|
SECTION 081416
<br />ANY 10 FEEL, WHICHEVER IS LESS.
<br />D. SET THRESHOLDS IN MASTIC AND SECURE.
<br />3. TAPING AND BEDDING OF GYPSUM BOARD.
<br />A TILE:
<br />FLUSH WOOD DOORS
<br />2. MAXIMUM MISALIGNMENT OF MEMBERS ABUTTING END TO END: 1/32 INCH.
<br />E. MOUNT CLOSERS SO THAT CLOSERS AND CLOSER ARMS ARE NOT VISIBLE ON
<br />13 SUBMITTALS
<br />1. SIZE: AS INDICATED ON DRAWINGS.
<br />(CONTINUED)
<br />3. SEALANT SPACE BETWEEN FRAMING MEMBERS AND ADJACENT CONSTRUCTION:
<br />CORRIDOR OR PUBLIC SIDE OF DOORS OR ON EXTERIOR OF BUILDING.
<br />A SUSTAINABLE DESIGN SUBMITTALS.
<br />2. COLOR: AS INDICATED ON DRAWINGS.
<br />1/2 INCH PLUS OR MINUS 1/8 INCH.
<br />F. MOUNTING HEIGHTS - SEE DRAWINGS.
<br />4. RECYCLED CONTENT.
<br />3. TRIM UNITS: BEADS, COVES, AND 5ULLNOSES, COLOR TO MATCH TILE.
<br />32INSTALLATiON
<br />32 ADJUSTING
<br />32 PROTECTION
<br />5. REGIONAL MATERIALS.
<br />A. INSTALL DOORS IN ACCORDANCE WITH WDMA i.SAA.
<br />A. ADJUST HARDWARE FOR SMOOTH OPERATION.
<br />A. REMOVE OR PROTECT HARDWARE UNTIL PAINTING IS COMPLETED.
<br />b. LOW -EMITTING MATERIALS.
<br />23 ACCESSORIES
<br />B. INSTALL DOORS PLUMB AND LEVEL.
<br />B. ADJUST DOORS TO OPERATE WiTH MAXIMUM OPENING FORGEV/41N ACCORDANCE
<br />33ADJUSGING
<br />]A PROJECT CONDITIONS
<br />A. LATEX-PORTLAND CEMENT MORTAR ANSI AIiSA, POLYMER MODIFIED DRY SET
<br />G. FIELD FITTING GO FRAMES:
<br />WITH APPLICABLE ACCESSIBILITY CODE.
<br />A. TEST AND ADJUST HARDWARE FOR QUIET, SMOOTH OPERATION, FREE FROM BINDING
<br />A DO NOT INSTALL GYPSUM BOARD UNTIL BUILDING IS SUBSTANTIALLY
<br />TYPE.
<br />1. NON -RATED DOORS:
<br />C. TOUGH UP MINOR SCRATCHES AND ABRASIONS GO MATCH ORIGINAL FINISH.
<br />AND RATTLING.
<br />WEATHER• IGHT•
<br />B. DRY SET PORTLAND CEMENT MORTAR: ANSI A118.1, POLYMER MODIFIED DRY SET
<br />a. WEIGHT CUT HINGE AND LOCK EDGES EQUALLY.
<br />D. ADJUST WEATHERSTRIPPING TO CONTACT APPROPRIATE SURFACES AND FORM
<br />B. ADJUST DOORS TO OPERATE WITH MAXIMUM OPENING FORCES IN ACCORDANCE
<br />B. MAINTAIN TEMPERATURE IN SPACES IN WHICH WORK iS BEiNG PERFORMED ABOVE
<br />TYPE.
<br />b. HEIGHT: CUT BOTTOM EDGE C>1`tl..Yt MAXIMUM 3/4 INCH.
<br />WEATHER SEAL.
<br />WITH APPLICABLE ACCESSIBILITY CODE.
<br />50 DEGREES F DURING AND AFTER INSTALLATION.
<br />G. EPDXY ADHESIVE:
<br />2. EDGE CLEARANCES:
<br />3.45GHEDULE
<br />1. ANSI A1183, THIN SET BOND TYPE.
<br />a. JAMBS AND HEAD: 118 INCH MAXIMUM BETWEEN DOOR AND FRAME.
<br />A SET NO. I - DOOR FROM SALES AREA GO EXTERIOR (SEE DOOR SCHEDULE ,MID
<br />PART 2 PRODUCTS
<br />2. MAXIMUM VOLATILE ORGANIC COMPOUND (VOG) CONTENT: 65 GRAMS PER LITER
<br />In. SILLS WITHOUT THRESHOLDS: i/8 INCH MAXIMUM BETWEEN DOOR AND TOP OF
<br />SECTION 08 561S
<br />FLOOR PLAN FOR QUANTITY, SIZE AND DIRECTION OF SWING.)
<br />2.1 MANUFACTURERS
<br />-
<br />O. PORTLAND CEMENT: ASTM GI50, TYPE 1, WHITE COLOR
<br />FINISH FLOOR
<br />DRIVE-THRU WINDOW
<br />1. TEMPORARY CYLINDER HAGER 3501 OR 3W2 AS REQUIRED.
<br />A ACCEPTABLE MANUFACTURERS - GYPSUM PANELS:
<br />3. LOCK EDGE: BEVEL 1/8 INCH IN 2 INCHES.
<br />2. WAGER 5200 MLT i-6 DLY ALM (HANDICAP ACCESS) DOOR CLOSERS
<br />1. CERTAINTEED GYPSUM, INC. (WWW.CERTAINTEED.COM)
<br />E. SAND. ASTM Ct44, GLEAN, FREE OF ORGANIC MATTER
<br />4. DO NOT CUT DOORS DOWN TO OPENING SIZES SMALLER THAN THOSE FOR WHICH
<br />PART 1 GENERAL
<br />3. OFFSET PIVOTS
<br />2. GP GYPSUM CORPORATION. (WWWGP.COM)
<br />F. LIME: ASTM C201, TYPE S, HYDRATED.
<br />THEY WERE MANUFACTURED.
<br />1.1 WORK INCLUDED
<br />4. ADAMS RiTE MS 1850A DEADLOCK
<br />3. NATIONAL GYPSUM CO. (WWWNATIONALGYPSUMCOM)
<br />G. WATER CLEAN, POTABLE.
<br />D. INSTALLATION TOLERANCES:
<br />A. FURNISH ALL LABOR, MATERIAL, SERVICE AND EQUIPMENT NECESSARY TO
<br />5. MANUFACTURER'S STANDARD PUSH/PULL HARDWARE. REFER TO DRAWINGS FOR
<br />4. TEMPLE -INLAND. (WWW.TEMPLEINLAND.COM)
<br />H. GROUT:
<br />I. WARP: MAXIMUM 1/4 INCH IN ANY 3'-0" X 1'-0" PORTION OF DOOR, MEASURED
<br />COMPLETE THE INSTALLATION OF THE DRIVE-THRU WINDOW AS DETAILED ON THE
<br />DOORS WHICH ARE TO BE PREPARED FOR CUSTOM "D" HANDLES. REFER GO
<br />5. USG CORPORATION. (WWW.USG.COM)
<br />1. A1183, EPDXY TYPE.
