38444 5th Ave - Laserfiche WebLink

Browse Search

HVAC GENERAL NOTES 1. ALL WORK SHALL COMPLY WITH APPLICABLE NATIONAL, STATE AND LOCAL CODES. THIS INCLUDES THE 2010 FLORIDA BUILDING CODE AND THE 2010 FLORIDA MECHANICAL CODE, WITH LOCAL AMENDMENTS, THE APPLICABLE NFPA CODES AND THE FLORIDA ENERGY CODE. 2. ALL ELECTRICAL EQUIPMENT SHALL BE UL CLASSIFIED OR LISTED. 3. DEFINITIONS: "FURNISH" SHALL MEAN TO PURCHASE AND LOCATE AN ITEM ON THE JOBSITE. "INSTALL" SHALL MEAN TO PHYSICALLY INSTALL AN ITEM AND CONNECT IT TO ALL REQUIRED SERVICES TO MAKE THE ITEM FULLY FUNCTIONAL. "PROVIDE" SHALL MEAN TO BOTH FURNISH AND INSTALL THE ITEM. 4. TEST AND BALANCE SHALL BE PERFORMED BY THE MECHANICAL CONTRACTOR ON APPROVED FORMS USED BY AABC OR NEBB. THE MECHANICAL CONTRACTOR SHALL HAVE ALL SYSTEMS FULLY INSTALLED AND OPERATIONAL WITH CLEAN FILTERS INSTALLED PRIOR TO TEST AND BALANCE. AIR CONDITIONING EQUIPMENT 1. THE AIR CONDITIONING EQUIPMENT SHALL BE STRAIGHT COOL, WITH ELECTRIC HEAT. 2. ALL EQUIPMENT SHALL MEET THE MINIMUM EER REQUIREMENTS OF THE FLORIDA ENERGY CODE. 3. TRANE IS THE BASIS OF DESIGN WITH AMERICAN STANDARD, CARRIER AND YORK AS APPROVED ALTERNATES. IF AN ALTERNATE IS SUBMITTED, THE CONTRACTOR SHALL MAKE ALL NECESSARY CHANGES TO THE ELECTRICAL, STRUCTURAL AND DUCTWORK TO ACCOMMODATE THE SUBSTITUTION. 4. SUBMITTALS SHALL BE REVIEWED BY THE ELECTRICAL SUBCONTRACTOR FOR IMPACT TO THE ELECTRICAL SYSTEMS, PRIOR TO ORDERING THE EQUIPMENT. 5. ALL AIR CONDITIONING EQUIPMENT SHALL INCLUDE A MINIMUM 1 YEAR UNIT WARRANTY AND AN EXTENDED 4 YEAR COMPRESSOR WARRANTY. 6. PROVIDE 1" CONDENSATE PIPING AS SHOWN ON THE PLAN AND DETAIL. THE CONTRACTOR SHALL EXTEND THE CONDENSATE PIPING TO THE EXTERIOR TO SPILL TO SITE STORM RETENTION. 7. THE AIR CONDITIONING UNITS SHALL BE OPERATED DURING CONSTRUCTION WITH THROW AWAY FILTERS. FILTERS SHALL BE CHANGED DURING CONSTRUCTION IF THEY BECOME RESTRICTIVE OF AIR FLOW FOR NORMAL OPERATION. PROVIDE NEW FILTERS JUST PRIOR TO TEST AND BALANCE. 8. UNITS SHALL BE CLEANED AND ALL SCRATCHES PAINTED OVER WITH FACTORY PAINT TO MATCH UNIT. ALL CONDENSER COILS SHALL BE COMBED OUT AND ALL PANELS AND SCREWS SHALL BE INSTALLED AT THE COMPLETION OF THE PROJECT. DUCTWORK 1. SUPPLY AND RETURN DUCT SHALL BE 1-1/2" DUCT BOARD, INSTALLED IN ACCORDANCE WITH SMACNA. SEE DETAIL FOR INSTALLATION AND HANGING INSTRUCTIONS. 2. OUTSIDE AIR AND EXHAUST DUCT WORK SHALL BE GALVANIZED SHEET METAL WITH ALL JOINTS SEALED WITH MASTIC. ROUND DUCT WORK SHALL BE "THERMOFIN" OR SINGLE WALL SHEET METAL. DUCTS DO NOT NEED TO BE INSULATED UNLESS REQUIRED BY LOCAL JURISDICTION. ALL DUCT SHALL BE CONSTRUCTED AND INSTALLED PER SMACNA. 3. ALL DUCT SIZES DEPICTED ARE CLEAR INSIDE DIMENSIONS. 4. SUPPLY AIR DUCT SHALL BE SIZED AT 0.10"/100 FT. EQUAL FRICTION AND RETURN DUCT SHALL BE SIZED AT 0.06"/100 FT. EQUAL FRICTION. 5. HOLD THE BOTTOM OF THE SUPPLY AIR DUCT A MAXIMUM OF 24" ABOVE LAY -IN CEILINGS TO ALLOW FOR ACCESS TO BALANCING DEVICES. 6. PROVIDE A FLEXIBLE CONNECTION FROM EACH AIR HANDLER AND FAN TO THE DUCT SYSTEM. 7. FLEXIBLE RUNOUTS TO THE DIFFUSERS ARE LIMITED TO A MAXIMUM OF 25 FEET. 8. PROVIDE ACCESS PANELS IN DUCTS FOR ACCESS TO VOLUME DAMPERS, FIRE DAMPERS, FIRE/SMOKE DAMPERS, DUCT MOUNTED SMOKE DETECTORS AND WHERE REQUIRED TO MAINTAIN EQUIPMENT. 