Laserfiche WebLink
<br />Operational Data <br /> <br />When using the D8132 to increase your <br />controVcommunicator panel standby battery Amp hours, <br />refer to the appropriate calculation chart contained in <br />the 08132 Operation and InstaDation Manual (74- <br />04777-000). These charts detail the Amp-hour <br />requirements, controVcommunicator AuxUiary current <br />load, and the D8132 battery recharge time. <br /> <br />The D8132 can also be used as a stand-alone, 12 VDC <br />1 Amp power supply. For stand-alone applications the <br />D8132 does not provide battery supervision or load <br />shed capability and is not recommended for critical <br />loads. The D8132 is not UL listed for stand-alone <br />applications. <br /> <br />A form of battery supervision can be provided to a <br />D8132 in stand-alone configurations when connected to <br />the same AC branch circuit as the panel. AC power <br />l'ailures and restorals, which would also affect the <br />1)8132 module, can be reported by the panel to a <br />remote receiver. This supervision relies on the <br />;:issumption that AC power to both devices has been <br />affected. The Amp-hour rating of batteries on the <br />108132 should be greater than batteries connected to <br />the panel. This ensures that devices connected to the <br />108132 are powered at least as long as those on the <br />control/communicator. <br /> <br />The stand-alone D8132 and the panel must share a <br />common ground. <br /> <br />Specifications <br /> <br />Operating Voltage 16-18 VAC supplied by plug- <br /> in transformer <br />Operating Current 1200mA of rectified AC <br />Float Voltage 13.9 VDC maximum current <br />Dimensions 5 in. x 3 in. x .8 in. <br />(H x W x D) (12.7 cm. x 7.6 cm. x 2 cm.) <br /> <br />The contractor shall furnish and install Radionics model <br />D8132 Battery Charger Module where indicated on the <br />plans. The D8132 shall provide increased standby <br />Amp-hours for the specified Radionics <br />control/communicator panel. The module shall be <br />equipped with a 16.5 VAC, 40 VA plug-in transformer, <br />two sets of connecting cables and all hardware required <br />for proper installation. The D8132 shall have an on- <br />board, green LED for indicating the presence of AC <br />power. <br /> <br />@ 2001 Radionics, a division of Detection Systems, Inc. <br />PO Box 80012, Salinas, CA 93912-0012, USA <br />(800) 538-5807 <br /> <br />The D8132 shall be capable of supplying recharging <br />current for one or two 12 VDC, 7 Amp-hour or 18 Amp- <br />hour batteries. The module shall be mounted in the <br />recommended Radionics enclosure or other approved <br />enclosure. Installation shall be subject to the <br />requirements of the authority having jurisdiction. <br /> <br />Listings and Approvals <br />. Underwriters Laboratories <br />. CSFM <br />. BSA <br /> <br />Ordering Information <br /> <br /> <br />D126 <br />D137 <br />D1218 <br />D8132 <br /> <br />12 VOC 7.0 Amp-hour Battery <br />Mounting Bracket <br />12 VOC 18 Amp-hour Battery <br />Battery Charger Module <br /> <br />1S09002 0 <br /> <br />CERTIFICATE NO. A5137 <br />75-06430-000-C 8/01 <br />Specmcations D8132 <br />L515 Page 2 of2 <br />