<br />WITH TAUT STRING OR STRAIGHT EDGE ON CONCAVE FACE OF DOOR
<br />DRAWINGS AND SPECIFIED IN THIS SECTION.
<br />NATIONAL ACCOUNTS FOR ORDERING AND INSTALLATION INFORMATION.
<br />B• ACCEPTABLE MANUFACTURERS - CEMENTITIOUS PANELS:
<br />Z. COLOR AS INDICATED ON DRAWINGS.
<br />6. WAGER 4048 MIL '/2' X 4" THRESHOLD
<br />PART 2 PRODUCTS
<br />B. SET NO. 2 - DOORS FROM TOILETS TO HALL. (SEE DOOR SCHEDULE AND FLOOR
<br />I. USG CORPORATION. (WU1lS .. .OM)
<br />(. JOINT SEALERS: SPECIFIED IN SECTION 01 S200.
<br />2J DRIVE-THRU WINDOW
<br />PLAN FOR QUANTITY, SIZE AND DIRECTION OF SWING)REGULAR
<br />22 MATERIALS - GYPSUM PANELS
<br />J. JOINT TAPE: WATERPROOF, PERFORATED BEDDING TAPE.
<br />SECTION 082113
<br />A SHALL BE AS MANUFACTURED BY:
<br />i. 1-1/2 PAIR BUTTS, HAGER BB-121S 26D
<br />A
<br />GYPSUM BOARD: TM C1396-t 48 ES WIDE X THICKNESS INDICATED,
<br />PLASTIC FACED SOLID CORE METAL CLAD DOOR
<br />1. READY -ACCESS OF WEST CHICAGO, iLLINOIS - SEE NATIONAL ACCOUNT SOURCE
<br />2. 1 LOCK -SET, HAGER 3440 WTN US260
<br />MAXIMUM PRACTICAL LENGTH, TAPERED EDGE.
<br />PART 3 EXECUTION
<br />!!FORMATION FOR ORDERING INFORMATION.
<br />3. 1 FLOOR STOP, HAGER 24F U8260
<br />B. FIRE RESISTANT GYPSUM BOARD: ASTM C13S6, TYPE Xt 48 INCHES WIDE X
<br />PART t GENERAL
<br />THICKNESS INDICATED, MAXIMUM PRACTICAL LENGTH, TAPERED EpGEt APPLY GO
<br />3.1 PREPARATION
<br />12 SUBMITTALS
<br />2.
<br />2. QUICKSERVE OF HOUSTON, TX - SEE NATIONAL ACCOUNT SOURCE INFORMATION
<br />4. 1 KICK PLATE, WAGER 2146 BLACK 10- X 2" L.W.O.D. LOCAL BARRIER FREE CODE
<br />FiRE RATED ASSEMBLIES.
<br />GLEAN SURFACES TO REMOVE LOOSE AND FOREIGN MATTER THAT COULD IMPAIR
<br />A. SUSTAINABLE DESIGN SUBMITTALS:
<br />FOR ORDERING INFO
<br />MAY REQUIRE LARGER KiCK PLATES - VERIFY BEFORE ORDERING.
<br />C. WATER RESISTANT GYPSUM BOARD: ASTM C1396t 48 INCHES WiDE X THICKNESS
<br />ADHESION
<br />1. RECYCLED CONTENT.
<br />B. READY -ACCESS OR QUICKSERVE (FLUSH MOUNT, SiNGLE PARTING), SHALL MEET THE
<br />FOLLOWING CRITERIA:
<br />5. 1 CLOSER, HAGER 5200 MLT i-6 ALM
<br />INDICATED, MAXIMUM PRACTICAL LENGTH, WATER fESISTANTt APPLY TO WALLS TO
<br />B. REMOVE RiDGES PROJECTIONS.FILLSETTINGVOIDSWITH
<br />SND
<br />2. REGIONAL MATERIALS.
<br />1, TOTAL OVERALL DIMENSION FOR DRIVE THRU WINDOW 48 IN. WIDE BY 44 iN. NIGH.
<br />C. SET NO. 3 - DOOR FROM STORAGE TO EXTERIOR METAL DOOR AND FRAME. (SEE
<br />DOOR SCHEDULE AND FLOOR PLAN FOR QUANTITY, SIZE AND DIRECTION OF SWING.)
<br />RECEIVE TILE, SANITARY WALL PANELS AND WALLS At LOCATIONS SPECIFIED ON
<br />DRAWINGS.
<br />PATCHING ND MATERIALS.
<br />(NO TRANSOM)( TOTAL OVERALL DIMENSIONS FOR DRIVE THRUI WINDOW WiTH
<br />i. 3 EA. HiNGES, WAGER 5511SI 320
<br />D. FIRE RESISTANT, WATER RESISTANT GYPSUM BOARD: ASTM C13S6, TYPE Xt 48
<br />C. ALLOWABLE SUBSTRATE TOLERANCES:
<br />PART 2 PRODUCTS
<br />GRANSOME ABOVE 48 IN. WiDE BY 60 IN. HIGH.
<br />2. t LOCKSET, WAGER 34W WitN US26O
<br />INCHES WIDE X3/4THICKNESS INDICATED, MAXIMUM PRACTICAL LENGTH, WATER
<br />i. THIN SET METHOD:
<br />2.1 MANUFACTURERS
<br />2. WINDOW OPENING SIZE IS IN. WIDE BY 35 IN. HIGH.
<br />3. t CLOSER, HAGER 5100 PA 1-6 HDHOS ALM
<br />RESISTANTt APPLY TO WALLS TO RECEIVE TILE, SANITARY WALL PANELS AND
<br />a. MAXIMUM VARIATION IN SUBSTRATE SURFACE: 1/8 INCH IN 8 FEET.
<br />A. ACCEPTABLE MANUFACTURERS:
<br />3. CLEAR ANODIZED ALUMINUM EXTRUSIONS.
<br />4. 1 THRESHOLD, WAGER 413E MiL
<br />WALLS At LOCATIONS SPECIFIED ON DRAWINGS.
<br />b. MAXIMUM HEIGHT OF ABRUPT IRREGULARITIES: 1/32 INCH.
<br />I. ELIASON CORPORATION, KALAMAZOO, MI
<br />4. TRACK FREE BOTTOM SILL PROVIDES FOR A CONTAMINANT SURFACE.
