANSOND SA/SA BASE
<br />CLAMP (AS REQUIRED) JM CLEANBOND SA/SA BASE
<br />SHEET LEAD, MIN. 30" X 30" \, BELOW CAP SHEET
<br />PRIME LEAD WITH PRIMER ON LEAD SHEET
<br />BOTH SIDES, (SEE NOTES)
<br />ROLL LEAD DOWN BOWL. (SET
<br />IN MBR UTILITY CEMENT OR
<br />MBR FLASHING CEMENT)
<br />, '90
<br />INSULATION TAPERED �M
<br />TO DRAIN R1 App
<br />Rp °
<br />�czO
<br />4E
<br />Ck
<br />NOTES:
<br />1. REFER TO JOHNS MANVILLE WEBSITE (www.jm.com) FOR MOST UP-TO-DATE INFORMATION.
<br />2. ASPHALT AND MBR UTILITY CEMENT NOT SHOWN FOR CLARITY
<br />3. LEAD FLASHING SHALL BE 2.5 LBS. PER SQUARE FOOT MINIMUM.
<br />4, IT IS ACCEPTABLE TO RUN FIELD MEMBRANE PLY THROUGH DRAIN CENTER AND OMIT TARGET SHEET IF DRAIN SUMP IS SHALLOW
<br />ENOUGH TO ALLOW INSTALLATION WITHOUT WRINKLES OR FISHMOUTHS. STEEP SUMPS WILL REQUIRE THE INSTALLATION OF A
<br />TARGET PATCH WITHIN DRAINSUMP.
<br />S. USE ASPHALT PRIMER ON LEAD FLANGES WHEN USING MBR UTILITY CEMENT. USE PERMAFLASH PRIMER ON LEAD FLANGES WHEN
<br />USING MBR FLASHING CEMENT,
<br />6. EXTEND ALL PLIES TO EDGE OF DRAIN BOWL.
<br />7. ANY CARPENTRY, METAL WORK, OR MASONRY CONSTRUCTION SHOULD BE DESIGNED AND CONSTRUCTED IN ACCORDANCE WITH
<br />LOCAL CODE REQUIREMENTS AND/OR PROJECT SPECIFICATIONS. THESE COMPONENTS SHOULD BE REVIEWED AND APPROVED BY A
<br />LICENSED DESIGN PROFESSIONAL.
<br />8. PLEASE SEE BITUMINOUS FLASHING SPECIFICATIONS FOR A FULL DESCRIPTION OF INSTALLATION INSTRUCTIONS AND REQUIREMENTS
<br />WHICH ARE CONSIDERED A PART OF THIS DETAIL.
<br />DRAWING NO.
<br />METAL DRAIN
<br />CBE-11
<br />MEMBRANE TYPE: Johns Mania is a elan facturer of cdrnmertial rdding products and offers Bss qerrieral cmcapDul
<br />DRAINS & VENTS BUR nlermaton to you as a couresy. This compldmedary assistance Is not to be used or idled upon by
<br />none as a suWtilute for rolessioral engineering design and doc me ntaaon required by building
<br />trade contrail a law. sccethese cammente agree do rid caatltufe an
<br />SCALE ISSUE DATE MAXIMUM GUARANTEE TERM: representatloni, end�orsvienb of. an o _on by Johns Many d any lability, for dale ale y W.
<br />N.T.S 12-10-18 Hof• d the dealgn of nos budV a any other material nil suppled by Johns MaMle. ��S mwwo% ie
<br />JM R'-10 ONE WAY ROOF VENT
<br />/ CLEANBOND CA
<br />MBR FLASHING CEMENT,
<br />OR MBR UTILITY CEMENT
<br />ROUND CORNERS OF
<br />a TARGET PATCHES
<br />AS SHOWN ----
<br />7
<br />LOOSE INSULATION
<br />VENT FLANGE SET IN -
<br />MBR FLASHING CEMENT,
<br />OR MBR UTILITY CEMENT
<br />5
<br />.,. G� t4$Z>
<br />>
<br />AP
<br />1 i h
<br />�k
<br />NOTES:
<br />1. REFER TO JOHNS MANVILLE WEBSITE (www.jm.com) FOR MOST UP-TO-DATE INFORMATION.
