Laserfiche WebLink
v1Y{IV.11lYIYY �1.11L1�dU <br />DEMOLITION REFLECTED GEILIN(� PLAN <br />SCALE: 1/8" = 1'-0" <br />DEMOLITION REFLECTED CEILING PLAN <br />UNREFERENCED NOTES <br />I. ALL GYPSUM BOARD CEILINGS AND SOFFITS ARE TO BE <br />TAPED, BEDDED AND SANDED TO RECEIVE TENANT FINISH. <br />2. DO NOT SCALE DRAWINGS. WRITTEN DIMENSIONS SHALL <br />GOVERN. LARGE SCALE DRAWINGS SHALL GOVERN OVER <br />SMALLER SCALE DRAWINGS. INFORM ARCHITECT OF ALL <br />DISCREPANCIES PRIOR TO CONSTRUCTION. <br />3. ALL DIMENSIONS ARE FROM FACE OF FINISH / GYP. <br />BOARD FINISH TO FACE OF FINISH / GYP. BOARD FINISH <br />AND / OR FROM FINISHED FLOOR TO FACE OF FINISH / <br />GYP. BOARD -CEILING FINISH UNLESS OTHERWISE NOTED. <br />4. CONTRACTOR TO PATCH AND REPAIR ALL DAMAGED <br />AREAS OF EXISTING GYP. BD. CEILINGS. <br />5. EXISTING LIGHTING SHOWN FOR REFERENCE ONLY. <br />CONTRACTOR TO VERIFY EXISTING CONDITIONS PRIOR TO <br />CONSTRUCTION. <br />6. THE REFLECTED CEILING PLAN IS INTENDED TO SNOW THE <br />EXTENT OF CEILING MATERIALS, SUCH AS LAY -IN TILE OR <br />GYPSUM BOARD, AND THE LOCATION OF SPECIFIED LIGHT <br />FIXTURES ONLY. REFERENCE MECHANICAL AND ELECTRICAL <br />ENGINEERING CONSTRUCTION DOCUMENTS FOR ALL OTHER <br />REQUIREMENTS. <br />__INN11101107ARE____ <br />A OF <br />DEMOLITION REFLECTED CEILING PLAN GENERAL <br />DEMOLITION <br />REFLECTED CEILING PLAN LEGEND <br />NOTES <br />7. ALL MATERIALS LOCATED ABOVE THE CEILING GRID TO <br />.... ....... _ ............. <br />1 <br />EXISTING 2X4 ACOUSTICAL LAY -IN CEILING <br />I. ALL EXISTING LIGHTS TO BE REMOVED AND REPLACED <br />BE NON-COMBUSTIBLE. NO LOOSE OR UNFACED INSULATION <br />TILE AND GRID TO REMAIN <br />WITHIN AREA OF WORK. <br />IN THE RETURN AIR PLENUM. <br />--------.....__..--�--- <br />2. EXISTING 2X4 CEILING GRID TO REMAIN UNLESS NOTED <br />8. LOW VOLTAGE WIRING ABOVE THE CEILING SHALL BE <br />EXISTING EXIT LIGHT FIXTURE TO REMAIN <br />OTHERWISE. <br />INDEPENDENTLY SUPPORTED FROM STRUCTURE. <br />9. SUSPENDED ACOUSTICAL CEILING SYSTEMS SHALL BE <br />DEMOLITION REFLECTED CEILING PLAN <br />INSTALLED IN ACCORDANCE WITH THE PROVISIONS OF <br />EXISTING WALL MOUNTED EMERGENCY <br />LIGHT FIXTURE TO REMAIN <br />REFERENCED NOTES <br />ASTM C 635 AND ASTM C 636. <br />HANGER CEILING WIRES TO BE 12 GA MIN. AT 4'-0" O.C. <br />MAX. ATTACH HILTI XCW U22 (OR EQUAL) W/ CEILING WIRE <br />J — — <br />EXISTING 2X4 ACOUSTICAL LAY -IN CEILING <br />❑1 EXISTING CEILING GRID TO BE REMOVED <br />TO UNDERSIDE OF ROOF DECK. <br />ATTACH WALL ANGLE MOLDING TO GYP. BOARD WALL WITH <br />— — _T_ <br />TILE AND GRID TO BE REMOVED <br />�2 EXISTING HEADER TO BE REMOVED <br />I-I/4" SCREW AT 16" O.C. MAX. <br />— <br />3❑ EXISTING SOFFIT DETAIL IN ENTRY TO REMAIN <br />10. ALL LIGHTS SHALL BE SUPPORTED WITH U12 GA WIRE <br />EXISTING 2x4 LAY -IN LIGHT FIXTURES TO <br />FROM BUILDING STRUCTURE AND NOT FROM CEILING GRID <br />c <br />BE REMOVED <br />® EXISTING COVE LIGHTING IN SOFFIT TO BE REMOVED <br />OR OTHER NON-STRUCTURAL ITEMS. SECURE A MINIMUM OF <br />2 CORNERS (OPPOSITES) TO STRUCTURE ABOVE WITH <br />EXISTING RECESSED CAN LIGHT FIXTURES <br />CHAIN OR WIRE AND FASTEN TO CEILING GRID PER NEC <br />�� <br />TO BE REMOVED <br />410.36. <br />— — EXISTING COVE LIGHTING TO BE REMOVED <br />FARMER <br />ARCHITECTURE <br />License # 1AR107S0 <br />941 Lake Baldwin Lane <br />Orlando, FL 32814 <br />t 321A413320 <br />CONSULTANT: <br />0 <br />LO <br />7M_1�4; <br />0 <br />Lo <br />0 <br />0 <br />FZ <br />� <br />O <br />0 <br />Lu <br />ct <br />LLL <br />J <br />f__ <br />z <br />U) <br />_j <br />Q <br />0 <br />= <br />0= <br />J <br />0 <br />U <br />� <br />w <br />Q <br />r� <br />z <br />J <br />CD <br />t <br />N <br />jr REVISIONS <br />