<br />5. I SWEEP, HAGER 8025 B MIL
<br />E. RECYCLED CONTENT: GYPSUM WALLBOARD SHALL CONTAIN RECYCLED CONTENT
<br />2. THICK SET METHOD: MAXIMUM 1/4 INCH IN 10 FEET VARIATION IN SUBSTRATE
<br />22 MATERIALS
<br />5. AUTOMATIC LOCKS EACH TiME THE WINDOW CLOSES,
<br />6. I HOLDER/STOP, WAGER 2688 US260
<br />MATERIAL AS FOLLOWS: PAPER FACINGS: A MINIMUM OF 100`•� POST -CONSUMER
<br />SURFACE
<br />A DOOR BODY
<br />6. SLIDING WINDOW AUTOMATICALLY OPENS HORIZONTALLY WHEN THE SERVER
<br />1. 1 SET W/STRIPPING, WAGER 800E B MIL
<br />RECYCLED PAPER CONTENT. GYPSUM CORES: WHERE FEASIBLE, A MINIMUM OF 10
<br />I. D63" THICK TEMPERED ALUMINUM ALLOY WiTH DELTA FORMED VERTICAL EDGES.
<br />STEPS INTO THE RANGE OF THE WINDOW SCAN CONTROL WINDOW REMAINS OPEN
<br />S. I LOCK GUARD, WAGER 341D 320
<br />POST-INDUSTRIAL RECYCLED GYPSUM CONTENT. THE PERCENTAGE OF RECYCLED
<br />CONTENT IS BASED ON Ti-4E WEIGHT OF THE COMPONENT MATERIALS.
<br />D. TEST CONCRETE SUBSTRATE TO ASTM 04263t DO NOT INSTALL TiLE UNTIL
<br />SURFACES ARE SUFFICIENTLY DRY.
<br />2. RECYCLED CONTENT: MINIMUM PERCENT, WITH MINIMUM PERCENT CLASSIFIED AS
<br />A LONG AS SERVER STAYS IN SCAN BEAM. WINDOW CLOSES ONCE SERVER
<br />STEPS AWAY FROM WINDOW SCAN i5EAM.
<br />9, t DOOR VIEWER HAGER 1156 U626D
<br />23MAGERIALS - CEMENTITIOUS PANELS
<br />32 INSTALLATION
<br />POST -CONSUMER AS SHOWN ON DRAWINGS
<br />23FINISHES
<br />1. WINDOW CAN BE OPENED MANUALLY IF POWER GOES OFF.
<br />10.ALtERNATE DOOR VIEWER MODEL "L-1KsLF-tL1D, 9" X 5", NATIONAL GUARD
<br />A CEMENTIGIOUS PANELS: ANSi A 118.5, HIGH DENSITY, CEMEtNTiTIOUS WiTH GLASS FIBER
<br />A INSTALL CRACK SUPPRESSION MEMBRANE IN ACCORDANCE WITH MANUFACTURER'S
<br />REFER TO DOOR SCHEDULE SHEET.
<br />S. GLASS SHALL BE 1/4 IN. TEMPERED GLASS AS SPECIFIED IN SECTION 08800.
<br />PRODUCTS
<br />REINFORCING, 5/8 INCH THICK X 48 INCHES WIDE, MAXIMUM PRACTICAL LENGTH,
<br />INSTRUCTIONS.
<br />S. INSTALLATION BY LOCAL READY -ACCESS DISTRIBUTOR (OPTIONAL).
<br />ENDS AND EDGES SQUARE CUTt APPLY t0 WALLS IN LOCATIONS AS INDICATED ON
<br />B. METHODS:
<br />PART 3 EXECUTION
<br />10. ONE (1) YEAR WARRANTY ON PARTS AND LABOR
<br />SECTION 088000
<br />DRAWINGS.
<br />2.4ACCRAWIN S.
<br />1. WALLS: ANSI A108b, THIN SET WITH EPDXY ADHESIVE.
<br />3.1 INSTALLATION
<br />11. PREPAID FREIGHT GO JOB SITE.
<br />GLAZING
<br />A FASTENERS: ASTM C1002, TYPE W SCREWS, MINIMUM 5/8 INCH PENETRATION INTO
<br />2. FLOORS: ANSI A1085, THIN SET WITH LATEX-PORTLAND CEMENT MORTAR
<br />A. INSTALL DOORS AND FRAMES IN ACCORDANCE WITH MANUFACTURER'S
<br />MATCH
<br />12. COLOR TO MATCH STOREFRONT
<br />FRAMING•
<br />C. MINIMIZE PIECES LESS THAN ONE HALF SIZE. LOCATE CUTS TO BE INCONSPICUOUS.
<br />SPECIFICATIONS AND AS SHOWN ON THE DRAWINGS.
<br />C. OPTIONAL READY -ACCESS OR QU(GKSERVE - 'PLUSH MOUNT, BI-PARTING AND
<br />PART i GENERAL
<br />B. ADHESIVE:
<br />D. LAY TILE t0 PATTERN SHOWN ON DRAWINGS. DO NOT IN7ERRUP'(' TILE PATTERN
<br />BUMP" - ALSO AVAILABLE FOR SITUATIONS WHERE - "FLUSH MOUNT, SINGLE
<br />iJ SUMMARY
<br />1. TYPE RECOMMENDED BY GYPSUM PANEL MANUFACTURER
<br />THROUGH OPENINGS.
<br />PARTING" - MODEL CANNOT BE USED - SEE NATIONAL ACCOUNT SOURCE
<br />A SECTION INCLUDES:
<br />2. MAXIMUM VOLATILE ORGANIC COMPOUND (VOC) CONTENT: 50 GRAMS PER
<br />E. JOINT WIDTHS:
<br />SECTION 084t13
<br />INFORMATION FOR COMPLETE SPECIFICATIONS.
<br />I. GLASS FOR OTHER SECTIONS REFERENCING THiS SECTION.
<br />LITER
<br />i. CERAMIC TILE: 1/8 NCH, PLUS OR MINUS 1/16 INCH.
<br />ALUMINUM -FRAMED ENTRANCES AND STOREFRONTS
<br />13 SUBMITTALS
<br />C. TRIM ACCESSORIES: ASTM C1041.
<br />D. OPTIONAL QUICKBERVE MODEL ARE AVAILABLE -SEE NATIONAL ACCOUNTS
<br />A SUSTAINABLE DESIGN SUBMITTALS:
<br />1. MATERIAL: FORMED STEEL, MINIMUM 26 GAGE CORE STEEL, HOT DIP GALVANIZED
<br />2. PORCELAIN AND QUARRY TILE: I/4 INCH, PLUS OR MINUS I/8 INGI-I.
<br />PART I GENERAL
<br />1. RECYCLED CONTENT.
<br />FINISH, EXPANDED FLANGES.
<br />F. MAKE JOINTS WATERTIGHT, WITHOUT VOIDS, CRACKS, EXCESS MORTAR, OR EXCESS
<br />1.1 SUMMARY
<br />PART 3 EXECUTION
<br />2. REGIONAL MATERIALS.
<br />2. COFiTLER REINFORCEMENT: GA-2i6, TYPE 05-100 X 100.
<br />GROUT. ALIGN JOINTS IN WALL AND FLOOR OF SAME -SIZED TILE.
<br />A. SECTION INCLUDES:
<br />3.1 INSTALLATION OF DRIVE-THRU WINDOW
<br />3. LOW -EMITTING MATERIALS.
