|
FLOOR PLAN CONSTRUCTION NOTES WALL LEGEND
<br />100 ENERAL CONTRACTOR SHALL VERIFY THE CONDITION OF ALL EXTERIOR / DEMISING WALL, REPLACE STUDS AND DRYWALL AS REQUIRED.
<br />1
<br />101 GENERAL CONTRACTOR SHALL PROVIDE F.R.T. FOR ALL WALL -ATTACHED EQUIPMENT OR AS NORMALLY REQUIRED. ALL BLOCKING TO BE 3/4" F.R.T. PLYWOOD (MARINE GRADE IN WET AREAS). SCREW = EXISTING DEMISING WALL, 6" METAL STUDS @ 16" O.C. WITH
<br />FASTEN BETWEEN METAL STUDS AT NEW PARTITIONS AND FURRED WALLS. AT DEMISING WALLS, APPLY F.R.T. BLOCKING OVER 5/8" TYPE'X' GYPSUM BD. COVER W/ 5/8" GYP BD. AND FINISH WITH F.R.P. 5/8" TYPE'X' GYP. BD, ON BOTH SIDES.
<br />TILE. SECURE TO DEMISING WALL METAL STUDS. SEE BLOCKING DETAILS ON SHEET A1.1. EXISTING F.R.T. AT EXTERIOR WALLS TO BE VERIFIED BY GC.
<br />102 EXISTING ADA COMPLIANCE RESTROOM FIXTURES AND ACCESSORIES TO REMAIN, SEE ENLARGED RESTROOM PLAN. 2
<br />= EXISTING PARTITION WITH 3-5/8" METAL STUDS @ 16" O.C.
<br />103 ENERAL CONTRACTOR SHALL VERIFY THE CONDITION OF ALL EXISTING INTERIOR WALLS, REPLACE ANY DAMAGED GYP. BD. AND STUDS AS REQUIRED.
<br />103A ENERAL CONTRACTOR SHALL FUR OUT WALL TO FLUSH WITH ADJACENT FUR OUT. 3
<br />_ 3-5/8" METAL STUDS @ 16" O.C. TO 6" ABV. FINISHED CLG.-1/A3.0
<br />104 NEW DINING ROOM TABLES AND CHAIRS. COORDINATE WITH OWNER. SEE ELEVATIONS FOR HEIGHT
<br />105 INSTALL NEW WALL TILE AND BASE, WALL TILE IN ROOMS WITH GYPSUM WALLBOARD WALLS SHALL BE THIN SET WITH ADHESIVE IN ACCORDANCE WITH THE TILE COUNCIL OF AMERICA, INC. ANSI A001.008.5.
<br />NOTE: ALL WALL AND SOFFIT TILE SUPPLIED AND INSTALLED BY GENERAL CONTRACTOR. 4
<br />106 VERIFY CONDITION OF EXISTING FRP ON ALL KITCHEN WALLS, IF REQUIRED GENERAL CONTRACTOR SHALL PROVIDE & INSTALL F.R.P. ACCORDING TO THE MANUFACTURERS INSTRUCTIONS FOR APPLICATION = OVER GYPSUM DRYWALL. 4" WALK-IN COOLER/FREEZER INSULATED WALLS. EXISTING TO REMAIN.
<br />107 GENERAL CONTRACTOR SHALL PROVIDE AND INSTALL STAINLESS STEEL PANELS OVER GYPSUM WALL BOARD FROM TOP OF QUARRY TILE BASE TO BOTTOM OF NEW HOOD AND ALONG THE LENGTH OF THE
<br />NEW HOOD. 5
<br />108 GENERAL CONTRACTOR SHALL INSTALL 1-112" X 1-1/2" 16ga.S/S CORNER GUARDS OR END CAPS FROM FLOOR TO CEILING AT ALL OUTSIDE CORNERS WITHIN THE PREP. ROOM. SCREW FASTEN AND SEAL WITH = 6" METAL STUDS @ 16" O.C. TO 6" ABV. FINISHED CLG.-1/A3.0
<br />CLEAR SILICONE, TYP., AT ALL OUTSIDE CORNERS. SEE DETAIL 6/A1.1 SEE ELEVATIONS FOR HEIGHT
<br />109 PROVIDE AND INSTALL SEALED/ POLISHED CONCRETE FLOOR FINISH, SEE FINISH SCHEDULE. 6
<br />110 EXISTING QUARRY TILE FLOOR FINISH QT-1 TO REMAIN, PRESSURE WASH, RE GROUT AND RESTORE TO LIKE NEW CONDITION.
