6512 Gall Blvd (8) - Laserfiche WebLink

Browse Search

ELECTRICAL DEMOLITION PLAN SCALE 3/16" = V-0" DEMOLITION NOTES: 1. COORDINATION: DRAWINGS ARE TO BE USED ONLY AS A GUIDELINE FOR DEMOLITION. COORDINATE ALL DEMOLITION WORK WITH OTHER TRADES, WITH NEW WORK INDICATED ON CONSTRUCTION PLANS, AND WITH ACTUAL FIELD CONDITIONS. 2. LOCKOUT/TAGOUT: VERIFY ALL SOURCES OF ELECTRICAL POWER TO AREA OF WORK ARE DISCONNECTED AND LOCKOUT/TAGOUT PROCEDURES ARE FOLLOWED PER OSHA REQUIREMENTS. 3. NOT IN CONTRACT AREAS: LOCATE, IDENTIFY, AND PROTECT ELECTRICAL SERVICES (E.G. POWER, CONTROL, COMMUNICATION, SECURITY, SIGNAL, LIFE SAFETY, AND FIRE ALARM) PASSING THROUGH DEMOLITION AREA AND SERVING OTHER AREAS OUTSIDE THE RENOVATION LIMITS. MAINTAIN SERVICES TO AREAS OUTSIDE DEMOLITION LIMITS. WHEN SERVICES MUST BE INTERRUPTED, INSTALL TEMPORARY SERVICE FOR AFFECTED AREAS. 4. CONTINUITY OF SERVICE: ANY CIRCUITS FEEDING THROUGH DEVICES OR EQUIPMENT BEING REMOVED, RELOCATED, REWORKED, OR ABANDONED AND SERVING OTHER ELECTRICAL DEVICES, AND/OR EQUIPMENT SHALL BE MAINTAINED BY REWORKING EXISTING WIRING TO RESTORE CONTINUITY OF THE INTERRUPTED CIRCUITS. 5. LIFE SAFETY: EXISTING EMERGENCY LIGHTING, EGRESS LIGHTING, AND FIRE ALARM SYSTEM AND NOTIFICATION APPLIANCES SHALL BE SALVAGED, MAINTAINED IN PROPER OPERATION, AND RECONFIGURED AS REQUIRED TO COMPLY WITH APPLICABLE CODES AND STANDARDS FOR EACH PHASE OF CONSTRUCTION. 6. CODE VIOLATIONS: NOTIFY ENGINEER UPON DISCOVERY OF ANY EXISTING CODE VIOLATIONS FOR CORRECTIVE ACTIONS. 7. EXISTING CIRCUITRY: THE CONTRACTOR MAY REUSE EXISTING CIRCUITRY AS FIELD CONDITIONS PERMIT AND WHERE DESIGN INTENT CAN BE MET. EC SHALL VERIFY THAT TOTAL NEW LOAD DOES NOT EXCEED 80% OF THE BREAKER CONTINUOUS CURRENT RATING. 8. COMPLETE REMOVAL: ELECTRICAL EQUIPMENT AND DEVICES SHALL BE REMOVED COMPLETE INCLUDING CONDUIT, WIRE, HANGERS, AND SUPPORTS BACK TO SOURCE. 9. PROTECTION BARRIERS: PROTECT ADJACENT MATERIALS INDICATED TO REMAIN. INSTALL AND MAINTAIN DUST AND NOISE BARRIERS TO KEEP DIRT, DUST, AND NOISE FROM BEING TRANSMITTED TO ADJACENT AREAS. REMOVE PROTECTION AND BARRIERS AFTER DEMOLITION IS COMPLETE. 10. SALVAGE FOR REUSE: EXISTING EQUIPMENT NOTED TO REMAIN OR BE RELOCATED SHALL BE SALVAGED, REPAIRED, AND CLEANED FOR FUTURE USE. REPLACE MISSING HARDWARE OR DAMAGED EQUIPMENT AS REQUIRED. 11. STORAGE: CONTRACTOR SHALL BE RESPONSIBLE FOR REMOVAL, PRESERVATION, STORAGE, AND PROTECTION OF ALL EQUIPMENT AND DEVICES DESIGNATED TO BE REMOVED AND REINSTALLED. EQUIPMENT SHALL BE STORED IN A MANNER TO AVOID DAMAGE UNTIL REINSTALLED. 12. OWNER RETENTION: THE CONTRACTOR SHALL REMOVE ALL EQUIPMENT NOT INDICATED TO BE REUSED TO A DESIGNATED LOCATION AT THE PROJECT SITE. AFTER THE EQUIPMENT HAS BEEN ASSEMBLED FOR THE OWNER'S INSPECTION AND POSSIBLE RETENTION, ALL EQUIPMENT NOT TO BE RETAINED BY THE OWNER SHALL BE REMOVED FROM THE SITE BY THE CONTRACTOR. 13. PANELBOARD CIRCUIT DIRECTORY: ALL PANELBOARDS SHALL BE FURNISHED WITH REVISED TYPEWRITTEN CIRCUIT DIRECTORY CARDS WITH THE EQUIPMENT AND SPACE SERVED PROPERLY DESIGNATED. EXISTING EQUIPMENT SHALL BE RE -IDENTIFIED AS REQUIRED TO COORDINATE WITH PROPOSED DESIGN. 