<br />2. CUT A HOLE IN MEMBRANE PRIOR TO INSTALLATION. REMOVE ALL OR PART OF THE INSULATION TO FACILITATE VENTING.
<br />LOOSE INSULATION CAN REMAIN TO MAINTAIN R VALUE AND PREVENT CONDENSATION.
<br />3. ANY CARPENTRY, METAL WORK, OR MASONRY CONSTRUCTION SHOULD BE DESIGNED AND CONSTRUCTED IN
<br />ACCORDANCE WITH LOCAL CODE REQUIREMENTS AND/OR PROJECT SPECIFICATIONS. THESE COMPONENTS SHOULD BE
<br />REVIEWED AND APPROVED BY A LICENSED DESIGN PROFESSIONAL.
<br />4. PLEASE SEE BITUMINOUS FLASHING SPECIFICATIONS FOR A FULL DESCRIPTION OF INSTALLATION INSTRUCTIONS AND
<br />REQUIREMENTS WHICH ARE CONSIDERED A PART OF THIS DETAIL.
<br />DRAWINNGNO. FP-10 ONE WAY ROOF VENT
<br />CV E-1 0 MEMBRANE TYPE
<br />Johns Manvtle e a manufacturer d can
<br />DRAINS & VENTS BUR marvel roofing products and offers fuss general d upon by
<br />albnrnaton ro you as a courtesy 11me rwmplimaaary assistance a not b be used a resod upon by
<br />as a sutwilute for sbrlal and documentation
<br />anyone bPda engineering ,do not by hisia a
<br />SCALE ISSUE DATE MAXIMUM GUARANTEE TERM: code. contract. a appia N Isw. By accepting Nee oomnsnls you trey do yn°I mmUMe try
<br />N.T.S 12-10-18 resclequutiq of the der tsof. orbuiidiig or any otherassurnplicormterfaf not suppled by fs Marmille of }dnsra s ManWNforlInarow
<br />e.. johm all a
<br />FOR SAWCUT REGLET
<br />USE POLYURETHANE CAULK
<br />�1 „
<br />METAL COUNTER FLASHING
<br />4' MIN. COUNTER FLASHING
<br />OVERLAP OVER TOP OF
<br />°BASE
<br />FLASHING
<br />3 COURSING (OPTIONAL)
<br />*MASONRY FASTENERS
<br />ro s
<br />WITH 1" MIN. PLATE 0
<br />°
<br />O
<br />6" O.C. AT TOP EDGE
<br />a
<br />REGLET
<br />ASPHALT PRIMER
<br />FESCANT PLUS
<br />�`
<br />APPROVED SBS OR
<br />APP FLASHING
<br />>pp
<br />HEAT WELD
<br />BITUMEN
<br />0
<br />- �9F APPROVED SBS OR
<br />APP BACKER PLY
<br />..
<br />.• Rp� A
<br />�, \
<br />4
<br />NOTES: v/
<br />1. SBS HEAT WELDED FLASHINGS CAN ONLY BE USED WITH SBS OR BUR SYSTEMS. APP HEAT WELDED FLASHINGS CAN ONLY
<br />BE USED WITH APP OR BUR SYSTEMS. (PLEASE REFER TO THE APPROPRIATE TABLE IN THE BITUMINOUS FLASHING
<br />SPECIFICATION INDICATING ACCEPTABLE FLASHING PRODUCTS FOR EACH OF THE SBS OR APP HEAT WELDED SYSTEMS.)
<br />2. *A TERMINATION BAR FASTENED 6" O.C. IS AN ACCEPTABLE SECUREMENT ALTERNATIVE ALONG THE TOP EDGE OF THE FLASHING,
<br />3. METAL COUNTER FLASHING IS RECOMMENDED FOR ALL INSTALLATIONS AND IS REQUIRED FOR ALL GUARANTEES 15 YEARS OR LONGER.
<br />A 3 COURSING OF PERMAFLASH MAY BE USED TO SEAL THE TOP EDGE OF THE FLASHING ON 10 YEAR NDUS IN LIEU OF METAL COUNTER
<br />FLASHING.