<br />= EXISTING EXTERIOR WALL TO REMAIN
<br />111 OUNTER CUT OUT DIMENSION TO BE VERIFIED WITH EQUIPMENT SUPPLIER
<br />112 EXISTING STOREFRONT GLAZING SYSTEM TO REMAIN. RESTORE TO LIKE NEW CONDITION.
<br />113 ENERAL CONTRACTOR SHALL COORDINATE WITH OWNER AND EQUIPMENT SUPPLIER AND INSTALL NEW CASEWORK SEE SECTIONS ON SHEET #A3.0 INSTALL ALL FINISHES AS SPECIFIED. ALL JOINTS IN AND
<br />AROUND CABINETS, SINKS, VENTILATOR, ICE BIN, ETC., TO BE SEALED WITH CLEAR SILICONE SEALANT. PROVIDE BLACK PLASTIC WIRE WAY GROMMETS AT ALL DRILLED OPENINGS.
<br />114 NEW LOW WALL PARTITIONS. GENERAL CONTRACTOR SHALL PROVIDE AND INSTALL AT 12" O.C. & 3-5/8" METAL STUD PART. WITH 5/8" WATER RESISTANT CEMENT BOARD ON BOTH SIDES.
<br />WALMART NOTES
<br />1. TENANT SHALL REPLACE ANY BASE
<br />MATERIAL AND COMPACT TO MATCH
<br />EXISTING. MATCH FLOOR SLAB THICKNESS
<br />AND FINISH WITH 3,000 PSI CONCRETE.
<br />2. TENANT SHALL FIRST DO TEST DEMOLITION
<br />OF SLAB OF NO MORE THAN 5SF TO
<br />CONFIRM THAT THE EXISTING SLAB
<br />CONDITION IS NOT A STRUCTURAL SLAB. IF
<br />THE EXISTING SLAB CONDITION IS A
<br />STRUCTURAL SLAB TENANT SHALL
<br />IMMEDIATELY STOP UNDERSLAB WORK AND
<br />PROVIDE SLAB
<br />PENETRATION/REMEDIATION DRAWINGS TO
<br />WALMART BY A LICENSED STRUCTURAL
<br />ENGINEER, LICENSED IN THE STATE IN
<br />WHICH THE TENANT WORK IS TAKING
<br />PLACE.
<br />3. NO ROOF STRUCTURAL MEMBERS SHALL
<br />BE REMOVED OR DAMAGED DURING THE
<br />TENANT SPACE DEMOLITION.
<br />4. UNUSED EXISTING LINES AND CAPPED
<br />LINES SHALL BE DONE IN A REVERSIBLE
<br />FASHION.
<br />5. ALL REQUIRED WORK OUTSIDE OF TENANT
<br />SPACE TO BE COORDINATED WITH
<br />WALMART AND ADJACENT TENANTS
<br />BEFORE COMMENCING
<br />DOORSCHEDULE IF EXISTING, ADD HARDWARE AS REQUIRED
<br />JAMB JAMB HARDWARE
<br />MARK DESCRIPTION I TYPE FINISH I JAMB I FINISH I DETAIL
<br />01
<br />EXISTING BACK EXIT DOOR
<br />A
<br />GRAY SEMI
<br />STEEL
<br />3 STANLEY HINGES: FBB179, 4-1/2"x4-112" NRP, 26D
<br />3'-0"x T-0" H.M. DOOR U.L. LABEL "B"
<br />GLOSS
<br />U.L. LABEL "B"
<br />P-1
<br />1 SCHLAGE LOCK, ND80PD RHODES, 626
<br />1 NORTON CLOSER, P83016F SNB ALUM.