9. ALL FLEXIBLE BRANCH CONNECTIONS SHALL HAVE A MANUAL VOLUME DAMPER INSTALLED AT THE MAIN TRUNK FOR BALANCING PURPOSES. CONTROLS 1. ALL TEMPERATURE CONTROLS SHALL BE 24 VOLT, AS PROVIDED BY THE MECHANICAL CONTRACTOR. 2. THERMOSTATS SHALL BE PROGRAMMABLE EQUAL TO HONEYWELL T8000 SERIES, OR BY UNIT MANUFACTURER, WITH STAGES OF COOLING AND HEATING TO MATCH THE UNITS SELECTED. MOUNT THERMOSTATS AT 5'0" AFF OR AS DIRECTED BY ARCHITECT/OWNER. 3. LOW VOLTAGE CONTROL WIRING SHALL BE PROVIDED BY THE MECHANICAL CONTRACTOR.THE ELECTRICAL CONTRACTOR SHALL PROVIDE CONDUIT FOR ALL CONTROL WIRING AS COORDINATED WITH THE MECHANICAL CONTRACTOR. 4. LINE VOLTAGE (110 VOLT OR HIGHER) POWER AND CONDUIT SHALL BE PROVIDED BY THE ELECTRICAL CONTRACTOR. 5. THE ELECTRICAL CONTRACTOR SHALL PROVIDE ALL DISCONNECT SWITCHES. DO NOT MOUNT DISCONNECT SWITCHES OVER NAMEPLATES OR SERVICE PANELS. 6. TEST AND BALANCE SHALL VERIFY THE OPERATION OF ALL CONTROLS AT THE COMPLETION OF THE PROJECT. 7. WHERE SMOKE DETECTORS ARE PROVIDED AND INSTALLED BY THE MECHANICAL CONTRACTOR (NO FIRE ALARM SYSTEM), EACH SMOKE DETECTOR SHALL BE EQUIPPED WITH A REMOTE TEST STATION EQUIPPED WITH A VISUAL AND AUDIBLE ALARM TO BE LOCATED ADJACENT TO THE UNIT THERMOSTAT IN ACCORDANCE WITH NFPA 90. AIR DISTRIBUTION SCHEDULE DESIGNATION DESCRIPTION LEGEND SPECIFICATIONS EXAMPLE CD1-10-270 CEILING DIFFUSER CD1 PRICE ASCD SERIES, ALUMINUM, NECK SIZE NOTED 10" MODULAR CORE, LAY -IN MOUNTED, CFM NOTED 270 OFF-WHITE COLOR. RG1-24x24-300 RETURN GRILLE RG1 PRICE 610, ALUMINUM FACE SIZE NOTED 24x24" LOUVERED CORE, LAY -IN MOUNTED, CFM NOTED 300 OFF WHITE COLOR. RG2-16x16-200 RETURN GRILLE RG2 PRICE 610, ALUMINUM FACE SIZE NOTED 16x16" LOUVERED CORE, SURFACE MOUNTED, CFM NOTED 200 OFF WHITE COLOR. NOTES: 1. SIZES AND CFM SHOWN ON THE LEGEND ABOVE ARE FOR EXAMPLE ONLY. SEE PLAN FOR ACTUAL SIZES AND CFM VALUES USED ON THIS PROJECT. 2. LOCATE ALL AIR DISTRIBUTION PER THE ARCHITECTURAL REFLECTED CEILING PLAN 3. APPROVED MANUFACTURERS: PRICE, METALAIRE, KRUEGER, TITUS BUILDING AIR BALANCE OUTSIDE AIR INTO BUILDING EXHAUST AIR OUT OF BUILDING SOURCE CFM SOURCE CFM AHU-1 AHU-2 AHU-3 AHU-4 200 120 120 160 TEF-1 TEF-2 EXFILTRATION 50 50 400 TOTAL OUTSIDE AIR IN = 600 TOTAL EXHAUST AIR OUT = 500 BUILDING PRESSURIZATION = +100 OUTSIDE AIR CALCULATION SCHEDULE SPACE PEOPLE/SQUARE FEET REQUIRED OA PROVIDED CIA OFFICE 22 / 3018 SF 313 325 PHARMACY 2 / 399 SF 82 90 SALES 6 / 733 SF 133 140 STORAGE 0 / 613 SF 37 45 NOTE: 1. OUTSIDE AIR VOLUMES ARE BASED UPON ASHRAE STANDARD 62.1 SEEDS Engineering, Inc. 27730 Santa Anita Blvd. p: ( 813) 902-2515 Wesley Chapel, FL 33544 f: ( 813) 902-2516 jmakar@seedseng.com Wiedrick Architecture, Inc. WIEDRICK ARCHITECTURE INC. AA26001799 2020 HEIDELBERG AVE. DUNEDIN, FLORIDA, 34698 STATE OF FLORIDA REGISTERED ARCHITECT: MATTHEW WIEDRICK AR94577 �4N14 M A EN.Q SF., i No.54827 STATE OF 0 . R10 • � •NAI.EN�'� PRn.IF(-T AnnRF.q.q- Jb444 b I H AVI=. ZEPHYRHILLS, FL 33542 FLORIDA PHARMACY SOLUTIONS, INC. 13933 17TH ST. SUITE 300 DADE CITY, FL 33525 MECHANICAL FLOOR PLAN FLOOR FLAN 3/1G It =1'-011 N(2) Florida Certificate of Authorization No. 28278 NI J VV PROJECT #: 14022