<br />3. CASING: GA-216, TYPE LC.
<br />G. FIT TILE AROUND PROJECTIONS AND AT PERIMETER SMOOTH AND CLEAN CUT
<br />EDGES. ENSURE THAT TRIM WILL COMPLETELY COVER GUT EDGES.
<br />1. ALUMINUM ENTRANCE DOORS AND FRAMES.
<br />2. ALUMINUM FRAMED GLAZED STOREFRONTS.
<br />A. ALUMINUM PLACED IN CONTACT WITH DISSIMILAR MATERIAL, INCLUDING STEEL,
<br />i.4 PROJECT CONDITIONS
<br />4. CONTROL JOINT.
<br />O. JOINT 'TREATMENT MATERIALS:
<br />H. INSTALL TRIM.
<br />CONCRETE, CINDER BLOCK, TILE OR OCHER MASONRY MATERIAL SHALL BE
<br />A. PERFORM GLAZING WHEN AMBIENT TEMPERATURE 1S ABOVE 40 DEGREES F.
<br />3. GLASS ENFiLL PANELS.
<br />BACK -PAINTED WITH AN APPROVED BITUMINOUS PAINT.
<br />B. PERFORM GLAZING ON DRY SURFACES.
<br />ING 1. REINFORCTAPE AND JOINT COMPOUND( ASTM C415.
<br />1. INSIDE CORNERS: COVE UNITS.
<br />4. DOOR HARDWARE.
<br />B. ALL JOINTS (BETWEEN METAL AND MASONRY SHALL BE FULLY CAULKED IN ORDER
<br />2. JOINT COMPOUND( MAXIMUM VOLATILE ORGANIC COMPOUND (VOG) CONTENT:
<br />2. OUTSIDE CORNERS: BEAD UNITS.
<br />13 SYSTEM DESCRIPTION
<br />TO SECURE A WATERTIGHT JOB WITH DYMERIC 511 (MULTI -COMPONENT CHEMICALLY
<br />PART 2 PRODUCTS
<br />250 GRAMS PER LITER
<br />3. BASE: BASE UNITS.
<br />A. DESIGN REQUIREMENTS: DESIGN EXTERIOR SYSTEMS TO WITHSTAND:
<br />CURED POLYURETHANE) AS MANUFACTURED BY 'TREMCO MANUFACTURING
<br />2.1 MANUFACTURERS
<br />4. EXPOSED TILE ENDS: BULLNOSE UNITS.
<br />I. DESIGN WINO PRESSURE iN ACCORDANCE WITH ASCE 1, BUILDING CODE, TESTED
<br />IN ACCORDANCE WITH ASTM E330.
<br />COMPANY, BEECHWOOD, OHEO. APPLY IN STRICT ACCORDANCE WITH
<br />MANUFACTURER'S DIRECTIONS. JOINTS SHALL BE NEATLY POINTED AND EXCESS
<br />A. ACCEPTABLE MANUFACTURERS - GLASS:
<br />PART 3 EXECUTION
<br />3.INSTALLATION PANELS
<br />GLS
<br />I. ALLOW TILE TO SET FOR A MINIMUM OF 48 HOURS BEFORE GROUTING.
<br />2. MOVEMENT CAUSED BY AN AMBIENT TEMPERATURE RANGE OF 120 DEGREES F
<br />SHALL BE REMOVED. SET FILLER PLATES IN CAULKING.
<br />1. PPG INDUSTRIES, INC. (I�1I�uFP1�G AZIN �C0M]
<br />A INSTALLLPANELS AND ACCESSORIES IN ACCORDANCE WITH ASTM C154, GA-2I6,
<br />PE
<br />J. GROUT TILE JOINTS IN ACCORDANCE WITH ANSI A108.10 WITHOUT EXCESS GROUT.
<br />AND A SURFACE TEMPERATURE RANGE OF 160 DEGREES F.
<br />32 PROTECTION AND GLEANING
<br />2. PILKINGTON ARCHITECTURAL. (WWWPILKiNGTON.GOM)
<br />AND MANUFACTURER'S INSTRUCTIONS.
<br />K CONTROL JOINTS-
<br />5. PERFORMANCE REQUIREMENTS:
<br />A. DRIVE-THRI WINDOW SHALL BE PROTECTED DURING CONSTRUCTION AND AFTER
<br />B. ACCURATELY CUT PANELS TO FIG AROUND OPENINGS AND PROJECTIONS. DO NOT
<br />1. PROVIDE CONTROL JOINTS AT:
<br />1. AIR iNFILTRATION, TESTED GO ASTM E283.
<br />INSTALLATION TO PREVENT INJURY AND / OR STAINING. ALL ALUMINUM WORK SHALL
<br />22 MATERIALS - GLASS
<br />TEAR FACE PAPER OR BREAK GYPSUM CORE.
<br />a. CHANGES IN BACKUP MATERIAL.
<br />a. ENTRANCES:
<br />BE THOROUGHLY GLEANED UPON COMPLETION OF THE WORK DO NOT USE
<br />A CLEAR GLASS: ASTM C1036, TYPE 1 TRANSPARENT FLAT, GLASS I CLEAR, QUALITY
<br />C. APPLY PANELS AT NON FIRE -RATED ASSEMBLIES IN MOST ECONOMICAL MANNER
<br />I) SINGLE POOR: MAXIMUM 05 Cif F PER MINUTE PER LINEAR FOOL OF
<br />ABRASIVE CLEANING AGENTS.
<br />Q3 GLAZING SELECT.
<br />WITH ENDS AND EDGES OCCURRING OVER SUPPORTS.
<br />b. CHANGES IN PLANE,
<br />PERIMETER CRACK, AT STATIC PRESSURE DIFFERENTIAL OF 624 PSF.
<br />B. CLEAR TEMPERED GLASS: ASTM C1048, TYPE 1 TRANSPARENT FLAT, GLASS 1
<br />D. APPLY PANELS AT FIRE -RATED ASSEMBLIES AS REQUIRED BY DESIGN ASSEMBLY.
<br />c. OVER JOINTS IN SUBSTRATE.
<br />b. STOREFRONT: 0m6 CIFM PER SQUARE FOOT OF FIXED AREA AT STATIC
<br />CLEAR, QUALITY 03 GLAZING SELECT, KIND FG FULLY TEMPERED.
<br />E. STAGGER JOINTS ON OPPOSITE SIDES OF PARTITIONS,
<br />d. MAXIMUM 24 FEET ON CENTER AT INTERIOR LOCATIONS EXCEPT MAXIMUM 8
<br />PRESSURE DIFFERENTIAL OF 624 PSF.
<br />SECTION 081100
<br />C. RECYCLED CONTENT: MINIMUM PERCENT RECYCLED GLASS CONTENT, CLASSIFIED
<br />F. 00 NOT LOCATE JOINTS TO ALIGN WITH EDGES OF OPENINGS UNLESS A CONTROL
<br />FEET AT SURFACES EXPOSED t0 DIRECT SUNLIGHT.