14. SPARED OUT CIRCUITS: BRANCH CIRCUIT BREAKERS MADE SPARE AS A RESULT OF DEMOLITION ACTIVITIES SHALL BE SWITCHED TO THE 'OFF' POSITION AND LABELED AS "SPARE". 15. RAISED CEILINGS: WHERE ARCHITECTURAL CEILINGS ARE TO BE RAISED, THE EC SHALL REWORK EXISTING OVERHEAD CONDUIT AND CONDUCTORS, IF ANY, TO ALLOW FOR THE CEILING TO BE RAISED. 16. HARD CEILINGS: WHERE NEW HARD CEILING IS TO BE INSTALLED, EC SHALL REWORK AND RELOCATE ALL JUNCTION BOXES OUT FROM ABOVE NEW HARD CEILING. NEW JUNCTION BOX LOCATIONS SHALL BE IN AN ACCESSIBLE AREA ABOVE CEILING. DEMOLITION LEGEND: REFER TO DEMOLITION PLANS FOR ADDITIONAL NOTES AND REQUIREMENTS. (d) SUBSCRIPT DENOTES EXISTING TO BE REMOVED. DISCONNECT AND REMOVE WIRE AND CONDUIT BACK TO SOURCE. MAINTAIN SERVICE TO REMAINING DEVICES. (e) SUBSCRIPT DENOTES EXISTING TO REMAIN. MAINTAIN SERVICE VIA EXISTING CIRCUIT. (r) SUBSCRIPT DENOTES EXISTING TO BE RELOCATED. MATCH EXISTING WIRING AND CONDUIT AND EXTEND TO PROPOSED LOCATION. (er) SUBSCRIPT DENOTES EXISTING DEVICE/FIXTURE TO BE REPLACED IN SAME LOCATION AS EXISTING. DISCONNECT AND REMOVE EXISTING DEVICE/FIXTURE AND MAINTAIN SERVICE VIA EXISTING CIRCUIT. — — — — DASHED LINES INDICATE EXISTING TO BE REMOVED, EXISTING TO BE RELOCATED, OR EXISTING TO BE REPLACED. LIGHT LINES INDICATE EXISTING TO REMAIN. KEYED NOTES: OELECTRICAL DEMOLITION: COORDINATE WITH GENERAL CONTRACTOR AND REFER TO ARCHITECTURAL PLANS FOR DEMOLITION SCOPE. DISCONNECT AND REMOVE EXISTING BRANCH CIRCUIT WIRING AND LOW VOLTAGE TO ACCOMMODATE PROPOSED FLOOR PLAN. OELECTRICAL PANELS: EXISTING ELECTRICAL PANELS AND CONTROL EQUIPMENT TO REMAIN. QEXISTING CEILING GRID AND LIGHT FIXTURES TO BE REMOVED: DISCONNECT AND REMOVE EXISTING INTERIOR LIGHTING IN THIS ROOM/AREA. OEQUIPMENT REMOVAL: EXISTING EQUIPMENT TO BE REMOVED. DISCONNECT EXISITNG BRANCH CIRCUIT CONDUIT AND CONDUCTORS FROM EACH LOAD BACK TO SOURCE. SWITCH EXISTING BRANCH CIRCUIT BREAKER TO "OFF" POSITION AND LABEL AS SPARE. OEXISTING WALK-IN COOLER DOOR TO BE REMOVED: DISCONNECT AND REMOVE EXISTING DOOR LIGHTS. OEXISTING ATM TO BE RELOCATED: REMOVE CONDUIT AND WIRING FROM LOAD BACK TO PREVIOUS SOURCE. OEXISTING HAND DRYER TO BE REMOVED: DISCONNECT AND REMOVE EXISTING HAND DRYER. REMOVE CONDUIT AND WIRE FROM LOAD BACK TO SOURCE. PATCH AND REPAIR SURFACE EFFECTED AREA FROM DEMOLITION. TNOT IN SCOPE OF WORK: UEXISTING AUTOMATIC TANK GAUGE TO BE RELOCATED: REMOVE CONDUIT AND WIRING BACK TO PREVIOUS SOURCE. rn M O 0 m ca w a N O g L N w a', W 0 z INFINITY ENGINEERING GROUP, LLC 1208 East Kennedy Boulevard Suite 230 Tampa, Florida 33602 [p]: 813.434.4770 [fJ: 813.445.4211 www.iegroup.net Cert. of Auth. No. 27889 Client Name and Address 1201 OAKFIELD DRIVE, NO. 109 BRANDON, FLORIDA 33509 0111993idgs� �` FL•f I� 77 o 0 • 0 7 .0 - •'• .t S OF ate: z CV A ch J � z v7 J O W -� -j O w cc o W J 0 m J J y N LO m a� W z a� J W tom_ C L a u� Project No. Sheet 140-88.00 E-101 Date 05/03/2019 Scale k. AS NOTED