<br />4. VERTICAL JOINTS ARE TO BE OVERLAPPED 4" MINIMUM FOR ALL APPLICATIONS. 3 COURSING WITH MBR UTILITY CEMENT AND
<br />FABRIC OR JM MBR FLASHING CEMENT IS RECOMMENDED ON ALL VERTICAL FLASHING LAPS AND INSIDE/OUTSIDE CORNERS
<br />EXTENDING PAST LEADING EDGE OF CANT STRIP.
<br />5. ANY CARPENTRY, METAL WORK, OR MASONRY CONSTRUCTION SHOULD BE DESIGNED AND CONSTRUCTED IN ACCORDANCE WITH LOCAL
<br />CODE REQUIREMENTS AND/OR PROJECT SPECIFICATIONS. THESE COMPONENTS SHOULD BE REVIEWED AND APPROVED BY A LICENSED
<br />DESIGN PROFESSIONAL.
<br />6. PLEASE SEE BITUMINOUS FLASHING SPECIFICATIONS FOR A FULL DESCRIPTION OF INSTALLATION INSTRUCTIONS AND
<br />REQUIREMENTS WHICH ARE CONSIDERED A PART OF THIS DETAIL
<br />7. CAUTION: IMPROPER USE OF THESE MATERIALS AND APPLICATION EQUIPMENT CAN RESULT IN SEVERE BURNS, AND/ OR DAMAGE TO
<br />PROPERTY. THE MECHANIC MUST INSTALL THESE MATERIALS USING THE TECHNIQUES RECOMMENDED BY JM AND THOSE FOUND IN THE
<br />CERTIFIED ROOFING TORCH APPLICATOR (CERTA) PROGRAM AVAILABLE THROUGH THE NATIONAL ROOFING CONTRACTORS ASSOCIATION.
<br />DRAWING NO.
<br />BASE FLASHING FOR LOAD BEARING MASONRY WALL W/ COUNTERFLASHING
<br />HW-1(LB)
<br />MEMBRANE TYPE: Johns Manville e a manufacture of canmercel roiling products and offers the al conceptual
<br />FLASHING WALL BUR Mono
<br />sson to you as a cour". The complmardary aaststana a not to be weds retied upon by
<br />anyone as a subslare e1r esslond engneedag clisa n and dowm6nlasah required by building
<br />SCALE ISSUE DATE MAXIMUM GUARANTEE TERM: • oontlact a appal law. By accepting Nose cararfents you a¢ee they do not mrmMlble any
<br />N.T.S 02-08-19 • tents of,, a an assumptim by Johns Manft of any tabi�tlar me
<br />q d the deep of Nis building a any other maerial not supplied by Jots. e.
<br />U0
<br />/tamps
<br />URBANoRDER.tampa, Inc.
<br />5006 south olboron street 33611
<br />813.932.5557
<br />as2002460
<br />IURBANoRDER.tampa, Inca
<br />Throe Plena We wpytlpNed and en aubbct a
<br />mpoght prolection as an'sRNtactan warp' undo!
<br />sactlan 102 of the wityrfIN ea. 17 u.sa. a
<br />ansonded Deeem6er 1990 and known as an:hltecwral
<br />wora copyrlot protection act of 1990. The
<br />pm*ftn Inoudes but Is not anted to the overall
<br />form as won of anangemwnl and composition of
<br />spews and.laments of ohs daepn. u- such
<br />potecton, unsuwodzec use of these plans, wok a
<br />hone represented, can Npoly msu9ln the cessation
<br />of wnstn,oean or buiklwpe b.N saaad end/a
<br />monetary compansatbn to URBANoRDERiwmpa inc.,
<br />Fbrda mosuattlon AA26002400.
<br />ISSUE DATE
<br />05/15/2019
<br />REVISIONS
<br />n
<br />CV
<br />cM
<br />M
<br />U
<br />ICU
<br />�o
<br />z
<br />m
<br />Q
<br />CQ
<br />Cn
<br />`
<br />L
<br />N
<br />Ileass-
<br />W
<br />0
<br />0
<br />Z
<br />0
<br />0
<br />W
<br />JOETOPH.
<br />FL.,REG. AR10095
<br />DATE: 11119/2020
<br />DRWN:
<br />CHKD:
<br />SCALE:
<br />SHEET NUMBER
<br />A=27
<br />VA z Nlis 11119/2020 11:28:46 AM
<br />
|