<br />2. WATER INFILTRATION: NO UNCONTROLLED WATER LEAKAGE, TESTED t0 ASTM E331
<br />DOOR HARDWARE
<br />AS POST-INDUSTRIAL AS SHOWN ON DRAWINGS.
<br />JOINT IS INSTALLED.
<br />Z. FORM JOINTS PER 7CNA METHOD EJ-111,
<br />AT MINIMUM TEST PRESSURE OF 624 PSF FOR INSWING DOORS AND 8.0 PSF FOR
<br />23ACCESSORIES
<br />A SETTING BLOCKS: ASTM C864, NEOPRENE OR EPDM, OR ASTM C1115, SILICONE( 80
<br />G. MECHANICALLY FASTEN SINGLE LAYER PANELS TO FRAMING. PLACE FASTENERS
<br />3. INSTALL JOINT BACKING AND JOINT SEALER AS SPECIFIED IN SECTION 01 S200.
<br />OUTSWING DOORS AND STOREFRONT.
<br />PART i GENERAL
<br />MINIMUM 3/8 INCH FROM EDGES OF PANEL.Si DRIVE HEADS SLIGHTLY BELOW
<br />33ADJUSTING
<br />3. UNIFORM STRUCTURAL LOADING: NO GLASS BREAKAGE OR PERMANENT DAMAGE
<br />1.1 SUMMARY
<br />TO W SHORE A DUROMETER HARDNESS.
<br />SURFACE. STAGGER FASTENERS At ABUTTING EDGES.
<br />TO FASTENERS OR SYSTEM COMPONENTS, TESTED TO ASTM E330 AT I5 TIMES
<br />A SECTION INCLUDES:
<br />B. SPACERS: ASTM C864, NEOPRENE OR EPDM, OR ASTM C1115, SILICONE( 50 TO 60
<br />44. APPLY FACE LAYER OF DOUBLE LAYER APPLICATIONS WiTH JOINTS OFFSET FROM
<br />A REMOVE AND REPLACE PIECES THAT HAVE BEEN DAMAGED DURING INSTALLATION.
<br />DESIGN PRESSURE.
<br />1. HARDWARE FOR STEEL, WOOD, AND ALUMINUM DOORS.
<br />SHORE A DUROMETER HARDNESS.
<br />THOSE IN BASE LAYER( SECURE WITH MECHANICAL FASTENERS TO FRAMING OR
<br />3APROTECTION
<br />4. THERMAL TRANSMITTANCE DUE TO CONDUCTION (UC)- MAXIMUM 0.60, TESTED TO
<br />2. WEATHERSTRIPPING AND THRESHOLDS.
<br />C. GLAZING GASKETS:
<br />WITH ADHESIVE TO BASE LAYER
<br />A PROVIDE PROTECTION FOR COMPLETED U10Fa'IC USING NON -STAINING SHEET
<br />AAMA 1503 ON TWO 6'-0" X 6'-0" UNITS WITH I INCH CLEAR INSULATING GLASS.
<br />FE
<br />3. HARDWARE FOR OTHER SECTIONS RERENCING t4.4fS SECTION.
<br />1. DENSE COMPRESSION GASKETS: ASTM C864, NEOPRENE OR EPDM, OR ASTM C1115,
<br />1. AT DEFLECTION COMPENSATING HEAD TRACKS, CUT PANELS 1/2 INCH SHORT OF
<br />COVERINGS.
<br />5. CONDENSATION RESISTANCE FACTOR (CRFh MINIMUM 50, TESTED GO AAMA 1503.
<br />SILICONE OR THERMOPLASTIC POLYOLEFIN RUBBER MOLDED OR EXTRUDED
<br />STRUCTURE AT HEADt DO NOT SECURE PANELS TO TOP RUNNER CHANNEL.
<br />B. PROHIBIT TRAFFIC ON TiLE FLOORS FOR MINIMUM 3 DAYS AFTER INSTALLATION.
<br />1
<br />PART 2 PRODUCTS
<br />CHANNEL RETAINING SLOTt BLACK COLOR
<br />J. TREAT GUT EDGES AND HOLES IN MOISTURE RESISTANT GYPSUM BOARD WITH JOINT
<br />A. SUBMITTALS FOR REVIEW:
<br />2. SOFT COMPRESSION GASKETS: ASTM C50S, TYPE 11, BLACK, MOLDED OR
<br />SEALER
<br />1. SHOP DRAWINGS: INDICATE SYSTEM DIMENSIONS, FRAMED OPENING
<br />2.1 MANUFACTURERS
<br />EXTRUDED, NEOPRENE, EPOM, SILICONE OR THERMOPLASTIC POLYOLEFIN
<br />K WHERE RECESSED ITEMS OCCUR IN FIRE RATED PARTITIONS, BOX ITEM ON ALL
<br />REQUIREMENTS AND TOLERANCES, TRIM, SEALERS, HARDWARE, AND
<br />A. ACCEPTABLE MANUFACTURERS - BUTT HINGES:
<br />RUBBER OF PROFILE AND HARDNESS REQUIRED TO MAINTAIN WATERTIGHT
<br />SIDES WITH GYPSUM BOARD AS REQUIRED TO MAINTAIN CONTINUITY OF FIRE
<br />SECTION 09 5100
<br />ACCESSORIES.
<br />I. WAGER COMPANIES. (WWW.HAGERCO.COM)
<br />SEAL( BLACK COLOR
<br />RATING.
<br />ACOUSTICAL CEILINGS
<br />B. SUSTAINABLE DESIGN SUBMITTALS:
<br />B. ACCEPTABLE MANUFACTURERS - LOCKSETS, LATCHSETS, DEADBOLTS, AND
<br />2AFABRICATION
<br />32 INSTALLATION OF CEMENTITIOUS PANELS
<br />PART 1 GENERAL
<br />I. RECYCLED CONTENT.
<br />CYLINDERS:
<br />A TEMPERED GLASS:
<br />A INSTALL IN ACCORDANCE WITH ANSI A108.11 AND MANUFACTURER'S INSTRUCTIONS.
<br />1.1 SUMMARY
<br />2. REGIONAL MATERIALS.
<br />i. WAGER COMPANIES. (WWW.HAGERCO.COM)
<br />1. COMPLY WITH ASTM C1048.
<br />B. APPLY PANELS HORIZONTALLY, WITH ENDS OCCURRING OVER SUPPORTS. STAGGER
<br />C. ACCEPTABLE MANUFACTURERS - CLOSERS:
<br />2. PROCESS IN HORIZONTAL POSITION SO THAT INHERENT ROLLER DISTORTION WILL
<br />END JOINTS N ADJACENT ROWS.
<br />A SECTION INCLUDES:
<br />I��!��
<br />I. HAGER COMPANIES. CJ 4A`-ERCOCOM)
<br />"PARALLEL TO BUILDING FLOOR LINES AFTER INSTALLATION.
