Laserfiche WebLink
kmm Date <br />09-0" <br />(D 1-1/2" HANGER STRAPS; MAX. 10' SPACING <br />0 ROUND SNAPLOCK DUCT WITH WRAP INSULATION <br />(D <br />TAKE -OFF OR SPIN -IN FITTING W/ VOLUME DAMPER. <br />(DON'T USE VOLUME <br />DAMPER ABOVE GYP CEILINGS) <br />(D <br />PROVIDE PLASTIC ELBOW STRAIGHTENER TO ELIMINATE KINKS <br />AT ELBOWS FLEXIBLE <br />DUCT - PROVIDE FLEXFLOW, OR EQUAL. <br />METAL COLLAR WITH <br />BAND CLAMP, SCREWED (3) PLACES <br />AND TAPED TYPICAL <br />BOTH ENDS OF FLEX DUCT. <br />INSULATED FLEXIBLE <br />DUCT, MAXIMUM 6' LENGTH. <br />INSTALL FLEX -DUCT <br />AS STRAIGHT AS POSSIBLE. <br />NO BEND OVER 90% <br />NO CRUSHING OF FLEX -DUCT. <br />0 2" WRAP INSULATION OVER BACK OF DIFFUSER <br />SUPPLY DUCT AND DIFFUSER RUN -OUT DETAIL <br />SCALE: NONE <br />1/2"x22 GA. WIDE BAND CLAMP <br />1-1/2"x22 GA. WIDE 1-1/2" x 22 GA. <br />BAND CLAMP SADDLE <br />HANGER AND SUPPORT FOR ROUND AND FLEXIBLE DUCTS <br />NO SCALE <br />0.25 D <br />FANGULAR DUCT <br />>1 <br />n <br />D <br />n <br />D <br />cn <br />BUTTERFLY TYPE <br />DAMPER IN CONICAL <br />SPIN COLLAR WITH <br />QUADRANT. PROVIDE <br />DAMPER AT ALL <br />BRANCH TAKE -OFFS. <br />< <br />ROUND DUCT <br />BRANCH DUCT DETAIL <br />NOT TO SCALE <br />12—GAUGE HANGER WIRE <br />(TYPICAL) <br />I / Z111- <br />E <br />TTOTAAIL HAN =GE�R����. ll-::� <br />EXTENSION = 3" <br />E, <br />MAXIMUM HANGER <br />SPACING <br />8-FT <br />UNISTRUT OR <br />3"X2" CHANNEL <br />(TYPICAL) <br />3" <br />HANGER AND SUPPORT FOR FIBROUS GLASS DUCTS <br />NO SCALE <br />BACKDRAFT DAMPER <br />(INTEGRAL TO CAP) <br />OUTSIDE AIR DUCT ----- <br />SEE PLANS FOR SIZE/ROUTING <br />SEAL WALL OPENING <br />WEATHERTIGHT WITH CAULKING <br />EXTERIOR WALL <br />WALL CAP WITH WEATHERHOOD <br />& INTEGRAL BIRD SCREEN <br />MFG = BROAN # 613 <br />(ALL ALUMINUM CONSTRUCTION) <br />MOUNT TO WALL WITH <br />#10 TECK SCREWS <br />EXHAUST AIR WALL CAP DETAIL <br />SCALE: NONE <br />1/4X20 TPI "ALL THREAD" SUPPLIED BY MC. <br />__ CEILING EXHAUST FAN <br />1114, /,/-- BACKDRAFT DAMPER <br />EXHAUST DUCT SEE PLANS <br />FOR SIZE AND ROUTE <br />CEILING FAN DETAIL <br />SCALE: NONE <br />THOMPSON METAL, OR EQUAL <br />GALVANIZED METAL GOOSENECK <br />ANCHOR CAP TO ROOF <br />W/ #10 TECK SCREWS ON <br />12" CENTERS — ALL SIDES <br />AIR INTAKE <br />FOP <br />FRESH AIR ROOF CAP DETAIL <br />SCALE: NONE <br />CONDENSING UNIT <br />, CUTD" BY MIAMI TECH OR <br />EQUAL. FLORIDA PRODUCT <br />1-1/2" APPROVAL #19731.1—R2 <br />00 0 4"xl-1/2"xl4GA CLIP <br />(4) #10 SS-410 TEK SCREWS <br />TO CASING <br />0 (1) 1/4" x 1-3/4" LONG TAP —CON <br />0 0 CONCRETE ANCHORS OR EQUAL TO <br />CONCRETE PAD OR <br />L (2) #14 SS TEK SCREWS TO RAIL <br />CONCRETE PAD 1 /2" NEOPRENE PAD UNDER EACH CLIP <br />OR ROOFSTAND <br />HEAT PUMP CONDENSER TIE -DOWN DETAIL <br />SCALE: NONE PROVIDE (1) TIE -DOWN CLIP PER CORNER ON EACH <br />SIDE OF UNIT (2 PER SIDE, AND 8 PER UNIT) <br />SLOPED TOP TO SHED RAIN <br />INSULATED PIPING <br />TO U N ITS <br />ANCHOR FLANGED <br />SIDES TO WALL <br />AT 18" INTERVALS <br />AND SILICONE CAI <br />ALL EDGES AT WA <br />22—GAUGE GALV. <br />SHEET METAL. <br />FOAM SEAL BOTTOM <br />PIPING TO UNITS-/ AFTER INSTALLATION TO <br />PREVENT BIRDS AND <br />INSECTS NESTS. <br />REFRIG. PIPING WALL COVER DETAIL <br />SCALE: NONE <br />STEPANEK-L <br />ANDASSOCIATES <br />)2,257 TWELVE OAKS WAY, SUITE 103 <br />WESLEY CHAPEL, FL 33544 <br />PH (813) 991-1248 <br />REGISTRY # 8397 21-143 <br />co LO <br />_(0 <br />co <br />o M <br />< u- <br />z <br />z <br />E <br />M <br />00 <br />I <br />_J ;0 <br />cy) � cl) <br />CD <br />(D 0) <br />Q) <br />-0 <br />0 <br />Job Nwiber <br />Rovkikxw <br />%%011111111111'r /.*, <br />\N D <br />EN <br />No 56189 <br />13 - <br />STATE 0 F <br />0 R <br />,4, <br />/ONA <br />1.41,111111 1 <br />Sh"t No. <br />M2 <br />MATTHEW D. LEWIS, P.E. FL LIC#56189 <br />