<br />RELOCATE DOOR PER FLOOR PLAN LOCATION
<br />P-1
<br />1
<br />1 KICK PLATE, 32"X12" 1 IVES VIEWER, 6981326D
<br />A1.0
<br />1 STOP AS REQUIRED 3 SILENCERS,
<br />I
<br />1 PANIC BAR @ 44" A.F.F.
<br />1 THRESHOLD'PEMKO' #2005 A'T'
<br />1 WEATHER GASKET
<br />1 DOOR SWEEP
<br />02
<br />EXISTING
<br />3'-0" X 7-0" HOLLOW METAL DOOR.
<br />B
<br />GRAY SEMI
<br />ALUMINUM
<br />P-1
<br />3 STANLEY HINGES: FBB179, 4-1/2" X 4-1/2" NRP, 26D
<br />KITCHEN DOOR
<br />GLOSS
<br />2
<br />1 NORTON CLOSER, P83016F SNB ALUM.
<br />P-1
<br />A1.0
<br />1 KICK PLATE, 12"X2" LDW, 32D
<br />1 STOP AS REQUIRED
<br />03
<br />NEW
<br />EX GRILLE CURTAIN
<br />DYNAMIC CLOSER EZ GRILLE
<br />POCKET CONTAINED IN 6" MTL STUD WALL
<br />SECURITY GATE
<br />ALUMINUM
<br />MANUAL PUSH/PULL, PROVIDE PULL STRAPS
<br />OVERHEAD TRACK
<br />CURTAIN CARRIERS
<br />LOCKING POST
<br />GRAY SEMI
<br />GLOSS PAINT
<br />P-1
<br />E:]; S.S. KICK
<br />PLATES DINING
<br />SIDE ONLY
<br />TYPE B
<br />HOLLOW METAL
<br />:IAM91
<br />Scale: 3" = V-0"
<br />SEE ELEVATION
<br />FOR FINISHES
<br />HOLLOW METAL
<br />FRAME, W/ THREE
<br />JAMB ANCHORS
<br />PER JAMB.
<br />SEE DOOR SCHEDULE
<br />JAMB DETAIL A
<br />ELEVATION
<br />=1NISHES
<br />ING DEMISING WALL
<br />o \- PANIC
<br />to DEVICE AS EXISTING HOLLOW METAL'B' LABEL
<br />REQUIRED
<br />TYPE A
<br />HOLLOW METAL
<br />H LEAD / JAM B
<br />Scale: 3" = V-0"
<br />FRAME. WI THREE JAMB ANCHORS
<br />PER JAMB.
<br />EXISTING 1 3/4" H.M.'B' LABEL DOOR. PAINT GRAY
<br />SEMIGLOSS (BOTH SIDES AND EDGES)
<br />DETAIL B
<br />EXIST.
<br />01
<br />2
<br />4
<br />0
<br />HALL
<br />A )108
<br />4'-1"
<br />100
<br />1
<br />8--4-
<br />14'-8"
<br />EXISTING
<br />FREEZER
<br />M
<br />0
<br />M
<br />POLISHED CONCRETE
<br />DINING
<br />104 109
<br />CASEWORK BY
<br />FABRICATOR.
<br />INSTALLED BY GC
<br />0
<br />M
<br />L 2'-0"
<br />6
<br />A4.0
<br />7'-5"
<br />Constructi
<br />SCALE: 1/4" =1'-0"
<br />61-6"
<br />M
<br />15'-4"
<br />5'-4"
<br />101
<br />106
<br />4
<br />100
<br />1
<br />M
<br />EXISTING
<br />WAREWASHING
<br />60
<br />COOLER
<br />110 113
<br />106
<br />108
<br />B
<br />103
<br />T
<br />103
<br />2
<br />106
<br />B 108
<br />106
<br />2
<br />M
<br />ti
<br />EXIST.