<br />C. CUT PANELS TO FIG AROUND OPENINGS AND PROJECTIONS.
<br />i. SUSPENDED METAL CEILING GRiD SYSTEM.
<br />PART 2 PRODUCTS
<br />2.1 MANUFACTURERS
<br />D. ACCEPTABLE MANUFACTURERS - DOOR SEALS:
<br />B. SEALED INSULATING GLASS:
<br />D. MECHANICALLY FASTEN PANELS TO FRAMING AT MAXIMUM 12 INCHES ON CENTER
<br />2. ACOUSTICAL PANELS.
<br />A. ACCEPTABLE MANUFACTURERS:
<br />I. HAGER COMPANIES. (WWW.HAGERCO COM
<br />1. COMPLY WITH ASTM E2180.
<br />331NStALLAtiON OF ACCESSORIES
<br />12 SUBMITTALS
<br />i. UNITED STATES ALUMINUM
<br />22 MANUFACTURED UNITS
<br />2. FABRICATE SPACER BAR FRAME OF TUBULAR ALUMINUM FILLED WITH DESICCANT.
<br />A INSTALL IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS.
<br />A SUSTAINABLE DESIGN SUBMITTALS:
<br />A. BUTT }.TINGES:
<br />3. BOND SPACER BAR FRAME TO GLASS PANES WITH TWIN PRIMARY SEALS.
<br />B. INSTALL CORNER REINFORCEMENT AT OUTSIDE CORNERS. USE SINGLE LENGTHS
<br />2. YKK AP AMERICA, INC. (WWW.YKKAPCOM)
<br />i. DESCRIPTION: ANS115WMA A156.1, FULL MORTISE TYPE, FIVE KNUCKLE, NON -RISING
<br />4. FILL SPACE OUTSIDE FRAME TO GLASS EDGE WiTH ELASTOMERIC SEALANT.
<br />WHERE LENGTH OF CORNER DOES NOT EXCEED STANDARD LENGTH.
<br />1, RECYCLED CONTENT.
<br />22 MATERIALS
<br />PIN, HOLE IN BOTTOM TIP FOR PIN REMOVAL.
<br />C. LAMINATED GLASS:
<br />C. INSTALL CASINGS WHERE INDICATED AND WHERE GYPSUM BOARD ABUTS
<br />2. REGIONAL MATERIALS.
<br />A. ALUMINUM:
<br />2. EXTERIOR OUTSWINGING DOOM: PROVIDE SET SCREW IN BARREL MAKING HINGE
<br />1. COMPLY WITH ASTM C1112 AND ANSI ZS1.1•
<br />DISSIMILAR MATERIALS OR STOPS WITH EDGE EXPOSED.
<br />13 PROJECT CONDITIONS
<br />1. EXTRUSIONS: ASTM 5221, 6063-T5 ALLOY AND TEMPER
<br />NON -REMOVABLE WHEN DOOR IS CLOSED.
<br />2. LAMINATE GLASS WITH LAMINATING FILM BY MANUFACTURER'S STANDARD HEAT
<br />D. INSTALL CONTROL JOINTS AT WALLS AND PARTITIONS:
<br />A ENVIRONMENTAL REQUIREMENTS: INSTALL IN APPROXIMATELY SAME CONDITIONS
<br />2. SHEET: ASTM 820S, ALLOY AND TEMPER BEST SUITED TO APPLICATION.
<br />3. WEIGHT: STANDARD WEIGHT.
<br />AND PRESSURE PROCESS.
<br />1. At CHANGES IN BACKUP MATERIAL.
<br />OF TEMPERATURE AND HUMIDITY AS WILL PREVAIL AFTER INSTALLATION.
<br />3. RECYCLED CONTENT: MINIMUM PERCENT, WITH MINIMUM PERCENT CLASSIFIED AS
<br />4. BEARING TYPE: BALL BEARING
<br />3. CUT GLASS TO REQUIRED SIZE At FACTORY.
<br />2. AT MAXIMUM 30 FEET ON CENTER
<br />1.4 MAINTENANCE
<br />POST -CONSUMER AS SHOWN ON DRAWINGS.
<br />23COF'MPONENTS
<br />5. SIZE: 4-1/2 X 4-1/2 INCHES.
<br />4. DISCARD GLASS WITH VOIDS, DELAMINATION, OR ENTRAPPED DIRT OR FOREIGN
<br />3. ABOVE ONE JAMB OF OPENINGS IN PARTITIONS.
<br />A. EXTRA MATERIALS: ONE UNOPENED CARTON OF EACH ACOUSTICAL PANEL.
<br />B. LOCKSETS, LATCHSETS, DEADBOLTS, AND CYLINDERS:
<br />MATTER
<br />3.4JOiNG TREATMENT
<br />A. ENTRANCES DOORS: NARROW STELE CONFIGURATION WITH NOMINAL 2 INCH VERTICAL
<br />1. LOCKSETS AND LATCHSETS:
<br />D. LOW-E COATED GLASS: APPLY LOW -EMISSIVITY COATING TO SCHEDULED GLASS
<br />A. TREAT JOINTS AND FASTENERS IN GYPSUM BOARD iN ACCORDANCE WITH GA-214.
<br />STILES AND TOP RAIL AND 10 INCH BOTTOM RAIL.
<br />a. TYPE: ANSI/BH-4MA A1562, GRADE 1, CYLINDRICAL, KEY -IN -LEVER HANDLES.
<br />SURFACE
<br />B. LEVELS FINISH:
<br />PART 2 PRODUCTS
<br />B. STOREFRONT: FLUSH GLAZING SYSTEM DESIGNED TO RECEIVE 1 INCH GLASS B7
<br />2. DEADBOLTS:
<br />1. SURFACES IN SERVICE AREAS: LEVEL 1 FINISH.
<br />2.1 MANUFACTURERS
<br />MEANS OF ELASTOMERIC GASKETS( 2 INCH FACE WIDTH X 4-1/2 INCH DEPTH,
<br />CENTER GLASS APPLICATION, THERMALLY BROKEN
<br />a. TYPE: ANSI/BI-1MA Ai565, CYLINDRICAL TYPE WiTH i INCH BOLT THROIU.
<br />PART 3 EXECUTION
<br />2. SURFACES TO RECEIVE TILE. LEVEL 2 FINISH.
<br />A ACCEPTABLE MANUFACTURERS - SUSPENSION SYSTEM:
<br />C. DOOR HARDWARE: SPECIFIED iN SECTION 081100.
<br />b. FUNCTIONS: AS SCHEDULED.
<br />3.1 PREPARATION
<br />3. SURFACES GO RECEIVE WALL COVERINGS: LEVEL 4 FINISH.
<br />1. ARMSTRONG WORLD INDUSTRIES. (WWil1ARM6TRONG.COM)
<br />2.4ACCE8SORIES
<br />3. STRIKE PLATES: CURVED LIP, MINIMUM LIP PROJECTION NECESSARY t0
<br />A GLEAN GLAZING RA55ETSA REMOVE LOOSE AND FOREIGN MATTER
<br />4. SURFACES t0 RECEIVE SEMIGLOSS OR GLOSS PAINTS: LEVEL 5 FINISH.
