Laserfiche WebLink
<br />08132 <br /> <br />Battery Charger Module <br /> <br />Specifications <br /> <br />Features <br />. Provides additional standby Amp hours for <br />control/communicators <br />. 1200mA battery recharging circuit <br />. Suitable for 12 VDC, 7 and 18 Amp-hour batteries <br />. Suitable as a stand alone 12 VDC, 1 Amp power <br />supply <br /> <br />Description <br /> <br />The D8132 Battery Charger Module is an accessory <br />device for Radionics D6112, D7112, D8112, D8124, and <br />9000 Series control/communicator panels. The D8132 <br />uses a 16.5 VAC, 40 VA plug-in transformer to supply <br />1200mA of battery charging current. An on-board, <br />green LED remains lit to indicate the presence of AC <br />voltage. <br /> <br />The D8132 can be used to increase the standby battery <br />time of a panel when instaUed with external batteries in <br />an adjacent approved enclosure. The D8132 is not to <br />be used as the sole means of standby power for a <br />panel. One or two 12 VDC, 7 Amp-hour batteries must <br />still be provided for the panel. <br /> <br />The D8132 can also be used as a stand-alone power <br />supply in non-UL applications. You can connect one or <br />two 12 VDC, 7 Amp-hour batteries or one or two 12 <br />VDC, 18 Amp-hour batteries to the D8132 in either <br />application. <br /> <br />In addition to providing increased standby time and <br />auxiliary power, batteries connected to the D8132 also <br />filter the AC power supply. The amount of ripple that <br />appears on the panel outputs is dependent on .the <br />charge state of the batteries. Radionics does not <br />recommend using the D8132 to power devices that are <br />sensitive to excessive ripple. <br /> <br />Application <br /> <br />The 08132 Battery Charger Module is suitable for <br />systems requiring extended battery standby time. The <br />D8132 is UL listed for use in Central Station. Household <br />and Local Fire and Burglary Alarm applications, Police <br />Connected, Remote Station, and Electrically Actuated <br />Transmitter applications. The D8132 is not UL listed for <br />use with the D6112. <br /> <br />Provided with the D8132 are two cables, and two sets of <br />lockwashers, nuts, screws, and terminal lugs. The <br />cables connect the D8132 to the D1640 transformer, <br />one or two batteries, and the control/communicator. <br />Additional hardware is provided for connecting the <br />battery cable to 12 VDC 18 Amp-hour batteries. This <br /> <br />$ radlonics <br /> <br /> <br />hardware is not required when connecting 12 VDC, 7 <br />Amp-hour batteries. <br /> <br />Installation <br /> <br />The D8132 Battery Charger Module and additional <br />batteries are typically mounted inside a separate <br />approved enclosure such as the Radionics D8103, <br />D8108A, or D8109. The enclosure is instaUed adjacent <br />to the control/communicator enclosure. <br /> <br />The plug-in AC transformer is installed on the same AC <br />branch circuit as the control/communicator transformer. <br />No other devices may be connected to the transformer. <br /> <br />A 4-wire harness is used to connect one or two batteries <br />to the 08132. An additional 4-wire hamess connects to <br />the AC transformer (2 wires) and the battery terminals of <br />the control/communicator. <br /> <br />The D8132 installs in the enclosure using three plated <br />screws supplied with the unit Radionics enclosures <br />provide module mounting locations with knockouts. Use <br />a Radionics D137 Mounting Bracket when installing the <br />D8132 in a non-Radionics enclosure. The D8132 <br />should be mounted towards the top of the enclosure <br />away from the batteries to avoid overheating. <br /> <br />The Radionics 08103, D8108A, and D8109 enclosures <br />provide a rectangular knockout on the door that allows <br />the green AC power LED on the D8132 to be easily <br />viewed. <br /> <br />A memller of the <br />Bosch Group <br />