<br />A 108
<br />B 108
<br />ih
<br />02
<br />103
<br />106
<br />4'-4"
<br />3'-5"
<br />2'-6"
<br />19'-8"
<br />10'-3"
<br />W
<br />101
<br />103 106
<br />106
<br />LINE OF NEW HOOD ABOVE
<br />GAME ROOM
<br />i
<br />i
<br />i
<br />i
<br />i
<br />00 �
<br />i
<br />co T - 6"
<br />N
<br />i
<br />i
<br />i
<br />i
<br />i
<br />107 i COOKLINE M
<br />110 113
<br />BEVERAGE STATION 6
<br />A4.0
<br />i
<br />i
<br />CV �
<br />i
<br />i
<br />i
<br />i
<br />i
<br />J
<br />TT-
<br />9" 2'-6" 105
<br />A 108 1
<br />108 C
<br />EXISTING QUARRY TILE
<br />3 105 TO REMAIN, GC TO PATCH
<br />AND REPLACE AS NEEDED
<br />COUNTER 100
<br />B 108
<br />3
<br />A3.0
<br />113 111
<br />(- �
<br />114 L — -1
<br />C 1 108
<br />CASEWORK BY
<br />FABRICATOR.
<br />INSTALLED BY GC —
<br />100
<br />o FCV
<br />GC TO INSTALL DYNAMIC CLOSER EZ
<br />GRILLE WITHIN 6" MTL. STUD WALL W/
<br />POCKET - SEE MANUFACTURER'S
<br />SPECIFICATION BEFORE BUILDING
<br />POCKET, MATCH AND ALIGN FINISHES
<br />WITH ADJACENT WALLS
<br />-8" 14'-2"
<br />15' -10"
<br />GC TO VERIFY DIMENSIONS
<br />OF POCKET WALL WITH
<br />MANUFACTURER'S
<br />SPECIFICATIONS
<br />to
<br />r
<br />StudioRG...,
<br />MAIN OFFICE:
<br />1 HUNTINGTON QUADRANGLE
<br />SUITE 2CO3
<br />MELVILLE, NY 11747
<br />P:631.226-7700 F:631.226.7175
<br />® Copyright 2018: RGBK, INC.
<br />Seal:
<br />Landry
<br />GREG LANDRY
<br />ARCHREC11M BANNING INTOMR
<br />1202 Richardson Dr. #106 Tel: 214.631.6941
<br />Richardson, Texas 75080 Fax: 214.634.1814
<br />Gregory
<br />p F F...R
<br />P. •' Y G. �'
<br />. ; Lan ry
<br />AR95731 j
<br />Digi
<br />by regory G
<br />nd ry
<br />G11121 Date:2021.06.01
<br />Architects. Cert. No. AR95731 11:41:31-05'00'
<br />Expiration Date: 2.28.23
<br />Owner:
<br />Charley's Steakery Inc.
<br />ATTN: Amgad Attalla
<br />2952 Carrickton Cir.
<br />Orlando, FL 32824
<br />(201) 668-6672
<br />It is the responsibility of the Construction
<br />Manager/General Contractor and all
<br />Sub -Contractors to verify all dimensions and
<br />accept conditions of prior work by related
<br />trades before proceeding with any work.
<br />Date
<br />07-22-2020
<br />Drawn By Check By
<br />MRP TN
<br />Scale
<br />AS SHOWN
<br />Issued:
<br />Project Title
<br />Charleys
<br />Zephyrhills, FL
<br />WM706
<br />Project Address
<br />7631 Gall Blvd,
<br />Zephyrhills, FL 33541
<br />Project Number
<br />WM706
<br />Drawing Title and Number
<br />FLOOR PLAN AND NOTES
<br />A1.0
<br />
|