<br />B. ACCEPTABLE MANUFACTURERS - ,ACOUSTICAL UNITS:
<br />A. FASTENERS:
<br />PROTECT DOOR FRAME AND TRIM AND TO CONCEAL EDGES OF STRIKE CUTOUT.
<br />B. REMOVE PROTECTIVE COATINGS ON METAL SURFACES.
<br />1. ARMSTRONG WORLD INDUSTRIES. C
<br />i. SERIES 300 STAINLESS STEEL FOR WET LOCATIONS AND EXPOSED FASTENERS.
<br />4. STRIKE BOXES: STEEL.
<br />5. CYLINDERS: SIX PIN, SOLID BRASS.
<br />C. CLEAN GLASS JUST PRIOR t0 INSTALLATION.
<br />32INSTALLATiON - GENERAL
<br />SECTION 09 3000
<br />C. SUBSTITUTIONS. NOT PERMITTED.
<br />2. STAINLESS COATED STEEL FOR OCHER LOCATIONS.
<br />FLUOFIED
<br />6. KEYS: SOLID BRASS OR NICKEL SILVER
<br />A. INSTALL GLASS IN ACCORDANCE WITH GLASS MANUFACTURER'S INSTRUCTIONS.
<br />TILING
<br />PART I GENERAL
<br />S: IN SECMERTION
<br />B. JOINT SEALERS: SPECIFIED IN SECTION 019200.
<br />1. KEYING:
<br />B. MAINTAIN MANUFACTURER'S RECOMMENDED EDGE AND FACE CLEARANCES
<br />1.1 SUMMARY
<br />G. GLASS AND GLAZING ACCESSORIES: SPECIFIED IN SECTION 08 8000.
<br />D. WEATHERSTRIPPING: REPLACEABLE, NONPOROUS SYNG44ETIC WOOL PILE TYPE.
<br />a. CONSTRUCTION KEY LOCKS.
<br />BETWEEN GLASS AND FRAME MEMBERS.
<br />A. SECTION INCLUDES:
<br />(CONTINUED ON NEXT SHEET)
<br />25FABRICAtiON
<br />b. KEY ALIKE, CROSS KEY, OR OTHERWISE KEY AS DIRECTED BY OWNER
<br />331NSTALLATION - GASKET GLAZING METHOD
<br />I. CERAMIC, PORCELAIN AND QUARRY TILE FLOOR AND WALL FINISHES.
<br />A. FABRICATE WITH MINIMAL CLEARANCES AND SHIM SPACES AROUND PERIMETER
<br />c. PROVIDE FOUR KEYS FOR EACH LOCK
<br />A FABRICATE GASKETS TO FIT OPENINGS( ALLOW FOR STRETCHING OF GASKETS
<br />DURING INSTALLATION.
<br />12 QUALITY ASSURANCE
<br />B. ACCURATELY FIT AND SECURE JOINTS AND INTERSECTIONS. MAKE JOINTS FLUSH,
<br />d. INSCRIBE KEYS WITH LOCK MANUFAC'tUtiER
<br />B. SET SOFT COMPRESSION GASKET AGAINST FIXED STOP OR FRAME WITH BONDED
<br />A INSTALLER QUALIFICATIONS: MINIMUM 10 YEARS' EXPERIENCE IN WORK OF THIS
<br />HAIRLINE, AND WEATWERTIGHT.
<br />C. CLOSERS:
<br />MITER CUT JOINTS AT CORNERS.
<br />SECTION.
<br />C. FABRICATE IN LARGEST PRACTICAL UNITS.
<br />1. DESCRIPTION: ANS115HMA AI56.4, OVERHEAD EXPOSED, FIELD ADJUSTABLE TO
<br />DOOR CONDITIONS.
<br />C. SET GLASS CENTERED IN OPENINGS ON SETTING BLOCKS.
<br />B. TILE AND TRIM UNITS: MEET ANSI A131.1, STANDARD GRADE.
<br />D. CONCEAL FASTENERS AND ATTACHMEiNTS FROM VIEW.
<br />2. CONSTRUCTION: CAST ALUMINUM BODY, RACK AND PINION OPERATION WITH
<br />D. INSTALL REMOVABLE STOPS AND INSERT DENSE COMPRESSION GASKETS AT
<br />C. STATIC COEFFICIENT OF FRICTION FOR FLOOR TILE: MINIMUM 0b0, TESTED TO ASTM
<br />E. FABRICATE ALUMINUM COMPONENTS WITH INTEGRAL LOW CONDUCTANCE THERMAL
<br />COMPRESSION SPRING, FULLY HYDRAULIC.
<br />CORNERS, WORKING TOWARD CENTERS OF GLASS, COMPRESSING GLASS AGAINST
<br />C1028 IN DRY CONDITION.
<br />BARRIER LOCATED BETWEEN EXTERIOR AND INTERIOR EXPOSED COMPONENTS
<br />SOFT COMPRESSION GASKETS TO PRODUCE WEATHERTIGHT SEAL,
<br />THAT ELIMINATES METAL -TO -METAL CONTACT.
<br />3. CLOSING AND LATCHING SPEEDS AND BACKGHECK: CONTROLLED BY
<br />E. SEAL JOINTS IN GASKETS.
<br />F DOORS:
<br />INDEPENDENTLY ADJUSTABLE CONGEALED VALVES.
<br />13 DELIVERY, STORAGE AND HANDLING
<br />i. MECHANICALLY FASTENED AND WELDED CORNER CONSTRUCTION.
<br />4. MOUNTING: SURFACE MOUNTED, NON -HANDED WITH UNIVERSAL REGULAR OR
<br />F. ALLOW GASKETS t0 PROTRUDE PAST FACE OF GLAZING SLOPS.
<br />A DELIVER MORTAR ADHESIVE, AND GROUT CONTAINERS BEARING HALLMARK
<br />2. FABRICATE STILES AND RAILS OF MINIMUM 0.188 INCH THICK EXTRUSIONS AND
<br />PARALLEL ARM. SUITABLE FOR MOUNTING ON 1-3/4 INCH MINIMUM DOOR TOP
<br />RAIL OR TRANSOM BAR WITHOUT DROP PLATE.
<br />RAIL
<br />3.4PROTEGTION
<br />CERTIFYING COMPLIANCE WITH REFERENCE STANDARDS.
<br />GLASS STOPS FROM MINIMUM OD50 INCH THICK EXTRUSIONS.
<br />ADJUSTABLE OPENING FORGE AND DELAYED CLOSING IN ACCORDANCE WITH
<br />OPENINGILITY
<br />AFTE
<br />A. AFTER INSTALLATION, MARK GLASS WITH AN 'X' USING REMOVABLE PLASTIC TAPE.
<br />B. PROTECT ADHESIVE CONTAINERS FROM FREEZING AND OVERHEATING ACCORDING
<br />TO MANUFACTURER'S INSTRUCTIONS.
<br />3. PROVIDE WEATHERSTRIPPING At DOOR HEAD, JAMBS, MEETING STILES, AND
<br />APPLICABLE CODE.
<br />35A LE
<br />SILLS.
<br />p, DOOR STOPS: FLOOR MOUNTED, ALUMINUM HOUSING WITH RESILIENT BUMPER
<br />A ALL SALES AREA PRIMARY GLASS - i IN. INSULATING GLASS, 1/2 IN. AIR SPACE WITH
<br />1.4 PROJECT CONDITIONS
<br />4. PREPARE WITH INTERNAL REINFORCEMENTS FOR DOOR HARDWARE.
<br />E KICK PLATES:
<br />1/4 IN. CLEAR POLISHED PLATE FOR OUTDOOR AND INDOOR LIGHTS.
<br />A ENVIRONMENTAL REQUIREMENTS: MAINTAIN MINIMUM AMBIENT TEMPERATURE OF 50
<br />26 FINISHES
<br />1. TYPE; .125 INCH PLASTIC LAMINATE, BEVELED EDGES, SECURED WITH FLATHEAD
<br />B. ALL DRIVE-tHRI GLAZING - '/4 IN. LOW-E GLASS, '/z IN. AiR SPACE WITH '/4 IN. CLEAR
<br />F DURING
<br />DEGREES F DURING AND AFTER INSTALLATION
<br />DEGREES
<br />A. ALUMINUM: AAMA roll, ARCHITECTURAL CLASS I ANODIZED TO 00001 INCH MINIMUM
<br />COUNTERSUNK SCREWS
<br />FLOAT GLASS FOR OUTBOARD LIGHT.
<br />15 MAINTENANCE
<br />THICKNESS, ALUMINUM ANODIZED FINISH.
<br />Z. SIZE: 8 INCHES HIGH X DOOR WIDTH LESS 2 INCHES.
<br />C. ENTRANCE DOORS - 1 IN. INSULATED AND TEMPERED GLASS.
<br />A EXTRA MATERIALS: 2 PERCENT OF EACH TILE.
<br />F. FLUSH BOLTS: MANUAL TYPE, 12 INCHES LONG, WITH DUSTPROOF STRIKE.
<br />D. PROVIDE TEMPERED OR SAFETY GLASS FOR INDOOR AND OUTDOOR GLASS
<br />PART 3 EXECUTION
<br />23FINiSHES
<br />AREAS WHERE REQUIRED BY BUILDING CODES.
<br />PART 2 PRODUCTS
<br />3.1 INSTALLATION
<br />A. FINISHES: TO ANSI/BHMA AI56.18.
<br />E. INSULATING GLASS UNITS SHALL PROVIDE A MIN. U-VALUE OF AS WINTER AND 56
<br />2.1 MANUFACTURERS
<br />A. INSTALL IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS AND APPROVED
<br />B. DOOR CLOSERS: FINISH NO. 689, SILVER ENAMEL.
<br />SUMMER AND SHALL COMPLY WITH ALL REQUIREMENTS OF THE LOCAL GOVERNING
<br />SHOP DRAWINGS
<br />C. THRESHOLDS AND DOOR SEAL HOUSINGS: CLEAR ANODIZED.
<br />ENERGY CODE.
<br />A ACCEPTABLE MANUFACTURERS - TILE:
<br />B. INSTALL COMPONENTS PLUMB AND LEVEL, IN PROPER PLANE, FREE FROM WARP
<br />O. OTHER FINISH NO. 626, SATIN CHROME PLATED.
<br />1. DAL -TILE CORP. (U=ALTILEPRODUGTS.COM)
<br />AND TWIST
<br />SECTION 092900
<br />2. CREATIVE MATERIALS CORP.CHttPS://tLAUllGI�At(VEMAtERIALSCORPCOM/)
<br />C. ANCHOR TO SUPPORTING CONSTRUCTION
<br />GYPSUM BOARD
<br />O. SET THRESHOLDS AND SILL MEMBERS EXPOSED TO WEATHER IN MASTIC AND
<br />PART 3 EXECUTION
<br />B. ACCEPTABLE MANUFACTURERS - SETTING AND GROUTING MATERIALS:
<br />SECURE.
<br />3.1 INSTALLATION
<br />PART I GENERAL
<br />t. MAPEI
<br />E. INSTALL HARDWARE USING TEMPLATES PROVIDED BY MANUFACTURER
<br />A. INSTALL HARDWARE IN ACCORDANCE WITH APPROVED HARDWARE SCHEDULE AND
<br />1.1 SUMMARY
<br />(HTTP://UrNMAPEI.GOMNS-ENlrILE-4-STONE-INSTALLATION-SYSTEMS/GENET((
<br />F. INSTALL GLASS AND ACCESSORIES IN ACCORDANCE WITH SECTION 08 8000.
<br />MANUFACTURER'S INSTRUCTIONS.
<br />A SECTION INCLUDES:
<br />-GROUTS/KERACOLOR-5 )
<br />G. INSTALLATION TOLERANCES:
<br />B. INSTALL MORTISE ITEMS FLUSH WITH ADJACENT SURFACES.
<br />1. GYPSUM BOARD.
<br />G. SUBSTITUTIONS: NOT PERMITTED.
<br />1. MAXIMUM VARIATION FROM PLUMB OR LEVEL: i/8 INCH IN 3 FEET OR 1/4 INCH IN
<br />C. INSTALL LOCKSETS, CLOSERS, AND TRIM AFTER FINISH PAINTING.
<br />2. CEMENTITIOUS PANELS.
<br />22 MATERIALS
<br />mo
<br />REVEM
<br />BY
<br />to
<br />U � CO
<br />M Y to
<br />:a
<br />0 o
<br />CO U
<br />= N
<br />vi
<br />CC I X u
<br />♦ G N
<br />C' s
<br />O � • L
<br />O U • N
<br />Q E
<br />QW 00o
<br />Y ' 3
<br />CO 3
<br />O C ti
<br />A C C
<br />_ o
<br />(u d a
<br />o
<br />tl
<br />I
<br />0
<br />• 1�
<br />O: co
<br />�' Ov CO : Q
<br />LL.W
<br />0'• o ¢ ��
<br />. �IPA
<br />S,
<br />Q
<br />> a o
<br />U.
<br />O o
<br />r
<br />4
<br />0.
<br />O
<br />L
<br />O
<br />.0
<br />> O
<br />C w y
<br />.
<br />s O • w
<br />Cr. Y m c
<br />Z - r
<br />•0 = m U
<br />Ca
<br />} � N
<br />N 0
<br />Vj
<br />O tl
<br />C
<br />Date: 07. 26. 22
<br />Scale: AS NOTED
<br />Project Mgr. JDR
<br />Drawn: JDR
<br />Job: 21-202
<br />Sheet
<br />N5
<br />
|